Ford Brakes/Suspension :: Jacking Directly On Torsion Bars But Not For Leveling?
Just wondered if can use a floor jack to lift a vehicle but jacked directly on the torsion bar? Or let the vehicle rest on the torsion bar on a jackstand?
I have done this a few times with different vehicles and I guess didn't really think hard about it damaging anything, but was curious...
Ford Super Duty (1999-2016) :: Truck Not Sitting Level / Slightly Leaning To One Side
I noticed my 16 ccsb 4WD lariat 6.2 was slightly leaning to one side in a parking lot yesterday. My driveway at home is dirt and far from level so I would never notice at home. So before I pulled out of the parking spot I got my tape measure out. I've got 41.5 inches from ground to top of wheel well on the drivers side rear. On the passenger side rear I've got 42.25 inches from ground to top of wheel well.
So darn it the truck is 3/4 inch leaning to the driver side. Is this normal? I can understand it not being exact to the millimeter however 3/4 inch seems to me like a lot of tolerance. The bed was empty when i measured and Air pressure in both rear tires is 70psi. I did pull a load with about 2,000 pounds tongue weight the other day however that shouldn't make any difference.
Ford Brakes/Suspension :: 1996 F350 Pulling To The Left When Apply Brakes
1996 F350 PSD 7.3
Front Dana 60 mono beam
4 x 4
Last week I broke my front right caliper. I replaced the caliper, rotor and pads. Now, when I apply the brakes I pull to the left. I took the truck into my repair shop and let them figure it out. They were unable to repair the truck. They replace the master cylinder, all brake lines, calipers on both sides, brake pads, bearings on both wheels, vehicle alignment, tire balancing and tire rotation. The tires are three months old. Prior to last week i did not have any problems braking or steering. Driving at 60kmh the truck goes straight until i gently brake, it will slightly pull left.
Ford Brakes/Suspension :: 2003 F350 - Changing Front Brakes / Have To Remove Hub Or Lockouts?
I've changed brakes on tons of front wheel drive cars, and two wheel drive trucks. But NEVER on a 4wheel drive Super Duty. My truck needs new front brakes now!!!! its a 2003 F350 4X4 -58,000 miles. I was just wondering from you all, how hard is it to change brakes on a 4x4 truck? Do I have to remove the Hub or lockouts?
View 5 RepliesFord Brakes/Suspension :: 2003 F350 - All 4 Brakes Dragging
Here's the deal:
* Drive the truck after it's been sitting a while (overnight, or at least a couple of hours), everything's fine. Good brake pedal feel.
* Drive 10-15 miles, stop-and-go at lights and stop signs, the brake pedal slowly goes from normal to firm, to very firm. Then, no play whatsoever and brakes are dragging bad. Yesterday, they were dragging so bad that I had it pulled into 1st gear with pedal on the floor just to get thru an intersection.
* Get out and check each wheel, all 4 brakes are dragging. I can tell from the heat pouring out of each wheel. And I've verified with infrared thermometer. Also, I've raised the vehicle when this is happening, and all 4 wheels will not turn. So it's definitely all 4 brakes.
At first, I assumed it was seized slide pins. But I've THOROUGHLY cleaned each and every one, and lubed with synthetic caliper grease. When the brakes are feeling normal, I've had my wife pump the brakes while I watched the calipers. Near as I can tell, they slide easily. Again, when my problem happens, it's all 4 wheels SIMULTANEOUSLY. So I've pretty much ruled out slide pins.
The brake pedal itself isn't getting bound by anything. It moves freely and I've lubed each of the pivot points. No problems there.
* When the brakes are dragging, I can crack the bleed screws and some fluid will come out at each wheel, which releases the brake at that wheel and I can then turn each wheel freely. So, there's residual pressure in the lines. I replaced the master cylinder (twice actually). No change in behavior.
BTW: I thoroughly bled the lines after each of the two master cylinder changes. I must've put 60+ ounces of fresh/clean/new fluid into the system so this isn't related to old fluid.
