Ford - Escape :: 2003 - Brakes Unexpectedly Failed / Pedal Went Straight To The Floor
I have a 2003 Ford Escape 3.0l V-6. In June while driving to a job interview, my brakes unexpectedly failed. With absolutely no warning, the pedal went straight to the floor. I replaced the master cylinder...problem solved. 5 months later, driving to the gym, after stopping successfully several times with no mushiness in the pedal, at an intersection, the pedal goes straight to the floor...no stopping power.
I can't remember if the brake light came on last time. This time it did. Both times the fluid in the reservoir was full and looked to be relatively clean. Both times there were no apparent leaks in any of the fuel lines, abs module, at the cylinder, etc. I'm no slouch when it comes to car repair. The master cylinder replacement was done correctly, the lines were bled properly.
I have my own theories but I don't like any of them as my car rolls properly at idle, my brakes have not, nor do they currently make any noise or grinding sounds, and the pedal goes all the way to the floor.
Ford Excursion :: Lost Brakes - If Press The Pedal To Floor At Low Speed Vehicle Eventually Stop
So tonight, I lost most of my brakes. If I kept at low speeds and pressed the pedal to the floor I could eventually stop, but not well. I imagine this might be more of a general question not specific to Ex's, but I thought I would start here.
View 4 RepliesSanta FE SM (2001-06) :: Brakes Pedal So Soft That It Goes To The Floor
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
Ford Brakes/Suspension :: 2001 F350 - Brake Pedal Go To Floor As Pressure Is Applied - Bad Master Cylinder?
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 RepliesFord Super Duty (1999-2016) :: F250 - Clutch Pedal Went Straight To The Floor Boards
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesGolf IV / Jetta IV :: 2003 - Clutch Pedal Went Straight To The Floor With No Resistance?
So last evening, I went to start my car and the clutch pedal went straight to the floor with no resistance. Car started and was extremely hard to get into every gear. Felt like the only thing pushing the clutch pedal back up was the spring underneath the pedal itself. Clutch pedal was 100% just the day before. Got the clutch line bled (vacuum bleeder) and it worked fine again.
Any clue as to what could caused this overnight?
Its a AWP 1.8t jetta with ASR.. I believe I came across something about a revision in the hydraulic line but I'm not sure.
Tiguan :: Grinding When Downshift / Clutch Pedal Stuck Straight To The Floor
I've been driving manual 12 years, all my driving life, and been in 10+ manual vehicles during that time, including a 10+ year stint in a 1.8T Passat with a 5-speed.
In all that time, and all those experiences, I've never replaced a clutch, damaged a clutch, or had one problem. In fact, I consider myself a very good operator of the manual transmission.
This is preface to my current situation. 2009 Tiguan (early build) 2.0T 6M, driving at 57mph in 6th gear - downshift to 4th to pass a truck and WHAM. Grinding, confusion, and then the clutch pedal stuck straight to the floor. Glide to a stop on the side of the bayou road.
Totally immobile vehicle. Impossible to shift into gear, or get the pedal off the floor except by pulling. Smell of acrid smoke.
VW dealership says "we're doing a courtesy warranty repair" on the clutch, flywheel and bearings, as if it's my fault. Impossible. This is a mechanical defect if I ever saw one.
Santa FE SM (2001-06) :: 2005 - Brakes Locked Up And Began To Smoke - Pedal Went To Floor - ABS Light On
My 18 year old daughter has a 2005 Hyundai Santa Fe that I owned for 8 years before passing down to her. Just recently she was driving when all 4 brakes locked up and the brakes began to smoke when she attempted to drive it to a location where she could pull over. The pedal went all the way to the floor. ABS light is on. Had a tow truck bring it to my brother's house. The tow truck guy was able to back it off his truck and it stopped fine. Later when my brother test drove it, the same problem occurred. My brother replaced the Master Cylinder but it didn't work.
