Subaru - Forester :: 2006 - Shifting Extremely Hard When Engine Is Cold
For longer than I'd like to reveal, my Forester has shifted extremely hard. This happens only when the engine is cold and disappears entirely once it heats up. Also, the RPMs go high just before the shift. When it does shift, it feels as if the engine is going to self-destruct from the sound and rough feeling --as if the entire engine or at least some part of it were going to fall to the ground. After it shifts, it feels as if the car shoots forward like a rocket. The Subaru dealer changed the transmission fluid and reset the computer. The problem persists.
View 1 RepliesFord Excursion :: Hard Cold Start And No Heat
I just bought an 03 Ex that hadn't been driven but 600 miles the past three years. Needless to say, there's probably some sludge causing issues somewhere. I have a Scangauge installed, which has been very useful thus far.
I've flushed the coolant, currently with distilled water, changed the oil and filter, atf and filter, and installed my 2nd set of fuel filters after getting stranded after I ran my first tank of fuel through it. After changing the fuel filters the second time, I was still having cold starting problems, requiring 3-4 long cranks before firing. Once warm, runs fine. I just installed a FICM from Diesel Tech Ron, but I still have to try 3-4 times to get it to cold start, then it runs and starts ok. Not sure why the hard cold starts...
Also, the heat doesn't work. A/C is fine, blower is working. I installed a new thermostat, and like I said, I have flushed the coolant with tap water and now distilled water, but didn't want to pour in fresh coolant just yet, in case I have to drain it again with this heat issue. That vc7b is not cheap. Tonight I drove the truck about 20 miles and my highest temps for EOT was around 215 and ECT was 205. Fluctuated between the the mid 190s to low 200s most of the time, this was over some hilly roads with no load or anything. Anything else I can monitor or check on in the mean time?
Ford - ZX2 :: 2001 - Hard To Start / Feels Like Not Getting Gas Upon Cold Start
I've been driving my wife's 2001 Ford ZX2 for the last ~9 months.
Early on in taking over driving it I noticed that it was difficult to start, so I had the battery checked. One place said it need to be replaced, but I wanted confirmation so I had it checked at two other places--it was in the normal range. So then I thought it probably needed a tune up since, as far as I know, it had never had one (has ~50K and I know it should've been done earlier). But, that didn't seem to fix it either.
I then had the fuel filter replaced. Nothing. I generally turn the key over for a few seconds before I actually crank it to let fuel in. It is now taking 3 times each startup to do this. And, right after starting it feels like the car is struggling to get gas (as if the fuel filter is completely stopped up or a fuel link is kinked).
Once the car is warm it cranks over on the first time (as if nothing is wrong). The last time I was at the shop they told me I need to have my fuel injection system cleaned. I have doubts about this--they based it on mileage not any sort of actual diagnostic or inspection. I use quality gas and run a fuel injector cleaner at each oil change.
Passat (B5) :: 2002 - Brakes Extremely Hard On Cold Mornings
I have a 1.8 02 Passat. On cold mornings (25 or below) the brakes are extremely hard. When it warms up outside they are fine. No one seems to know the problem.
View 16 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Parking Brake Pedal Is Extremely Hard To Push
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesFord - Explorer :: 2000 Won't Idle When Cold / Hard To Start And Keep The Engine Running
I have a 2000 Explorer W/4.0 SOHC engine. With summer nearly over and fall on the way, I need to figure out what is going on with my engine. This problem has been going on for the past 2 years. As the outdoor temperatures get cooler, the harder it is to start and keep the engine running. This starts happening around 65 ambient temperature, and gets worse as the temps drop. By 30, I can barely keep the engine running.
Odd thing is, all I have to do if the engine starts is, keep my foot on the pedal to keep the engine around 2000RPM, put it in gear and start driving. After about a mile or two, the engine runs normally, and will do so the rest of the day. So far I have cleaned the air flow sensor, replaced the IAC, replaced all the injector "O" rings, and cussed a lot. I smoke tested the engine and the only vacuum leak is a very small one at the EGR valve.
