Ford Excursion :: P0720 Code - Output Shaft Speed Sensor
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
Ford Transmission :: Take Off Output Flange Without Changing Tail Shaft?
Can I take off the output flange on the tranny and use a slip joint, with out changing the tail shaft?
View 1 RepliesFord Transmission :: Vibration Occurring During Deceleration - Pinion Shaft Play
I had some vibration occurring during deceleration and though it was either the slip joint or the rear u-joint because I could sense some movement back there.
After I replaced the u-joints and properly serviced the slip joint I still had the issue (although it was a little better). I now see that there is a little bit of play in the pinion shaft. I can't really shake it back and forth, but if I hit it hard upward it clearly has play.
What should I do next? I have read a bunch, but would like to get an expert to chime in.
Ford Excursion :: Stall Out At Almost Every Stop Light / Code P0720 - Output Shaft Speed Sensor?
I just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?
Ford 7.3L Power Stroke (1999-2003) :: Transmission Output Shaft Seal Removal
I'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesTorque Specification For Oil Pan Drain Bolt On 3.5L?
Looking for ccess to a '13 Toyota Factory Service Manual (FSM) that states the torque specification for the oil pan drain bolt on the 3.5L?
If the '13 FSM is similar to the '05 FSM, the torque value will appear on the diagram that shows the oil pan assembly. I believe the spec is 30 ft-lbs (with a new washer), but I want to confirm.
Accent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesFord Excursion :: Transmission Died - Torque Converter?
So here I am driving away for the fuel station and then the tranny tries to shift and I hear and feel a loud clunk followed by no power. I have had no previous issues with the tranny but I believe it has not had any previous work done. The truck is an 02 7.3L with 200500 miles. I am guessing the torque converter is the culprit it still had very little forward motion when I tried to move the truck didn't matter what gear I was in. I intend to have the tranny beefed up but don't intend to go crazy. I do tow an 11,000 lbs TT on a fairly regular basis and have a PHP 6 position switch which can be set for as much as 120 hp from stock but don't do any hot rodding. I am mostly just looking to beef it up and provide as much strength towing.
View 2 RepliesFord Ranger / B-Series :: 1999 - Output Shaft Seal Won't Stay?
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
Ford Excursion :: Transmission Making A Whining Noise - Torque Converter Or Pump
I recently bought a 2001 x w 145,000 miles. The transmission was making a whining noise when i bought it but it still shifted smooth and ran great. The truck has been serviced by the local Ford dealer its entire life with dozens of routine maintenance performed. With 145,000 miles should I wait for the converter to go out and just install a new transmission. It only gets drove on the weekends to go to the lake.
View 7 RepliesFord Ranger / B-Series :: 2004 4x4 - Mild Clunk / Drive Shaft Play
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 RepliesCelica :: 2000 GT - New Output Shaft Seal Leaks
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
Lexus GX 2010+ :: Front Differential Leaking From Drive Shaft Output
My front diff appears to be leaking from the drive shaft output. it's not enough to leave drips but the skid plates are oily. Having the dealer look next week. 60k on a 2011 460.
View 3 RepliesCorolla / Matrix 2009-13 :: Tranny Output Shaft Bearing Gone At 67000 Miles
So my girlfriend got this car (2013 corolla s) a few months ago and we started hearing a funny noise, I thought it was a wheel bearing going but nope its the ouput bearing on the tranny, passenger side. is this common on corrollas? how hard is it to change? I have a tranny from an 06 corolla, are they the same? and could i just swap trannies if changing the bearing is too difficult?
View 2 RepliesYaris/Scion & Vitz :: 2001 Toyota Echo - Output Shaft Bearing Making Noise
I have a 2001 Toyota echo 2001 210.200 km and my output shaft bearing makes noise and I cant know the level of my transmission fluid bcoz I don't have dipstick and i bought trans 75w90 oil os that ok and how can I add this?
View 1 RepliesFord Excursion :: Change Out Alternator To High Output?
I decided to change out my alternator to a high output. After researching I've decided to go with a DC Power...I'm planning more lights and a power inverter. Any recommendation on which one? I don't care what it cost just don't want to over do it, can too many amps hurt anything? Also, on my previous EX I did the big 3 upgrade. Is it the same on a 2 battery setup?
View 14 RepliesFord Excursion :: V10 High Output Alternator Wiring
Bought a Powermaster 250amp alternator for my '05 V10. Says I need to upgrade my power and ground wires to 4 gauge with fuse on power cable. I don't really run too many accessories other than HID heads and fogs and 2 DVD screens for the boys.
Do do I really need to upgrade my wiring? Can't imagine I'm pulling much more amperage than stock (130amp on my truck).
Silverado :: 2005 - Loud Squeak Coming From General Area Of Torque Converter Or Drive Shaft
I've got a 2005 Avalanche (basically, a Silverado) which has suddenly developed a possible illness. Whenever I start the truck and begin moving (forward or reverse), I hear one (and only one) loud squeak that seems to be coming from the general area of the torque converter or drive shaft (but who knows exactly). The squeak doesn't happen immediately upon moving but always happens within the first 20-30 feet of movement and then no more. If I put the truck in park, re-engage the automatic transmission and start moving, I cannot recreate the sound.
However, if I turn off the engine altogether, restart the truck and begin moving, it happens again exactly as before. It happens every time the vehicle has been restarted, regardless of whether the engine is hot or cold. Once it's happened, I can drive hundreds of miles and it won't happen again until I turn off the engine and restart it. Further, I've determined recently that if I start the truck on a hill and let it roll while in neutral and without a foot on the brake, the squeak still happens. Therefore, it's not dependent upon the transmission being in gear or the brakes being applied!
Ford Transmission :: 1986 - Replaced Torque Converter Now AOD Transmission Won't Shift Out Of 1st Gear?
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 Replies