View 1 RepliesMalibu - Chevrolet :: 2001 - The Brake Pedal Would Drop To The Floor While Driving
I bought a 2001 chevy malibu about a month and a half ago.when I test drove it,didnt notice any problems or leaks...after driving it for a 2 weeks...the brake pedal would drop to the floor while driving and then if I hit it again real quick it would be ok...this problem would happen now and then....we replaced the right front caliper thinking that it was sticking and bled all the brakes..There was air in the system..everything was fine for about two more weeks then while driving the pedal would get hard when applied and then drop again..not all the way to the floor,and it alternates that way..what are your thoughts? I don't have much money to fix this problem.
View 14 RepliesFord Brakes/Suspension :: Brake Pedal Goes All The Way To The Floor
My dad is having problems with his truck, brake pedal goes all the way to the floor even after bleeding all the brakes and the master cylinder. The wheel cylinder didn't have clips in it and he fixed it and it hasnt changed. What do we do? Its a 1993 f150 4.9l.....
View 4 RepliesFord F-150 - 1997-2003 :: Brakes Pedal Goes To The Floor?
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 RepliesFord Brakes/Suspension :: Brake Pedal Goes To The Floor
I did a complete rebuild of my brake system in April. Drums, shoes, wheel cylinders, springs, hoses, pads, rotors, calipers, master cylinder, proportioner valve and flushed all the lines and refilled with synthetic fluid. I have made five trips from Southern California to Idaho hauling home furnishings, one trip to Oregon and one trip to Northern California since overhauling the brakes with everything working great. Now something strange is happening. The brake pedal goes to the floor with very little resistance. It isn't spongy like there is air in the lines. It just goes to the floor if you push it all the way down.
The truck stops ok but it is really scary with the pedal going down like that. You can feel when the rear brakes come on because there is a little resistance in the pedal when they come on. You can actually lock the rear brakes up and skid the rear tires. If you push the pedal down further the front brakes start coming on and if you push all the way to the floor the truck will nosedive and you will get planted in the windshield.
I wonder if the aftermarket Bronco Graveyard proportioner valve is blowing all the pressure to the rear wheels because it won't do it if you take the vacuum off of the vacuum booster. You have full pedal when the booster is deactivated and all the wheels operate normally with the exception of having to plant both feet on the pedal to stop it.
Ford Brakes/Suspension :: 2002 - Pedal Sinks To Floor?
yesterday i gave the 02 diesel a treat, 3 new calipers 4 new rotors, and semimetalic pads. the reason for only 3 calipers is the driver side was just replaced 2 months ago after it locked the wheel up on me. both rears were seized so i only had front brakes, and the passenger side front was leaking.
anyway, all new parts and the pedal is fantastic, besides the truck stopping again. this afternoon on the way home from the shop i stopped at a red light. breaks are rock solid. then all of a sudden, the pedal slowly sinks to the floor. but the brakes still hold. i get home and test them. again, pedal slowly sinks to the floor, but they hold. i am thinking still some air in the system, and park hte truck, with the intention of bleeding them again tomorrow.
i get out and see fluid all over the driveway. great. something in the front of the axle is leaking. the frame is drenched. whatever it is, is in front of the frame, on the engine side. what is in there, the ABS unit?
Ford Brakes/Suspension :: 1992 F250 - Brake Pedal Goes To Floor
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 RepliesFord Brakes/Suspension :: 1979 F250 - Hardly Stop When Pedal All The Way To Floor
My problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 RepliesFord Brakes/Suspension :: Brake Pedal Fades To Almost The Floor With Little Pressure On It
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 RepliesFord Brakes/Suspension :: 1987 F350 - Brake Pedal Moving To Floor?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cylinder need rebuilding or is my vacuum diaphragm going. Not sure that's what its called.
View 7 RepliesFord Brakes/Suspension :: 1987 - Brake Pedal Slowly Going To The Floor - Master Cylinder?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 RepliesFord Brakes/Suspension :: 1977 F250 - Brake Pedal Goes To The Floor And Sticks When Running
When depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 Replies