Ford Super Duty (1999-2016) :: 2000 F250 - Front Shock Mounts?
I need to know what the name of the part is that the front shock mounts to on my 2000 f250. Its terribly rusted on both sides and id like to learn more about replacing it. Might me called a shock mount? It saddles around the main frame on the truck.
View 3 RepliesFord F-150 - 1997-2003 :: Shock Bolt Stuck And Almost Stripped
I have a 1997 f150 4x4 and i got some new shocks for it, but I got the top nut off but the bottom bolt is almost stripped, so I am gonna buy new bolts and remove the old ones, so my question is what size bolt do I need ? I am assuming grade 8 but what length and diameter? and whats the best to remove the old bolt if it completely strips ? grinder ? drill?
View 5 RepliesFord Super Duty (1999-2016) :: Rear Shock Absorber Bolt Size?
What is the size of the bolts on the rear axle that hold the shock absorber? I believe its an M12 x70 mm long??
View 7 RepliesFord F-150 - 1997-2003 :: 1999 - Driveshaft Bolt Torque Specs
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesFord F-150 (2004-2008) :: Rear Differential Leak - Torque Rating On Bolt?
I am getting a little frustrated with a leak on my rear differential. The leak is on the front of differential rear-end just behind the four bolts you take off to remove the driveshaft. When you take the driveshaft out, there is a single bolt and the seal behind that is leaking. Here is my dilemma, I called my local ford dealership to find out what the torque rating on that bolt is so when I replace the seal I don't over-tighten. He told me there is no torque rating on it because I have to tighten, measure, tighten, measure the bolt. I was lost, I didn't have a clue what he was talking about.
View 6 RepliesFord 6.7L Power Stroke Diesel :: 2012 F350 - Transmission Pan Bolt Torque?
Searched with no results. What is the correct bolt torque for transmission pan bolts on a 2012 F350 6.7L?
View 14 RepliesSilverado :: 5.3l Oil Pan Bolt Torque Settings?
I have replaced my oil pan gasket with a felpro. I had oil leaking from the top of the oil filter. This oil pan has the filter going through it. I have replace the oil cooler cap and gasket and finally replaced the oil pan gasket. It worked. I do no have any leaks from above the filter. But I am leaking from inside the bell housing. It is still coming from the oil pan and nowhere else. (I have dye in the oils and can see it leaking)
SO I went back to the Haynes to recheck the torque settings. I originally torqued all of the bolts for 89 inch lbs Per the haynes manual)
here is what it says:
oil pan bolts:
step one (to engine and front cover)............89 in-lbs
step two (to rear cover).............................18 foot-lbs
this step two is not too clear.....
which bolts are the bolts to the rear cover??
what I think this means is the 2 long rear bolts that go to the rear cover should be 18 foot-lbs. in the haynes manual they are bolts 13 and 14.
Is this right.....I started to do this but then stopped becuase I felt I was going to strip the bolts.
This kind of makes sense due to there are no other bolts in the middle of the rear of the pan to the block.
Torque Specification For Oil Pan Drain Bolt On 3.5L?
Looking for ccess to a '13 Toyota Factory Service Manual (FSM) that states the torque specification for the oil pan drain bolt on the 3.5L?
If the '13 FSM is similar to the '05 FSM, the torque value will appear on the diagram that shows the oil pan assembly. I believe the spec is 30 ft-lbs (with a new washer), but I want to confirm.
Lexus RX 2010-15 :: Torque Specs For The Caliper Bracket Bolt?
2011 Lexus RX350 ... What are the Torque specs for the caliper bracket bolts (front and rear caliper brackets) a pdf will be great
View 1 RepliesPassat (B6) :: What Is The Part Number For Torque Insert Stretch Bolt
As the title implies I need the part # for the OEM VW Stretch bolt that holds the Torque Arm insert in place. I've had the mount on my car for a few months now and I've grown tired of it.
I re-used the OEM bolt the first time and I think I'm better off replacing it as it may not be wise to unbolt it and re-torque it for a third time. Looking for the part # for the stretch bolt? I believe it's 21mm.
Corolla / Matrix 2009-13 :: 2ZR-FE 1.8L Engine Valve Cover Bolt Torque?
I looked around and couldn't find the specs for the valve cover bolts.. I'm assuming it'll be a pretty low torque like 20 ft-lbs.
This'll be the 2ZR-FE 1.8L engine.
Passat (B6) :: Replacing Brake Lines - Banjo Bolt Torque Setting
Going to replace brake lines tomorrow and would like to confirm the torque spec on the actual banjo bolt as not to break them but also don't want to leave them too loose...
View 3 RepliesFord Excursion :: Replacement Of Body Mounts?
I need to replace the body mounts in my Ex. How do you do it?
View 14 RepliesFord Excursion :: Replaced Motor Mounts Now Vibration At Speed
I replaced the motor mounts, and now there is a vibration at speed (70 or so). I've taken it to Michigan and back, so it is probably broken in. Can these things be put in improperly?
View 13 RepliesFord Excursion :: Front Passenger Shock Top Nut Removal
Any trick that they have used before for removing the Front Passenger Shock Top Nut without removing the A/C Accumulator? The Nut I need to remove is right underneath the A/C Accumulator and I can't get a 15mm Deep Socket on the nut so that I can use an air tool to take off the nut like I did on the Driver side. Is my only option to use a 15mm ratcheting box end wrench or remove the accumulator? On AllData, they show the pics of the Driver Side which is easy to access with just a swivel and a couple of extensions.
View 1 RepliesFord Excursion :: Front Stabilizer Shock Replacement
Is there any particular front stabilizer shock I should purchase for a replacement for my 2003 X 6.0L diesel? Anything I should stay away from?
View 7 RepliesFord Excursion :: Steering Stabilizer Shock Broken
Today I noticed I broke my steering stabilizer shock. It it broke at the connection on the piston arm where it connects to the steering linkage and the piston shaft is bent. Guess it happened when I hit a rock Thursday. I am thinking of purchasing the Rancho 9000 adjustable shock as a replacement. I do not do much off road driving and what I do is very moderate. This is for a 04 Excursion, 4x4, 6.0PSD, with 285 all terrain tires, no lift.
View 7 RepliesFord Excursion :: Rear Shock Bolts And Nuts - Part Numbers?
I've noticed quite a few threads looking for the shock bolts lately. I've replaced one of mine and just had another break. Today I ordered replacements for all 4 nuts and bolts.
The Bolt part number is - N605906-S2
The Nut Part Number is - N803714-S426
Ford Excursion :: Skid Plate In Front Of Passenger Side Rear Shock
Looking to install rear sway bar on 2001 Ex. and noticed a skid plate looking thing in front of passenger side rear shock. Two questions:
1. What is that, and
2. Do I need to remove it to put on sway Bar?