Ford Excursion :: Blend Door On AC System - Windshield And Front Dash
Having issues with the blend door on the AC system. I will have it on AC or MAX AC. I will have it on the setting to be point out of the dash at me. It occasionally will switch to the defrost windshield setting. I can hear the blend door moving and changing from chest level to the windshield.
View 12 RepliesFord Excursion :: Passenger Side Rear Door Will Not Open?
The passenger side rear door will not open. I've tried from the outside handle, inside handle, jerking, pushing, etc. Nothing.
How in the world can I find out and fix the problem if I can't get the door open to get the door panel off??? And yes, I've tried unlocking it...
Ford Excursion :: Passenger Side Door Locks Are Slow
I did look but couldn't find. So the locks work like a bullet when using the remote. However, they...especially the passenger side door locks are slow. Passenger side struggles to move at all on some occasions.
View 13 RepliesFord F-150 (2009-2014) :: Cold Air Blowing At Driver Side - No Fuse Malfunction - Blend Door?
got in the truck tonight and she is blowing nothing but cold out the drivers side but the passenger side works as advertised for temp settings. I have been trying to see if there is a self test mode like the earlier year trucks have to see if there is a code. She is dual zone climate/digital so its an EATC if I am not mistaken. I have tried power cycle, pulled and re-installed climate fuse after inspecting. Tried some of the earlier year self test button combinations to no avail. I did notice if I hit defrost a few times after hitting the power and defrost that the temps would go all 00 but I don't know if that is what I am looking for. I probably know my answer which includes tearing out the dash but how to proceed. Bought her with an aftermarket power train warranty so electronics are off the table for warranty. I know the stealership will charge out the rear to fix it too. All signs so far point to a blend door which is not good at all.
View 14 RepliesFord Super Duty (1999-2016) :: Dual Climate Control - Passenger Side Blow Hot Air - Blend Mode Actuator
2008 F-350 Lariat, 6.4L, dual climate control. The passenger side blows ONLY hot air whereas driver side seems to blow whatever is called for. Is it right to assume this is the passenger side actuator, and this actuator is the "easy" one to replace (i.e. not pulling dash)? I read in another thread that there might be a question on determining the correct one to replace, so therefore I ask for clarification. How to verify if my assumption wrong?
View 4 RepliesFord A/C :: Blend Door Actuator - Clicking
What is the difference between :
Part # XF2H-19E616-FA and
Part # YL5Z-19E616-AA?
The middle numbers are the same. And they look the same? the first one is mine. Blend door actuator out of a 2000 ford windstar. Will another part # work? If the connection is the same?
Ford A/C :: 1999 - New Blend Door Actuator Won't Working?
I have a 99 EB Expedition 5.4 with EATC climate control. I replaced the heater core that had been leaking severely. When I got the dash back on I adjusted the controls with the engine running while watching the blend door actuator under the dash. it moved but not as much as I thought it should. So I drilled an "inspection" hole behind the glove box and into the plenum cover. I watched the blend door open and close when the hot/cold buttons were adjusted, but the movement was intermittent.
I'd checked the blend door for cracks prior to installing the heater core and found none. I left things alone for a day while I drove as normal. When I had time to work on it again, the actuator quit working. I figured it was damaged from the coolant leaking into the cab so I decided to replace it. It was indeed full of coolant. I bought a Dorman actuator (part #604-216) and plugged it into the wiring harness to test it before installing it. I adjusted the controls with the ignition in the "run" position and nothing happened. I'm at a loss as to what could be the problem. I've searched for this problem, but the only threads I find are incomplete or deal with the "manual" controls. I checked all my fuses and they are all good.
My questions are:
Could I have bought the wrong actuator? Would the harness fit the "manual" actuator? The part number was identified as being for the main blend door for "automatic" controls. Is there a possibility the EATC head unit is bad? It still sends air to the panel, floor and defrost when adjusted.
How do I test the voltage at the connector? I just bought a multimeter but I'm not sure which wires in the harness deliver power to the actuator. I know there are a lot of people on this site who've gone through the heater core/blend door ordeal and have lived to tell about it. What I should do next.
Ford Aerostar :: Blend Door Actuator Location
Where is the Blend Door Actuator on the ford Aerostar?
View 14 RepliesFord F-150 (2009-2014) :: Blend Door Actuator Re-Calibration Before Using?
Time for me to replace the actuator. I just have one. I've watched many videos on it but none say anything about re-calibration before using. A few posts say this is needed. Is it? if so how is it done?
View 6 RepliesFord A/C :: Blend Door Actuator Broke (Gear Inside)
I have an Explorer with automatic A/C. The blend door actuator broke (a gear inside) so I replace it with a Dorman part (could not find the Ford ones anywhere). Part #604-202, looks identical and fits. But... doesn't work.
If I do the EATC test (OFF+FLOOR, then AUTOMATIC), the display shows error coded 024, 025, 052. What is the meaning of those?
