Ford A/C :: Hot Air Blowing / Clutch Does Not Engage But The Compressor Does Turn
Says A/C Compressor Clutch Circuit open. A/C blows hot air....go to VENT and the EATC controls the temp fine (ambient air only). It's on a '97 Lincoln Mark VIII if it makes any difference. Pulled code # 1530 ...
Clutch does not engage but the compressor does turn. Also the EATC will NOT go into the test mode. Push OFF and Floor at same time, then AUTO within two seconds. Nothing. Is this a clutch gap problem? New clutch was installed about a year ago.
Ford F-150 - 1997-2003 :: 2001 4x4 - Front Wheels Will Not Engage When Turn The Switch On
When I turn the switch on the front wheels don't engage. I replaced the two vacuum solenoids on the firewall no change. I replaced the actuator motor on the transfer case and everything worked....once. Tried to go around the back of the house thought I was in 4x4 but front wheels not engaging again. buried in mud. I let it set there overnight. Went out earlier started it and put it in 4x4 and it started puling out front wheels engaged. As soon as I gave it a little gas the front wheels became disengaged and it wouldn't go anywhere. I made several more attempts and no luck. I did the vacuum test where you turn the heater on panel and if there's a vacuum leak somewhere the heater blower will default to defrost. It passed this test so I'm assuming there is no leak anywhere. Why it worked right after I replaced the transfer case motor and again only after I got stuck and it set in the mud overnight?
View 2 RepliesFord Super Duty (1999-2016) :: No Outcome When Turn On The Switch On The Dash To Engage 4 Wheel Drive
I have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 RepliesFord A/C :: Clutch Won't Engage
I have a 1999 Winnebago Motorhome on a F53 Ford V10 Chassis and the A/C clutch will not engage when turning on the A/C. I have check the Freon 134A and it appears to be fine (in the red zone) and actually put a jumper across the pressure switch connector (harness side) and it still will not engage. Is there a fuse within the circuit if so, where it may be located?
View 1 RepliesFord A/C :: Clutch Does Not Engage And Compressor Is Not Running
So clutch doesn't engage and compressor is not running. I have 12-13v at the low pressure switch and the same at the high. When I jump the low pressure I don't get any voltage at all at the plug that controls the relay for the clutch.
Where I'm confused is:
Is this a low pressure problem - gauge is reading 60psi on the accumulator
Or
Is this electrical somewhere?
Ford A/C :: EATC - Clutch Did Not Engage When Set On Max Or On Defrost
I recently purchased a 2003 Grnd Marquis that has EATC climate control. It was a cold day, snowing some and the heater was set to 72 degrees on floor/defrost mix. Several days later it warmed up to over 40 degrees so I decided to try the AC. When I switched over to Max AC, I still only got airflow through the defrost. Any airflow setting (floor, vent, AC, Max AC) only gets airflow through the defrost. Also, the AC clutch did not engage when I set it on Max AC or it is not engaged when set on defrost. Will replacing the EATC head unit fix it? Is this also why the AC compressor clutch does not engage?
View 2 RepliesFord A/C :: Clutch Won't Engage - Low Pressure PSI Reading Is Over 85
The patient: e99 F250 Super Duty with 7.3 "Million Mile" motor, 350k miles.
Symptoms: AC won't engage, low pressure PSI reading is over 85, past my needle's capability.
Story: Bought the truck and found a big fat rock hole in the condenser. Swapped condenser and dryer, vacuumed, oiled, and recharged the system. Worked great for 1 month. Now seems any time I turn the truck off or turn off the AC it sends the low pressure soaring above 85 PSI. If I "De pressurize" the system to normal, Turn the truck on, then the clutch engages, and things go back to normal, then below normal because I just depressurized 2 cans worth of the system. Add two cans and it's good to go.
Ford A/C :: 1994 - Compressor Clutch Will Not Engage
I just picked up a '94 7.3 IDI Turbo, and I can't figure out what ails the AC. It appears that there should be enough refrigerant (according to my recharge kit), but the compressor clutch will not engage. I have checked the fuses, and all are fine. All other HVAC functions are normal. Is there a way to test the compressor?
View 5 RepliesFord A/C :: 1996 - Clutch Will Not Engage Intermittently
Sometimes in the morning the AC will work just fine, but after a while it stops working. It looks like the clutch will not engage and I don't know how to troubleshoot it. I'll take a picture later on today. I'm wondering which part is what, and what might be causing the problem.
