Ford Brakes/Suspension :: Bolt Stuck In Leaf Spring Bushing
I am replacing my rear leaf spring hanger and shackle. I have one side done and the other side the old hanger is off. I am ready to install but the bolt/ bushing in the leaf spring will not come out. I tried every thing with what i had for about 2 hours. Is there a tool to remove these things similar to a ball joint press.
View 14 RepliesFord Brakes/Suspension :: Replacing Shocks / Bushing Completely Seized Up To The Bolt
I made a thread in the F150 section but maybe it should have went here. Anyhow I'm replacing the front shocks on my 99 150, and well the bushing was completely seized up to the bolt on the bottom of the shock and I ended up breaking the one side of the shock mount off with it. I can't see any easy way of getting it off, I fear I might run into the same problem with the other side.
Would it be ok to just bolt the new shock back on, sans the forward mount? If its just bolted through the rear bolt hole will there be too much play? I really don't feel like replacing the whole lower suspension arm on this beater truck, and I dont think my welding skills are up to that. I don't think my little stick welder even has enough heat.
Ford Brakes/Suspension :: 1998 - Rear Brakes Split In Half - ABS Getting Stuck?
Two months ago, I replaced the rear drum shoes, wheel cylinders and seemed after that I was ok until today. I checked the rear brakes and they are split in half. i noticed my abs & brake lights lit up this morning. I would think the ABS is getting stuck? How do I check the ABS? This morning I felt like something was holding back the truck. I continued and when I got home I said to myself, let me just check the rear brakes and thais what I found. Both sides had the shoes broke.
View 1 RepliesFord Brakes/Suspension :: Steering Wheel Wobble Back And Forth About A Half Inch Or So
I have a 1993 f150. Problem is that the steering wheel can wobble back and forth about a half inch or so. I took the wheel off and it looks like there is a lock ring holding everything in place. I just wondered if there was a solution to this to fix it
View 1 RepliesGolf V R32 :: Should Have Spacer To Clear Brakes And Prevent Rubbing?
Just picked up some VMR V701 18X8.5 with a 45 Offset in Gunmetal. Do I need Spacers to clear the brakes and prevent rubbing for the front and/or rear? If so, how many mm?
View 4 RepliesPassat (B6) :: 08 - Center Bar And RHS Clip Cracked In Half In Hot Sun
Yesterday, I tried to use my rear window roll-up sun shade while parked in the hot sun, pulled gently up on the center bar, and the RHS clip ---which rides in the tracks along the C-pillars---cracked in half!
08 Passat Owners, the rear roll-up sun shade (NOT the rear door shades) on your car is very fragile! VW uses some kind of lexan plastic molded insert which fits into the tracks. Any out of plane stress on the fittings will damage them, rendering the entire shade useless. Luckily my dealer had a new fitting in stock and the repair was made in less than 10 minutes.
Santa Fe (CM - 2007-12) :: Front Suspension Squeak Noise / Rubber Bushing Is Broken
For some months, I've heard squeaking noise from passenger side suspension. Sound like it's from shock & spring on bump road.
This video sound is very similar : Squeaking Noise, Front Driver Side - YouTube ...
I looked at my suspension. and found rubber bushing is broken. Driver's side bushing is normal.
Is this noise related to the broken bushing?
Is it easy to replace the rubber by myself?
A guy said ATP AT-205 reseal will fix this noise in Youtube video. Is it true?
How To Fix Squeaks In Your Car - YouTube ....
Ford Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Ford Brakes/Suspension :: F150 - Rear Brakes Lock Up Upon Hard Braking?
What would cause the rear drum brakes to lock up upon hard braking? I have replaced the wheel cylinders, installed new spring kit, and adjusters.
View 9 RepliesFord Brakes/Suspension :: Brakes Does Not Feel Soft / Truck Is Hard To Stop
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
Ford Brakes/Suspension :: 1994 F250 - Blown Brake Line / No Brakes At All?
I have a 1994 F-250 4x4 w/manual transmission. I was driving a few days ago when the brake pedal suddenly went to the floor. I had almost no brakes (less than 10% at most), but luckily was able to get off the road safely. It was immediately apparent that the line connecting the T-fitting and the passenger side drum had broken.
I have never blown a brake line before, but I always assumed that you would have either front or rear brakes, depending on which line blew. Unfortunately I was wrong! The master cylinder reservoir was about 3/4 full when I initially checked it, but after I moved (slowly) the truck to a safer spot in the parking lot, I checked again and it was nearly empty.
Is my brake system behaving normally (no brakes front or rear, blown line completely empties the reservoir), or should there be some safety factor built in? If the system is operating correctly, is there any way to convert to a system that doesn't give out fully when a line is blown?
Ford Brakes/Suspension :: 1995 F250 Truck Does Not Stop Fast Enough When Hit The Brakes
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
Ford Brakes/Suspension :: After Pressing Pedal Resistance Became Really Soft And Brakes Very Sensitive
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 RepliesFord Brakes/Suspension :: 2005 F250 Front Brakes Calipers Are Locking Up
I have a 2005 F250 & both front calipers are locking up. I have replaced the front pads, no change, my mechanic installed a new master cylinder. No lockup for about two weeks until today. Front calibers are locking up again.
View 1 RepliesFord Brakes/Suspension :: 1997 F250 - Hard Pedal / No Brakes Intermittently
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesFord Brakes/Suspension :: 1996 F350 Pulling To The Left When Apply Brakes
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
Ford Brakes/Suspension :: 2003 - Lost All Power Brakes / Steering?
Yesterday while driving, i lost all power steering and power brakes (you would automatically think Booster). I pulled over, popped the hood and fluid was spewing from behind the power steering pump somewhere. I limped the truck home about 20 miles. I checked brake fluid and it was full. checked power steering fluid and it appeared to be empty. Yet when i added fluid it took less than a half quart. I started the vehicle to pressurize the pump and find the leak. Yet the pump never pumped any fluid. (one would thing pump was out) I am baffled as to if the pump went out, why fluid loss? If the booster was out, why do i still have brakes just without power assist? Andif a hose is blown, why such small fluid loss? I dont want to just start replacing parts till it get the right one
View 1 RepliesFord Brakes/Suspension :: Smell From Brakes And Left Front Rotor Hot
My 97 f150 had been sitting for a while and after a few miles I could smell brakes and the left front rotor was hot. So I removed the caliper to see if I could free it up. When i push 1 piston in with a C clamp the other one comes out and visa-verse but I cannot push both in with 2 C clamps. When I push the brake pedal they both come out. Its like there is a check valve in the line. How should I go about trouble shooting this?
View 1 RepliesFord Brakes/Suspension :: 2003 F250 - Brakes Pedal Pulsed A Bit
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 Replies