Ford - Explorer :: 1997 - High Beams Don't Work - No Power On Wire At The Bulb Socket
I have a 1997 Explorer XLT. The high beam have not worked since I got it and now living in Virginia they are needed to pass inspection. When turned on (pushed forward) lights go out, high beam indicator comes on. When flash to pass (pulled back) lows stay on and indicator comes on. It does not have auto lamps.
What I have done:
Replaced MFS
Verified power from GRY/ORG wire on MFS when turning high beams on.
Verified power across fuse #33 when switch turned on.
Had bulbs tested, Good.
No power on high beam wire at the bulb socket.
The only thing I have not checked is what several people have referred to as a "splice" I think someone referred to it as S111? Where this is physically located or am I going to have to start the chore of tracing the wires?
Passat (B6) :: Headlight Bulb Socket Partially Melted
I was changing standard halogen headlight bulbs last night and as I was getting the drivers side bulb out the metal part came off with the bulb and I noticed the black plastic part of the socket was partially melted. Sketchy. Far as I know these bulbs have never been changed I bought the car w 3500 miles back in 06. Is there anything I should do besides replacing the melted socket? A part # would be awesome too...
View 2 RepliesPassat (B5) :: How To Remove Front Turn Signal Socket To Replace Bulb
I have a 2003 W8 wagon and my front turn signal bulb went out. I need to replace it, but am having some problems. I removed the high beam cover to get to the turn signal socket, but I am having problem removing the socket. I was able to turn the socket slightly and was hoping I could just pull it back, unfortunately it doesn't seem to want to move. Is there a trick to remove the turn signal socket so I can remove the bulb? I don't want to force anything in fear of breaking something. there has to be a way.
View 1 RepliesFord - Explorer :: 1999 - Check Engine Light Keeps Coming On / Misfire Code
I have a 99 Ford Explorer - w/217k miles. (2nd owner) .. I got an oil change 3 weeks ago, tune up 2 mos ago, and new brakes/tires within the last 6 mos, oh, and Brother-In-Law just recharged my a/c last week.
Runs well, and I hope to keep it for another few years, but having problem lately.
Check Engine light keeps coming on - I've taken it in, and they read the code, and it comes up with a misfire. Mechanic resets it, and it will stay off for a few days/weeks, and then comes back on.
Passat (B6) :: Changed HID Bulb - Warning Light Came On
I had my Passat (2006) for a couple of weeks now and this message comes up on the dash warning: "AFS inoperative". The bulb failure light was flashing as well. I have the bi-xenon lights.
The L/H bulb was changed and the warning and the bulb failure light is still there, but both headlights are working now. The major drama is that the lights are now dipped and at night we can only see about 20m in front of the car. The lights don't do the start up dance as normal.
Sonata NF (2006-10) :: Changed Battery, Now Check Engine Light On
2009 2.4 Sonata. Replaced the battery. Engine light came on after battery replacement. Engine code P0106 (MAP sensor or vacuum leak). Car drove fine before and after the battery replacement. Engine light after replacing battery?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Changed Injectors / Cannot Even Get Engine To Crank?
I changed my injectors and glow plugs on passenger side. I tried to start the engine and it wont crank (turn over). I tried to turn over by hand by turning alternator bolt counter clockwise, turns a little bit and then get very difficult. Is this hydro lock? I stuck a suction tube down injector holes and made it to the piston not much oil came out, I think the truck was a little low on oil before I started the project. The starter wont turn the engine over. I even turned the engine over by hand many times before I put glow plugs in to evacuate the cylinders. I don't know what to do?
View 14 RepliesFord - Explorer :: 2003 - Resistor Changed - Blower Still Not Working
2003 Limited explorer 237k with auto climate controls. 95 degrees out and a/c on when fan speed began going up and down a few times and then completely off. Won't work on heating as well. Rear fan works fine so I changed the resistor but still nothing. The control lights up when changed as usual but no fan. What to change next?
View 7 RepliesFord - Explorer :: 2008 - Continuous Check Engine Light
i have a continuous Check Engine light in my 2008 ford explorer. Dealer recommend replacing a sensor but I do not know which sensor to change.
View 4 RepliesExplorer :: 2003 Ford Sport Trac Dies In Reverse (ICV Changed)
We have a 03 Ford Explorer Sport Trac that we just changed the ICV on because after it would warm up it dies at intersections. Now it shutter quite a bit a dies in reverse. We took it to a transmission place and no codes come up.
View 3 RepliesFord - Explorer :: 1998 - Running Rough - Cut Out - Got PO453 Code - Changed Gas Cap But Nothing?
I have a 98 sport 4.0 i bought awhile back and its been running rough.. When driving it seems to cut out.. I had it scanned and it has code PO453 which is pressure sensor.. I was told they replaced the fuel pump when i got it.. After driving and i get out i can smell gas on the drivers side.. I replaced the gas cap but no change.. I was just wondering about this code and what i should start with first..