Ford - Mountaineer :: 2003 - Very Little Heat In Cabin But Not Blend Door?
My 2003 mountaineer 4.6L has front and rear heat. The issue is the heat in the front is barely warm and the heat in the back is poor. I have replaced the blend doors front and back and I'm sure they work as I can go from cold to barely warm and back again when I change the temperature setting.
I can feel hot fluid going from the engine to the front heater core and also down under the vehicle to the rear when the vehicle is warm. The return on the front is almost cold - so heat is being given up by the heater core in front, but it seems to me that if the return is almost cold, there's not enough hot coolant delivery. The overall heat is very poor in the cabin.
The coolant temperature gauge is steady and just below 1/2 with no erratic movements. I flushed the front heater core a couple years ago. Coolant has also been flushed last year. I know that the heat is underpowered in this vehicle, but it's a far cry from when it was new.
Ford A/C :: 1997 F150 - Blend Door Stuck In Hot Position
Dad has a 97 F150 with some heater issues. He put a new potentiometer in and it didn't work. We he turns the dial to cold, it still blows hot air. Defrost =hot, vent=hot, a/c=warm etc.....
The dealership told him that the blend door might be stuck. My question is, how hard is this to fix? Is it something that I can just stop by after work and quickly fix. What is involved in fixing this and where it is?
Ford F-150 - 1997-2003 :: Replace Blend Door Actuator?
Whenever my A/C is turned on, it blows nice cold air. As long as the blower is on "1", "2", and sometimes ", it blows cold air. If I turn it to "4" I can hear a small "thud" behind the dash. It sounds like the blend door is shutting. All my functions work like they should. I think the actuator is goin out and isn't pushing the door all the way closed, and when I turn it to "4" it pushes it te other way.
View 5 RepliesFord Ranger / B-Series :: A/C Works Occasionally - Blend Door?
Compressor clutch engages, lines are cold, when it works air is cold. A/C guy thinks the blend door isn't working right, is it vacuum operated or electric?
View 3 RepliesFord Ranger / B-Series :: 1998 - Replace Blend Door Actuator?
I purchased a 6.7 Diesel 2014 F250 Super Duty Crew Cab about 3 months ago. Yesterday I started my truck using the remote starter from inside my house. Seconds after I heard a loud noise. Looked outside, saw nothing and thought nothing of it till I went to open my door and realized that the driver door window shattered! I live in a quiet area, it wasn't a rock thrown at my truck or anything like that, it just Blew!!!!
I'm wondering if the truck might have some sort of pressure or torque if you wish on that window to make it just pop! My mirrors were folded in however I can't see that playing a role......
Ford Ranger / B-Series :: 1997 - Blend Door Motor Removal?
My actuator/motor doesn't have the screws that hold it on. It's just clipped down. Can I just pry it up & off with out it breaking the clips that hold it down? It's a 97 Ranger.
View 2 RepliesFord F-150 (2009-2014) :: Blend Door Clicks When Truck Turned Off?
Question: blend doors clicking even when the key is removed from the ignition? Mine clicks for quite awhile after I turn off the truck (probably 10 mins or so, I haven't stuck around to see when it finally stops) Asking out of curiosity....and this thread may put some people at rest down the line.
I do love this truck and I don't mind working on it at all. The Blend doors allow me to paint the dash trim with Bright Aluminum Plastidip.
Leaky T coolant connector which I don't mind.....wanted to switch out to a 170 degree thermostat (SSI Tuned and South Texas Heat) and do a coolant flush anyways. Might as well hammer it all out. No biggs.
Ford Excursion :: 2002 - Passenger Door Lock Would Not Unlock
This afternoon the Passenger door lock would not unlock, with switch, key fob or door pad,you can hear it and the lock rod moves a little but will not unlock. Now it won't lock or unlock, you can hear the actuator and see the lock rod move a little but it just won't get there. Should I get a part in hand before I tear into it or could it be a easy fix with no parts. 2002 Ex XLT 4X4
View 3 RepliesFord F-150 - 1997-2003 :: 2002 - Heater Won't Working - Replace Blend Door?
Over the last few days I have read several threads about heaters not working and blend door replacement. My '02 4.6 F-150 has 250k+ miles and I've always done regular maintenance on it. With the cold front moving in I've noticed that the heater is not blowing hot air. I flushed the radiator and flushed the heater core several times to make sure the core was not clogged. I also replaced the upper radiator hose because of the "crunchy" sound when squeezed. I also replaced the thermostat. Still, the heater is not blowing hot. I assume like many others that the blend door needs to be replaced. My question is do I need to replace the door only or the door and the motor (actuator)? I guess I need to test the motor before buying a new one. I saw a video where you remove all the components on the transmission hump and can actually stick you finger in the motor opening to see if the shaft has come apart.
View 8 Replies