Ford Brakes/Suspension :: Brake Pedal Goes All The Way To The Floor
My dad is having problems with his truck, brake pedal goes all the way to the floor even after bleeding all the brakes and the master cylinder. The wheel cylinder didn't have clips in it and he fixed it and it hasnt changed. What do we do? Its a 1993 f150 4.9l.....
View 4 RepliesFord Brakes/Suspension :: 1992 F250 - Brake Pedal Goes To Floor
My buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 RepliesFord Brakes/Suspension :: Brake Pedal Fades To Almost The Floor With Little Pressure On It
I am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 RepliesFord Brakes/Suspension :: 1987 F350 - Brake Pedal Moving To Floor?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cylinder need rebuilding or is my vacuum diaphragm going. Not sure that's what its called.
View 7 RepliesFord Brakes/Suspension :: 1987 - Brake Pedal Slowly Going To The Floor - Master Cylinder?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 RepliesFord Brakes/Suspension :: 1977 F250 - Brake Pedal Goes To The Floor And Sticks When Running
When depressed the break peddle is firm, when released break peddle does not return, replaced mc and booster, bleed breaks. Still having same problem.
View 1 RepliesFord Brakes/Suspension :: Hissing Sound Each Time As Depressed Brake Pedal Sank To The Floor
Brake pedal to the floor... And a lot of fluid on the ground.
I was coming home (empty fortunately) last evening when I noticed the brake pedal give an initial resistance, then slowly sank all the way to the floorboard when slowing down to turn onto my street. When I got to the house, I noticed a hissing sound each time as the depressed brake pedal sank to the floor. When I got out, there was a lot of brake fluid on the ground on the left rear side. It appears to be between the fuel tank and frame rail. From the side it is the section between the fuel filler to just ahead of the left rear wheel. The tank and frame rail is drenched and dripping DOT 3.
I am lucky to not have been pulling my 5th wheel when this happened! However, I have a camping trip coming up in a few weeks, but now my TV is broken. What has happened, and an estimate for repairs? Where is the best place to have it fixed, dealer or specialty shop? I just bought this vehicle in January and it has 102,500 miles, and came complete with full and meticulous repair records. The P.O. was incredible at upkeep, so this is something curious and flukey to me. But do I need to worry about the other side now, too?
Ford Brakes/Suspension :: 2001 F350 - Brake Pedal Go To Floor As Pressure Is Applied - Bad Master Cylinder?
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 RepliesFord Brakes/Suspension :: 2002 - Pedal Sinks To Floor?
yesterday i gave the 02 diesel a treat, 3 new calipers 4 new rotors, and semimetalic pads. the reason for only 3 calipers is the driver side was just replaced 2 months ago after it locked the wheel up on me. both rears were seized so i only had front brakes, and the passenger side front was leaking.
anyway, all new parts and the pedal is fantastic, besides the truck stopping again. this afternoon on the way home from the shop i stopped at a red light. breaks are rock solid. then all of a sudden, the pedal slowly sinks to the floor. but the brakes still hold. i get home and test them. again, pedal slowly sinks to the floor, but they hold. i am thinking still some air in the system, and park hte truck, with the intention of bleeding them again tomorrow.
i get out and see fluid all over the driveway. great. something in the front of the axle is leaking. the frame is drenched. whatever it is, is in front of the frame, on the engine side. what is in there, the ABS unit?
Ford Brakes/Suspension :: 1979 F250 - Hardly Stop When Pedal All The Way To Floor
My problem, Brakes. I hardly have any at all (pedal all the way to the floor and hardly stop), yet the front pads are dragging, and heating the rotors. Maybe a bent line? I bled the fronts, and as soon as I loosened the bleeder nipple, a good bit of fluid came out, without pressing the pedal of course. It's dark out now or I would inspect for bent lines. Could there maybe a problem with the booster?
View 6 RepliesDodge - Suspension - Dakota :: 2001 - Brake Pedal Goes Almost To The Floor While Braking?
My brake pedal goes almost to the floor when I'm braking.I replaced the rotors, pads, shoes, power booster and the master cylinder 3 times.Had it bled twice and I still have a soft pedal, but now it firms up a bit as I pump the brakes.
View 7 RepliesFord Brakes/Suspension :: 1997 F150 - Brake Pedal Keeps Fading
I recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
Ford Brakes/Suspension :: 1986 F150 - Lose Brake Pedal?
86 f150 4x4
brake pedel goes straight to the floor but if u give it short pumps of the pedel it grabs but barley....master cylinder or the booster?
Civic - Honda :: 2002 - Brake Pedal Sometimes Go To The Floor While Applying Brakes
I have a 2002 Honda Civic EX 1.7L. Recently the brake pedal would sometimes go to the floor when I'd apply the brakes. The car would still stop, but not as quickly as normally. If I apply the brake and it goes to the floor I would release the pedal and reapply the brake and it would stop at it's normal position and the brakes felt firm and the car would stop fine. I was told my problem was the master cylinder so I bought one on Sunday and replaced it. I bled the lines and it seemed like all the air was out. The brakes worked great and the pedal stopped in the same place and was firm.
Now today on my way to work the pedal went down a little farther than normal during one stop. On the way home it stopped in different places. The brakes would always grab and the pedal felt fairly firm wherever it stopped. I drove it this evening again and the pedal went to the floor like with the old master cylinder. One pump and they grabbed in the normal spot. What is going on? Did I not bleed the lines well enough? Is the new master cylinder just junk? I saw in the manual that air can get trapped in the ABS sensor, but an air bubble problem should just make the pedal squishy, not change where it grabs, right? I'm stumped and I really don't want to take my car in if I can fix it.
Saturn - Aura :: 2008 - Brake Pedal Goes To The Floor Before Brakes Engaged
I have replaced the front rotors, calibers, pads and brake lines. I went through the process of bleeding the brakes by using the following sequence: right rear, left rear, right front and left front.
I did this about 4 times - process was to pump the break until the pedal was hard then my son kept his foot on the pedal while I release the bleeder value. During this process I kept the master cylinder full.
Took the car out and the pedal went right to the floor when applying the brakes. The car did stop but not as I had expected. So what have I done incorrectly here? Is there something else to check?
Ford Brakes/Suspension :: 1999 E350 - Anti-lock Brake Pulse In Pedal At Low Speed Light Braking
I have a '99 E350 van that I am feeling a light anti-lock brake pulse in the pedal when I am rolling to a slow stop under light braking. Braking doesn't seem to be affected, but it doesn't feel right. I tried locking up the brakes and didn't feel any anti-lock pulse...seems backwards.
View 1 RepliesFord Brakes/Suspension :: 2003 F250 - Brakes Are Spongy Or Go To Floor
Brake issues 2003 f250 super duty 6.0. Changed master cylinder, drivers side rear brake hose, new pads all around. Pedal is good at times for a few seconds. I've bled them all numerous times truck running or not flushed power steering pump new fluid. Brakes are spongy or go to floor. Do I need a scanner?
View 2 RepliesFord Brakes/Suspension :: After Pressing Pedal Resistance Became Really Soft And Brakes Very Sensitive
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 RepliesFord Brakes/Suspension :: 1997 F250 - Hard Pedal / No Brakes Intermittently
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 Replies