Ford Excursion :: 1989 - Changing Brake Lines - Need Scan Tool?
Next on my list of needed repairs is new brake lines. The ones running along the frame are rusted pretty bad. I had a 89 F-150 bust a line once and it got real interesting so I would like to change these before that happens.
I have searched and still not gotten a clear answer as to whether I need to get a scan tool and do something with the ABS pump. I would like to know if the scan tool is necessary.
Honda - Accord :: 1995 - Changing All Brake Lines?
Have 1995 Honda Accord with apx. 231,000 miles and needs all new break lines under the car. Honda Dealer states 12 hours of labor at $100 per hour. Should I go elsewhere or sell the car for $600 to the parts guy at the dealership offering to buy it since I wont pay the cost at this point to fix the car? Gas lines are all fine underneath by the way - I asked them to look since they could go next I would assume.
View 6 RepliesFord Excursion :: Rotted Brake Lines / Replacement?
Is it a do it yourself job to replace brake lines. Never done it before or even seen it done. Special tools required? Will the auto parts store know exactly what I need? Are these questions answering my question?(don't do it) ...
View 14 RepliesFord Excursion :: How To Remove The AC Lines
I've got the front of the excursion done with my spring swap finally and now it's onto the rear. How do I move these ac lines along the passenger side to get them out of the way from that shackle bolt? I see the brackets holding them but since they are all hard lines how many do I have to remove?
View 3 RepliesFord Excursion :: 2003 V10 - AC Lines Leaking
I believe my rear AC lines in my 2003 EB V10 X pooped the bed on me today and Ford wants 3K to fix. I'm wondering if I could fix it my self. The leak was a bright green color so I'm assuming it was 134 or what ever in in the AC. The leak is right behind the passenger side of the motor just a little lower than the head. The dealer wants to replace almost everything for 3k but they don't want to budge on just repairing the broken line.
View 9 RepliesFord Excursion :: A/C Is Leaking Where 2 Lines Go Into Condenser
Ac is leaking where the 2 lines go into the condenser. I went to Ford and bought OEM o-rings thinking it would be an easy fix. HA! New o-rings were put in by a mom and pop garage. Still leaking. Guy said it wasn't, but with my uv light I could clearly see the dye. Went to a recommended guy. He took it apart, cleaned the hoses where the o-rings sit. They were kinda dirty from leakage and stuff so he cleaned them up with a wire brush and 2000 grit.
Recharged, and we both looked with his huge uv light. Bad condenser, drivers side lit up like a night light. Replaced the condenser with an aftermarket condenser. Recharged, STILL LEAKING from where the hoses go into the condenser. Vacuumed down the system... Removed hoses, checked o-ring fit. They are snug on the hoses and have some resistance when plunging the hoses back in. What gives? I'm 360.00 into this this week...
Ford Excursion :: How To Blow Out Rear Heater Lines
I'm 1/2 way through a flush and water pump replacement. Its going to get cold and I don't want to blow any heater lines. I have the pump off and the block drained (I also managed to get some coolant into the block - but not the rear heat).
I don't see an easy place at the front to disconnect the lines. I'd like to blow them out just to be safe. What is the best place to disco in the front or if I even need to - can I just disco 1 in the rear and then blow in both direction?
I fear that there may be some vent door closed that will prevent flow. I can't start the truck - I can turn the key on.
Ford Excursion :: 2002 - HPOP Is Leaking A Bit From One Of The Lines
I bought a 2002 Limited EX, 164K on a 7.3 diesel, its been a California truck its whole life, but still has some "rust" on it... I'm sure it can mostly be wiped away with a rag and some solvent . I mostly bought this vehicle to tow my track car around (1993 Mazda RX7) and so my friends can be comfortable while I drag them all over to be my pit crew - the rear captains chairs are a sweet feature.
Unfortunately this is the only picture I have right now... At the pump...
First things to address were the EBPS and EBPS tube, replaced those today... And the HPOP is leaking a bit from one of the lines I think, I ordered some gaskets and whatnot from Riffraff and will address that next weekend.
Ford Excursion :: Tranny Lines Rusted And Leaking?
Noticed Tranny Fluid under the Ex last week and after further inspection, it is definitely the lines rusted, by the end of the week it was leaking pretty good with the motor running. Picked up the lines from Ford and bought a 5 gal pail of MerconV from NAPA. Going to replace the tranny fluid after I replace the lines. 109k on the truck and never serviced the trans. Never had an issue with this truck, shifts nice and tight. Found Mark W's Fluid Changing procedure which looks pretty simple.
View 4 RepliesPrius (2001-03) :: Brake Fluid Dripping Down On The Brake Lines
seem to be losing brake fluid from the area of the ABS system and it dripping down on the brake lines underneath. Noticed this when draining excess oil from the engine (dealers!!!!). I'm thinking this has been leaking a long time. I have the worst luck finding a reputable mechanic anymore and if I can't trust a dealer...