View 3 RepliesFord - Explorer :: Intermittent Check Engine Light - P0193 Code
My 2007 Explorer (XLT, V6 4.0L, 4WD, 175k miles) has been experiencing a check engine light, intermittently, for the past few months. I took it to AutoZone to read the code and they gave me a printout for P0193. For awhile, the light would go off after I filled the tank with gas (usually the next day) and would come again as the level in the tank decreased (typically around 1/4 of a tank). Then about two months ago, the behavior seemed erratic and I could no longer predict when it would appear. During the past couple of weeks I only recall seeing the CEL once (briefly); it's mostly been off. Saturday night I was out driving and it came on again.
About two hours later, my vehicle "conked out" on me. It started hesitating (it's been a very long time since I've run out of gas, but that's what it reminded me of). Fortunately, there was no traffic and I was able to get it off the road but didn't have enough momentum to get it into a defined parking space before it quit. I sat there for awhile pondering my options (not too many since it was the middle of the night and I don't have road service). After about 10 mins or so, I decided to see if I could get it started. It did start and I was able to drive it home (< 10 miles). It's been sitting in the driveway since because I'm afraid of getting stranded if I drive it again. BTW, I was low on gas when it died -- about 50 miles to E (was headed to the gas station when it happened, but took it home instead).
After everything I've read the past few days, I'm expecting that I need to replace at least the fuel filter, the fuel rail pressure sensor and the intake gaskets for the manifold. I am not a mechanic, don't have diagnostic tools, my funds are really limited right now and I'm pretty much on my own to figure this out.
Q1: For those who may have some knowledge about this particular issue, does the intermittent nature of the CEL give any clues to which part(s) might be malfunctioning?
Q2: I found a replacement FRPS made by Bosch on Amazon, significantly cheaper -- is this brand ok or should i stick to Motorcraft?
Q3: Any advice on the manifold gasket replacements (is one brand better than another)?
Q4: Do I really need the special tool to replace the fuel filter?
The questions above are no longer relevant. I'm in the process of "locating" the sensor. I have the air hose and throttle body off. Now I'm looking at the EGR valve. It looks like I will have to disconnect the it from the large pipe beneath it. Will I also need to remove the two smaller bolts that mount it to the manifold cover, or can I remove the cover & valve together? It looks like those little buggers are going to be challenging since they are facing the back of the engine compartment. This is rather slow-going for me, but there's no turning back now.
Ford - Explorer :: Check Engine Light Came On But No Error Codes - How To Reset
My 1998 Explorer with 120,000 mile on it. The check light just came on. I have had several auto part stores plug in the scan tool and there were no error codes. I'm looking for the reset button location. I am also wondering should there be something missed by the scan tools, will the light activate should there be a real problem.
View 9 RepliesFord - Explorer :: 2001 - Check Engine Light With EGR Low Flow Code
I have an 01 Explorer Sportrac with a 4.0, 105,000 milles. Got the check engine light with the EGR low flow code. I get this code about once a year and a new DPFE usually takes care of it. I get the sensor from Advanced Auto which explains the short life I am guessing. Last time i replaced the sensor the light came back on a couple weeks later.
After highway driving smoke starts pouring freon under the hood, passenger side, but by the time I get the hood opened its done. Cant tell where it is coming from. Could a faulty DPFE cause the smoke or do you think the EGR valve may be sticking? I was going to try a Ford DPFE this time but I hate to just throw parts at it. Where do the smoke is coming out of, air filter box????? cant see anything else over there related to the EGR system......
Ford - Explorer :: 2001 - Reset And Clear Check Engine Light
2001 explorer sport, need to reset and clear check engine light I know the problem a small pinhole in exhaust that opens up and i fill it in How do i reset check engine light...
View 1 RepliesFord - Explorer :: 2005 - Headlight Bulb Replacement?
How to change the Lightbulb in a 2005 Ford Explorer XLT? I can do most maintenance on vehicles, but this one is annoying. It is not very intuitive and I feel like there is a lot to do just to take out the lightbulb on a vehicle. I don't want to do trial and error on this and add more work for myself.
View 2 RepliesFord - Explorer :: Check Engine Light And Wrench Symbol On With Multiple Codes
I have 2007 explorer 4.0 4x4. Check engine light and wrench symbol on with codes po743 po750 po755 po po765 po966 po966 po970. Feels like it is now stuck in 3rd gear.
View 2 RepliesFord - Explorer :: 2007 V8 - Check Engine Light On - Can Only Fill The Gas Tank About 3/4 Full
I have 2007 explorer 4.6 v8. The check engine light is on, and i can only fill the gas tank about 3/4 full, after moving the gas nozzle all around and taking about 15 minutes. I read a few different things while searching. Like vapor canister need to be replaced. or the vent hose needs to be replaced.
View 1 RepliesFord - Explorer :: Check Engine Light Code P0913 - Hesitates Like Not Getting Fuel
2004 Sports Trac Got a check engine light: a code P0913. The truck , once in a while, hesitates like it not getting fuel. Is this a fuel pump problem or something else?
View 1 Replies