View 9 RepliesFord - Ranger :: 1999 - Can't Get Transmission To Engage The Clutch
1999 Ford Ranger 2.5L 5 speed transmission. I am a little confused I can not get the transmission to engage the clutch, I replaced the clutch 3 weeks ago, now I have no pressure in the pedal, I have bleed the system 5 attempts with clean solid flow of fluid. What else can I do to fix this or trouble shoot from here?
View 6 RepliesFord A/C :: 1994 - Compressor Clutch Won't Engage / Only Light Goes On?
I have a 94 Ranger with 2.3L motor. Last week my ac quit working. I push the in and the ac light goes on, but the compressor clutch won't engage. I changed the relay, but that didn't work. The fan still works, but the ac does not come on. I tried banging on the compressor pulley, but that didn't do anything. The clutch is not frozen -- it spins freely. The connector looks good and I haven't done any work in the engine compartment so I couldn't have accidentally moved any wiring. What I might try or is my compressor simply dead?
View 2 RepliesFord F-150 (2004-2008) :: 4x4 Doesn't Engage - Codes P0171 And P0174 When Switch To 4LO
Just recently replaced the driver side 4wd actuator. When testing the system to see if it was working, I noticed that in 2wd everything seemed to be in order (wheel spun without the half shaft, no grinding noises on test drive, seemed good to go).
However, when I switched to 4hi, the dash light "4HI" would come on but the wheel still spun freely without the half shaft. When the truck was off, the wheel and half shaft spun together as they should when vacuum is released from the actuator. When I switched to 4lo, the dash light did not come on and the check engine light came on. Pulling codes revealed P0171 and P0174.
Could these codes be caused by a bad solenoid? Is the solenoid not switching the vacuum off and that's my issue? Are there other possibilities?
Ford Transmission :: No Clutch / Truck Will Not Engage A Gear While Running
I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.
View 1 RepliesFord A/C :: Compressor Clutch Making Noise / Would Engage Or Disengage
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 RepliesFord Excursion :: 4x4 Selector Switch On Dash Lights Up Properly But Auto Hubs Don't Actually Engage
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 RepliesFord - Windstar :: 1995 - When A/C Is Turned On Compressor Clutch Doesn't Engage
I have a 1995 Ford Windstar. When I turn on the air conditioning, the compressor clutch does not engage despite having sufficient refrigerant in the system. Jumping current directly to the compressor clutch will engage the clutch, so it's not the clutch. I suspect the relay for the compressor clutch inside the CCRM may be bad, but am not sure how to test it. I have a Haynes repair manual, but how to test this device?
View 12 RepliesFord - Ranger :: 1995 - Clutch Does Not Engage / Pedal Starts To Feel A Little Spongy
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
Ford Ranger / B-Series :: Clutch Start To Engage / Disengage At Half Way Point On The Pedal Travel?
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 RepliesSanta FE SM (2001-06) :: A/C Compressor Does Not Engage When Switch Is Pushed
2004 Santa Fe (GLS 2.7L)
First off, the A/C has not worked since I bought the vehicle used. I have checked all the SMALL fuses (10-25 amp) that can be easily determined good or bad, both under the dash and under the hood, so this basically rules that out (right?). I was unsure of how to check the larger, plug-like fuses under the hood. I am about 85% sure the A/C compressor does not engage when the A/C switch is pushed (yes, the light on the A/C button inside does come on and stay on). This is because I am unsure of which pulley is the A/C compressor and where exactly it is located under the hood. My research showed that it should be the bottom-right pulley when looking at the car from the passenger side, but I could be wrong on this. The fact that I just moved to Florida from the midwest a few weeks ago makes this a rather urgent problem.
Next, after a recent oil change there has been a harsh knocking, diesel-like noise coming from the front-right (passenger) side under the hood. Further inspection seems to show that it is coming from the area of the A/C compressor (or where I'm assuming it is). Again, I'm wondering if this is related to the A/C compressor. This noise is not normal, and has only recently begun to be a problem. It happens during initial startup, can be heard during acceleration, and only seems to quiet down a bit during idling after the vehicle has been warmed up. But it is now always present.
Finally, when fueling I have noticed that filling the car prevents it from starting! I am forced to shift into neutral and rev the car while simultaneously turning the ignition. This does the job, and once the car is started, it runs fine and the problem only ever happens immediately after fueling...any thoughts from the more "mechanically-inclined" out.