View 9 RepliesFord Excursion :: Vacuum Leak In The Lines Coming From Electric Pump
So, my original pump finally died and I replaced it....however upon doing so I realize there is a leak/crack in the lines as it never shuts off (explains why the factory one died).
After a bit of troubleshooting, I've discovered the leak HAS to be down in the passenger fender where the black and grey lines travel over the blower housing and go straight down up against the inner fender wall.
Where doe these come out or connect? I clearly cant get a hand down in there...does the inner fender well have to come out to access this? or is there a junction box/splitter somewhere accessible?
Ford - Explorer :: 1996 - Brake Lines Routing
On my 1996 explorer it has 2 brake lines that come out of the master cyl, then they go into the anti lock, then 3 lines come out of the anti lock. We replaced some bad brake and now have those 3 that come out of the anti lock mixed up. Which one of those 3 goes to the back?
View 6 RepliesFord F-150 - 1997-2003 :: Brake Lines Leaking?
Blew a hole in the 3/16 inch line to the rear on the left frame rail, behind the gas tank. Lost all brake function.
Got the truck home and inspected. The line was rusted bad about 6 ft long from the connection at the rear hose to the axle, up to the rear seat area ( crew cab). From the drivers seat forward, the line looks very good. The line across the rear axle from left to right looks very good. I bought two 50 inch standard lines 3/16 inch. Started at the rear hose connection 6 inches behind the gas tank and ran forward to the rear seat area.
Cut about 32 inches of the other 51 inch line and connected and ran forward to below the front seat area. There is a metric connector at this point. I cut an inch in front of it to eliminate it. NAPA sells a high psi compression fitting ( steel , 10,000#) that you can connect two 3/16 inch lines together. I did that under the drivers foot area. I have done two different 2002 F150s in the last year due to this failure. Something to look into. Not nice to loose brakes in traffic.
If your worried about the steel compression fitting, don't. I have used these on several cars and trucks over the last 15 years. Make sure you get the STEEL high pressure compression fitting. Total line replaced on CREW cab, 51 + 32 inches. Pops right back into the original plastic clamps.... I might mention, that is where the failure was, under the plastic clamp at the rear end of the gas tank area.......... crud must collect on the clamp.
Ford F-150 - 1997-2003 :: 1999 - Brake Lines Diagram?
I have a 1999 Ford F-150 4X4 w/4.6L V8 W code, I recently lost all brakes. The primary line from Master Cylinder to ABS Pump rusted out completely. Replaced them but the other lines from ABS Pump to wheels are looking real bad. So I need to replace them, however I have no idea what the routing system looks like. Looking for a 97-03 F-150 Brake Line Diagram? I live at the jersey shore... so yeah rust is extremely common.... unfortunately.Also, where to get line assemblies?
View 7 RepliesFord Brakes/Suspension :: Way To Bend Brake Lines Without A Bender?
Is there a good way to bend brake lines without a bender? I have two brake lines to bend that are probably no longer then 3 feet and don't want to buy a bender.
View 6 RepliesFord Brakes/Suspension :: 1999 F150 - Getting Air Out Of Brake Lines?
I am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Air In Brake Lines / ABS Pump?
What happens if or when you get air in your brake lines and the air gets into your ABS pump/module? What are the symptoms? Anything other than a soft pedal? My ABS module keeps thinking one of my tires is sliding when i am driving and pulses my pedal and i am at a loss.
View 14 RepliesFord Brakes/Suspension :: Why Are The Brake Lines Coiled Near Master Cylinder
Why the brake lines have 2 or 3 coils in them near the master cylinder? Makes it a real pain to work on anything down in that area. Always snags ratchets and stuff...
My brother and I were discussing it the other nite, and the conclusion we came up with was, the first guy ever who was installing a brake system had tubing that was a couple feet too long, and couldn't find a tubing cutter, so he coiled them up.
Then the next guy saw that and figured "hmm, so THAT'S how it's done", and so on... Kinda like the story about the lady who always cut off both ends of her ham before she put it in the broiler..
Ford Ranger / B-Series :: 1988 - Rusted Rear Brake Lines
I am going to fail State safety inspection due to a problem with my brakes. Months ago when I was trying to get it through emissions testing the mechanics looked under the truck to see where the brakes were leaking. All they told me was the rear lines are rusted through and need replacing.
From my reading I believe the lines are 3/16" line and I think they go around the back of the fuel tank and up the frame rail. Correct?
My questions are, what length line do I need (I am not a hard-line expert, but I will try). I want to order some ss line so it won't rust through again. Is the system made of small sections threaded together? Or is it one long section? And what else would I need/want to replace along the way?