Ford Excursion :: Engine Temperature Act Quite Normal After A Cold Start / Won't Get Warm
I have a problem here which isn't funny around 30F. The engine temperature act quite normal after a cold start, but the heating inside is disabled somehow. So I can select any temperature in the front and back, but it stays cold.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 - Hard Start When Engine Cold
2003 F350 7.3L 164k miles. Got towed in with hard to start cold complaint.
Hooked it up to the Snap On Verus Pro scan tool and we get up to 3000 psi on the ICP cranking, IPR value seems within spec, we have rpms over 100 on tool, pulse width within spec, computer voltage above 10v while cranking, verified output of glow plug module (California) and glow plugs get voltage for approx 50 seconds @ 80 degrees farenheit, glow plugs all read 0 ohms resistance.
injectors do NOT sound the same during buzz test.
Vehicle takes EXCESSIVE cranking cold to eventually get it started. LOTS of cranking. Just had to replace starter and a battery because driver burned em out. It feels like the vehicle shakes when it gets running. Black smoke when revving cold. Sometimes white smoke while cranking.
Once the engine has been warmed up, it starts perfectly every time.
I have spent two days in the engine bay looking for chaffed wires and doing diag and my current diagnosis is bad injectors. I feel there COULD also be high pressure oil leak, or a mechanical issue such as low compression. No compression guage yet for this truck. We have the ICP and IPR fittings to do a shop air test. Recently did a 6.0L and went thru everything and eventually diagnosed it as bad HPOP. LOW ICP pressure.
I noticed two of the cylinders were at maybe 8% Perdel on the data. Seems too high. Also, it "passed" the KOER self test and "passed" the injector buzz test with no codes after, but the audible sound of injectors didn't "seem" right to me, but I am new to these engines.
Santa FE SM (2001-06) :: Hard Start After Short Trip On Cold Days Only
I have an issue for the last couple of years. I drive a 2006 hyundai santa fe with 168,000 km's on it. the problem I am having only happens on any cold day and never above zero celcius and when I start the vehicle on a cold day and go for a short trip to the store run in for about 5-10 minutes and I come back out and it won't start, there is lots of power but it wont roll over at all but after trying many times it will eventually start and there is no CEL showing and I have never plugged it in on a cold day and as cold as the canadian winters get here its been down to as low as -40 in the morning and no problems at all, a little roll and a groan and away she goes which is typical in our cold climates.
View 5 RepliesSanta FE SM (2001-06) :: 2005 V6 Transmission Jump Hard And Bucked On Cold Start
I own 2005 Santa Fe. Vehicle is a 3.5l V6. 90,000 miles. Transmission flushed few months ago. Few weeks ago I notice that transmission jump hard and bucked on cold start then smooth out once the engine warm up. Is it normal? if not what could be a problem.
View 3 RepliesTiguan :: Misfiring On Cold Start - RPM Goes To 1100 And Engine Works Hard
For last 3 months I have faced to a problem. My 2009 2.0 TSI, misfiring in cold start (in Summer!). When engine is cold (particularly in the mornings) in FIRST start, RPM goes to 1100 and engine works hard and car badly shakes. If I continue, engine light flashes. But if I just after first start, turn off the engine and restart it again, RPM comes back below 1000 and engine works well!!.
During first start a strange noise comes from the below of the car (Check...check...check...) but in second start everything is OK.
KM is 100k. I red the code and it usually shows P0302 (Misfire in cyl 2) and sometimes P0301 and P0300. I recently change all spark plugs (ngk) but problem had started before sparks change.
I switched the coils to see if misfiring follows the coil but negative.
I know it can have different reasons, PCV, carbon build up, EGR,..... but as it goes just after SECOND start I think it should be an electrical problem.