* Next, when the brakes are dragging, I can unscrew the master cylinder about 1/8-inch or so from the booster, and the brakes immediately release. Again, indicating residual pressure in the lines. So, I assume that something funky is going on with the brake booster. Also, when the brakes are dragging, I can pull the vacuum hose from the brake booster. And after a few seconds the brakes release. So I installed a new brake booster (re-manufactured one from NAPA -- they didn't offer a brand new one). No change in behavior.
After swapping the brake booster, I can still pull the vacuum tube when the brakes are dragging and it'll release in just a few seconds. So, it really seems like something is going on with the booster, but I can't figure out what it might be.
It is possible for the brake booster vacuum tube to have TOO MUCH vacuum, thereby causing the brakes to be unknowingly applied? Is there maybe a regulating valve of some kind in the line?
Ford Brakes/Suspension :: Brakes Does Not Feel Soft / Truck Is Hard To Stop
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
Ford Brakes/Suspension :: 1995 F250 Truck Does Not Stop Fast Enough When Hit The Brakes
My truck sat for 4 years. 1995 F-250. We needed to replace the brake lines. when you hit the brakes the truck does stop but not fast enough and it will not pass inspection this way. So far I've replaced
1. All the brake lines
2. Calipers
3. Brakes all around
4.RABS module
5. Master cylinder
6. Wheel cylinders
Pretty much everything but the brake booster. Lines were bled several times. The brakes still go to the floor. Anything else that I haven't tried? I want my truck back!
Ford Brakes/Suspension :: Front Brakes Are Dragging / Does Not Stop The Truck Just Gets Hot
First it was the RH now after replacing the rotors, calipers and new shoes. The LH is now doing it. It doesn't stop the truck just gets hot, the wheel, and u can smell it. The truck is a 97 f150 ext cab 2wd short box, had since new and has over 200,000 miles and going strange until now. I want to get 300000.0 before I let her go. Had to replace a rear axle brake line years ago, and do not think the lines were bleed right, the brakes never work just right.
View 4 RepliesLexus GX 2010+ :: Air Suspension - Left Side Of Truck In The Back Sitting About 1.5 Inch Higher Than Right Rear
ok, its been 9-10 months now, and i have only 3500 miles on my gx.just looked at the back wheel wells.
The left side of the truck in the back is sitting about 1.5 inchs higher than the right rear? I measured the distance between the rims and the edge of the panel in the back. I am baffled. I raised it, lowered it, and still unequal height. Its going to the dealer on wednesday.
Ford Brakes/Suspension :: 2006 F250 - Rattling After Doing Brakes / Emergency Brake And Rear Wheel Bearings
Before I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
Ford Brakes/Suspension :: 2018 F350 Hard Ride - Normal?
just bought 2016 f350 6.7L super duty,super cab,now has 3000 miles on it,question is it ride hard is that normal and can i get it to ride smoother
View 6 RepliesFord Brakes/Suspension :: 1979 F350 - Master Cylinder Replacement?
I was wondering if there was how to on doing the MC replacement? The brake pedal goes to the floor almost every time you press on the brake?
View 1 RepliesFord Brakes/Suspension :: 1999 F350 - Caliper Won't Release Fully
I have a 1999 F350 single rear wheel Superduty truck that will not allow the right rear caliper to fully release. I replaced the caliper/mounting hardware/pads/rotor. The problem continued so I replaced the rubber hose to the caliper. Problem continues. I'm thinking possibly the center rubber brake line at the differential (where it splits and goes right/left) but at this point I am guessing. Maybe proportionate valve but I know nothing about them.
View 11 RepliesFord Brakes/Suspension :: Cracking / Metal Stress Sound From Under Truck
I have a '06 F150 King Ranch with a after market lift. I sometimes hear a cracking, metal stress sounding noise from under the right side under carriage, I thought is was my brakes or shocks or something. If I take a right turn down an angle while braking or it happened during a rainy day going straight at a slight downward incline during braking, there's a knocking like pac..pac..pac..pac sound from under my rear or sometimes front passenger side fender well. I've taken it to a brake specialist and had it inspected by a mechanic, but no visible signs of a problem. What this might be? I told my brake specialist to check my anti lock system as the sound is evenly spaced and he said nothing is wrong.
