Ford Brakes/Suspension :: 1979 - Changed Brake Lines And Master Cylinder But Still Soft?
I have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 RepliesFord Brakes/Suspension :: 1987 - Brake Pedal Slowly Going To The Floor - Master Cylinder?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 RepliesFord Brakes/Suspension :: 1993 F150 - Rear Brake Locking After Master Cylinder Replacement
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 RepliesFord Brakes/Suspension :: 2001 F350 - Brake Pedal Go To Floor As Pressure Is Applied - Bad Master Cylinder?
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 RepliesCelica :: 1991 - Master Cylinder Brake Lines?
Which line goes to front brakes and which to rear from the master cylinder?
View 1 RepliesFord F-150 - 1997-2003 :: Winded Brake Lines From Master Cylinder To Front Splitter Block?
What kind of brake line is it and if is replicable with regular brake line? I'm just replacing long line between front and back splitter block and just would like to know what is it. What is purpose of that braiding (?) at front brake lines and why they wind down instead of going straight. Part of that long line is braided too, part that go across frame.
View 3 RepliesFord Brakes/Suspension :: 1953 F100 - New Master Cylinder - No Pedal At All?
I have a '53 Ford F100. I have a PB conversion kit on it. The master cylinder & Booster are under the floor. I have used this setup for many years. Recently my master cylinder went bad. I replaced it with the same model. I bench bled it, and installed it. I also added a remote fill kit, since it's difficult to check & fill. Because of the booster, the master cylinder no longer sits under the hatch in the floor.
I got everything installed & connected, then bled all 4 wheels using a bleeder kit with an electric vacuum pump. The fluid runs clear & no bubbles, but I can't get a pedal by pumping. I have no leaks. I tried with the engine off, and running. I have felt soft pedals before, but I have no pedal at all, it just goes to the floor.
Ford Brakes/Suspension :: 1979 F350 - Master Cylinder Replacement?
I was wondering if there was how to on doing the MC replacement? The brake pedal goes to the floor almost every time you press on the brake?
View 1 RepliesFord Brakes/Suspension :: Way To Bend Brake Lines Without A Bender?
Is there a good way to bend brake lines without a bender? I have two brake lines to bend that are probably no longer then 3 feet and don't want to buy a bender.
View 6 RepliesFord Brakes/Suspension :: 1999 F150 - Getting Air Out Of Brake Lines?
I am having trouble big time getting air out of my brake lines. I put new front pads and rotors on and also had to replace the brake line coming from the caliper as it kind of crumbled and needed to replace the next line up that goes to the ABS block on the left front. After doing this, I bled that wheel only and at first it was ok until the brake line on the right front at the caliper also broke when I was pushing on the brake pedal with the truck running, spewing fluid all over. I have tried to bleed using a decent vacuum bleed setup from Advanced Auto but keep getting massive amounts of air coming out and when I start the truck and hit the brake pedal, it goes to the floor. Could the master cylinder be bad? I have checked every connection that I made and all other connections and there are no leaks at all. I am stuck in the garage! The truck is a 1999 F150 4x4 with 4 wheel ABS.
View 1 RepliesFord Super Duty (1999-2016) :: 2001 - No Brakes After Replacement Of Brake Booster And Master Cylinder?
A few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
Ford Aerostar :: Brake Master Cylinder Cap Leaking
I replaced my MC cap and gasket less than a year ago with a Dorman replacement and I'm leaking again, already. I don't want this to be an annual thing! Any good quality replacement? Is there any tip or trick to get the gasket to seal better?
View 9 RepliesFord :: Brake Fluid Leaks From Top Of Master Cylinder Reservoir
Early 70's Ford truck. The brake MC fluid is filled but not overfilled, and doesn't leak at all when the truck is parked. It can sit there for a month and never leak a drop, parked. But when I drive the truck, even just around the block, then park, and look inside the engine compartment immediately the brake MC is dripping brake fluid. It appears the leaking mode is by the fluid somehow jumping up and coming over the top edge of the MC when the truck is in motion or when the brakes are applied. All my diy'er years of replacing brake master cylinders on Ford Galaxies, VW Rabbits, Corollas, and this truck, I've never seen this kind of weird brake problem before. On this MC design it seems there's sort of a rubber baffle inside the lid of the MC, and that's present and accounted for.
View 17 RepliesFord F-150 - 1997-2003 :: Brake Bleeding After Putting In A New Master Cylinder?
...Is there anything special that needs to be done for brake bleeding after putting in a new master cylinder? I decided today to flush my system with my vacuum bleeder and now my pedal slowly falls to the floor at a light...No problems in a panic stop or otherwise, just falls to the floor slowly when braking...no leaks, so I'm assuming a master cylinder is an order....
View 14 RepliesExplorer :: Fluid Squishing Around Master Cylinder After Brakes Bleed
I have a 1999 Ford Explorer Sport 4.0 SOHC.
I change the rotor, calipers, and pads on the front end.
When I went to bleed the brakes I got some fluid, then I got none.
I can hear fluid squishing around up near the master cylinder, but none coming to the caliper.
I see a bleeder screw on the master cylinder.
Before the car came to me the person had, had low fluid, but had brakes. Now the pedal just goes all the way to the floor with no effort.
There are no leaks or broken lines anywhere.
Dodge - Caravan :: Soft Brakes In Spite Of New Master Cylinder
Lost braking power. Replaced master cylinder. Brakes went soft again. Shop says it is something to do with the ABS Control Unit (?). Took it to dealer who said it is a leaking master cylinder. Back to shop which claims nothing wrong with new master cylinder and it i the ABS blah blah. Dealer says it can't be ABS. Went to another shop. Replaced master cylinder again. Brakes still soft. No one can figure this out and I am stuck with very soft brakes.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Removing Brake Master Cylinder?
I tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
Ford F-150 - 1997-2003 :: 2002 - Brake Light On After Changing Master Cylinder?
ll, I changed out the master cylinder on my 2002 F-150, disk brakes front and back w/ ABS. Bleed all the air out and bench bleed the master cylinder. I have good pedal but the brake light will not go out.
View 6 RepliesFord F-150 (2004-2008) :: 2006 - Brake Light On Intermittently - Master Cylinder?
My son's 2006 F-150 4x4, with 107,000 miles, has in intermittent brake light on. I replaced the rear pads, as they were nearly into the rotors. The brake pedal feels fine in all braking conditions. Could the master cylinder still be going bad? Anything else to check?
View 4 Replies