Chevrolet - 1500 :: 1996 Chevy Engine Hard To Start When Cold
I have a 1996 Chevy Cheyenne pickup with a fuel injected small block that has 50k miles. Earlier this summer the truck developed a problem where it is very hard to start when cold (after sitting overnight or after sitting for many hours on my flat driveway). When the engine is cold (say the first start of the day) I can only get it to start by giving small bursts of cranking power to the starter. That is, it won’t start if I hold the key in the cranking position but is more likely to start if I give it a short burst of cranking power (when I hold the key in “start” position) for a second or two.After the first start of the day, the engine runs fine and subsequent starts are quick and normal. The “Check Engine” light is not on and there are no trouble codes…. Other than hard starting there are no issues with engine performance.
View 2 RepliesChevrolet - Suburban :: 1998 - Engine Hard To Start When Cold Outside Or After Rain
I have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 RepliesFord Excursion :: Hard To Shift From Park While Running In Cold?
As it's progressively grown colder (which may or may not be related), my truck has grown all but impossible to shift from park into reverse neutral or drive with the engine running when the truck is cold. I often have to shut the engine off, and once I do it immediately is very easy to shift out of park into neutral, and then I can restart the engine. Once the truck has been driven some, it's not hard to get out of park, but if it's shut off for some time (an hour maybe) it will be difficult to shift out of park again. I don't know how to begin troubleshooting this.
View 8 RepliesFord Super Duty (1999-2016) :: Hard To Start When Cold - White / Grey Smoke At Start Up?
Truck: 1999 Ford Truck F 350 4WD Super Duty V8-7.3L DSL Turbo VIN F
Problem: Especially when it is cold outside . . . The truck takes forever to start and while doing so a ton of white/grey smoke comes out of the exhaust.
My starting schema: Turn the key on have the gas pedal pushed to the floor until the "wait to start" light goes out. Then, I turn the key off and back on while still pressing the gas pedal all the way down. When the "wait to start" light goes out again I remove my foot from the pedal and try to start it. I never leave it cranking for more than 5-7 seconds. If, after trying this process several times I will not push the pedal in at all. Also, sometimes I will leave the pedal pushed in while I am cranking it over.
The truck used to start after a couple of tries but lately it won't start at all, even after 20 tries. Sometimes it will spin up for a second as if the engine gets going but then just doesn't continue running. When it is warm out it will usually start after a few tries but doesn't seem normal to me. After I first bought the truck(used) it would start up within half a second after turning the key.This all started after I had to fix an o-ring that was damaged on the top/back of the motor that was dumping all my oil out of the top/back of the motor.
Golf V R32 :: Extremely Jerky Start Up In First Gear When Very Hot Out And Engine Warmed Up
I need to have my DSG checked out.. Extremely jerky starting out in first gear when very hot out and engine warmed up --most noticeable when just easy on the accelerator. Need to get the ok for mechanotronic replacement. Who to trust for a reliable job and evaluation of the problem.
View 3 RepliesSanta FE SM (2001-06) :: P0335 And P1372 - Engine Goes Into Limp Mode And Very Hard To Start
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
Santa FE SM (2001-06) :: Hard To Start After Fill Up - Rough Idle And Engine Shuts Off
Every time i stop for gas..my 01 santa fe is hard to start..it would take 4 to 5 start before she goes, then i have to keep the rpm up, bring her to idle..after that shes ok, till the next fill up.. the only way around this is to keep her running while gassing up..while filling up she run rough idle, some time engine shuts off..then its hard to start..
View 5 RepliesFord Excursion :: 2004 - Hard Start When Warm?
I got a new to me 2004 4x4 Excursion v10. 98,000 miles but why it is hard to start when the engine is warm. Starts right up when cold, engine not ambient air temp, idles great once started. In park idles at 1,000 until normal op temp is reach, then down to 750ish. In gear idles right at 650. Drives great. Plenty of power, does not surge, averaging 13.7 mpg over two tanks (70% hwy, 30% city) and no codes. Since it is new to me, and I don't trust people to do maintenance I have:
Replaced spark plugs
Replace downstream o2 sensor (the two upstream were not in stock)
Replaced fuel filter
Replaced belt
Replaced crank sensor (because the belt was already off)
Changed oil (mobile 1 5w20) and filter.