View 1 RepliesFord Brakes/Suspension :: 1989 F350 4WD - Steering Shimmy / Front End Bouncing
Truck is an 89 single cab, single rear wheel F350 4x4 with 7.3 non turbo diesel and a c6 trans. not lifted, stock size tires. If you hit just the right bump, regardless of speed, the front end just goes crazy.. tires and wheel shoot violently side to side and its very frightening/dangerous. you can just barely hold the wheel, front end is bouncing and whole truck shakes from such rapid camber change as the contact patch swaps from inside to outside of the tread.
Tie rod end, draglink, steering stabilizer (add on,) shock absorbers (rancho,) and a wheel bearing are all brand new. With each part replaced the shake felt worse (since more of it was transmitted to the steering wheel rather than lost in the sloppy parts) and i took it off the road immediately.
Brand new steering box, put it back on the road, did it again less than a mile away. It rained all day so i haven't jacked the truck up again and really, I am quite sick of this problem.
Ford Brakes/Suspension :: 1987 F350 - Brake Pedal Moving To Floor?
1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cylinder need rebuilding or is my vacuum diaphragm going. Not sure that's what its called.
View 7 RepliesFord Brakes/Suspension :: 1997 F350 - Driver Side Rear Brake Hot
Last weekend I did a rear brake job on my 1997 F350 4wd diesel. I replaced the shoes, replaced all the hardware, replaced the cylinders and had the drums turned. I have driven the truck all week and everything has been fine. Tonight while out of town I set the parking brake to see if it was any better since the rebuild, and it was. Shortly after releasing the parking brake I drove about an hour to get home. When I arrived home by driver side rear brake, wheel, etc. was very hot. I threw water on it and it turned to steam instantly.
I suspect that setting my parking braked hard like I did (like you're suppose to) somehow caused it to drag. What is causing this and what needs to be done so that it doesn't happen again?
After reading some other posts I went out and checked my parking brake cable and found that it is not bound up that I can tell. Perhaps it did not completely release although it seems to release just like the other side. I checked it from front to equalizing bar and it is in great shape. The plastic coating is still on the wire and there isn't any corrosion the entire length. The only thing I did differently on this trip vs the one I made two days ago was try out the parking brake before I left. The last trip I could barely feel any heat on the rear wheels when I got home, this time the driver side was scorching hot.
Ford Brakes/Suspension :: Truck Badly Pulls Left When Braking Hard
Just replaced break pads and rotors. Inner pad on left side was gone leading me to believe slides were not working properly. Pulled apart, cleaned and greased everything, and replaced pads and rotors. Calipers seem to be working fine. Now when I break hard, the truck pulls badly to the left. When I break softly, it seeks normal. My front end is a bit out of whack and veers just a bit to the left. Do you think this is my issue with the breaking ? I'm getting new tires and an alignment soon but was just curious.
View 3 RepliesFord Brakes/Suspension :: 2000 - Parking Brake Shoes Won't Hold The Truck At All?
I have a 2000 F350 4X4 with a V10 under the hood and a 5 speed manual transmission. It has a heavy western hauler bed, and a dual tired rearend. The truck has disc brakes all the way around that work great. I bought the truck used and immediately replaced all the disc brake pads as well as the seperate parking brake shoes and I had the parking brake drums turned. My problem is the parking brake shoes won't hold the truck at all and never have even when they were new. The parking brake shoes seem very small to me for a truck this size and weight. I have adjusted them as tight as I can with out causing them to drag when they are released. Is this a common problem for this type of parking brake on this type of truck? Is there something I am over looking or need to do to perhaps improve the parking brake? Would it be possible to splice some sort of "locking" valve into the brake lines going to the disc brakes to perhaps hold them engaged when I park the truck? I have a good idea how air brakes work, so I suppose this "locking" valve would work like that except basically opposite of a locking air brake valve, if that makes any sense.
View 14 Replies