Ford 6.7L Power Stroke Diesel :: Truck Has No Power Barley Moves / Codes PO113 And PO4DA
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 RepliesFord 6.0L Power Stroke Diesel :: No Charge / Alternator Is Making Barley Over 12 Volts
I am having a charging system issue. The alternator is making barley over 12 volts. With KOEO the battery light on the instrument cluster does not come on. I have already replaced both batteries and the alternator -before i noticed the battery light is not coming on.
View 2 RepliesFord 6.0L Power Stroke Diesel :: No Power / Bogging Down / Truck Barely Moves
My 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Tachometer Went Below Zero When Got Off The Highway And Came To A Stop Light
2005 6.0L... Driving to work today, doing about 70mph looked down at the gauges and the tach was reading just above 1k the whole time. Even when I accelerated hard.
Got off the highway and came to a stop light and the tach went below zero (almost rested on top of the boost gauge) light turns green goes up to about 1k but no higher even though I stepped into it a bit.
Got to work and turned the truck off and then turned it back on and the tack started working again.
No mods to the truck other then a stereo system attached to the factory stereo wiring harness. I called the stealership and of course they want the truck to look at. I am curious if it is going to work or not on the way home.
Ford 6.0L Power Stroke Diesel :: 2005 - Used PMC Installed Now Tachometer Won't Work?
My mechanic put a used 2005 PMC in my 2004 powerstroke. Now tachometer does not work, trans and coolant temp guages don't work and drives as if it is stuck in 3rd. gear. Does it need flashed @ a ford dealer to sync the two together?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Tachometer Not Working Properly
I have an 06 f250 6.0. When I bought it a few weeks ago I turn the key on and let the glow plugs warm up and start the truck it would start easily. Now it seems like it's taking longer to start . The temperature are between 50 and 80 degrees. I changed the fuel filters and it's still taking to long to start.
2nd I noticed today that when my truck is at idle the Tachometer is at 0 and when I'm driving 60-70 MPh it goes up to 900 or maybe 1200. It seems to be running fine no loss of power that I can tell. What could be causing the long crank time and my Tachometer problems.
the glow plugs and injectors are new I don't remember the brand and the fuel filters are brand new Motorcraft.
Ford 7.3L Power Stroke (1999-2003) :: Power Stroke Malfunction - In Reverse / With Lights On Engine Shut Off
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
Ford Super Duty (1999-2016) :: 2002 F350 - No Power / Speedometer And Tachometer Swinging Back And Forth
I have a 2002 F-350 with a 7.3 powerstroke. Last week, I replaced both my batteries. When I tried to start the truck, the electronics when a bit crazy. Speedometer and Tachometer swinging back and forth. Then when it did start it ran rough and after a minute it shut off. All electrical functions are completely dead. I finally unhooked the batteries and went in the house to cool off. When I came back, rehooked up the batteries, it started right up and everything acted normal. Everything was normal until last night, it started fine and was idling for about 5 minutes and it shut off. Absolutely, NO electrical power, even tried to jump start and still no electrical activity. Unhooked the batteries waited about 15 minutes, hooked them back up. It started just fine.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: E350 - Sudden Power Loss / Zero Power
I am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
Ford 7.3L Power Stroke (1999-2003) :: Will Cluster From 2003 6.0L Work In 2002 Model?
I have a 2002 7.3L Screw 4x4. Will a 03/04 6.0L instrument cluster work in this truck? The 2 clusters appear identical. I put the 6.0 cluster in and the trans temp, and coolant temp gauge will not work. All the gauges sweep when it is powered on, but the coolant and trans temp lay flat, and the check gauge light is on. All other gauges and functions work. When I put my other cluster in, all gauges work fine. Is there a difference in the VSM, PCM, or the SCP communication?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 F350 - Oil Leak When Parked After Running
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ford 7.3L Power Stroke (1999-2003) :: Power Port Not Reading A Full 12V?
Ok so the saga is continuing, not sure if its because enigma hates this mod or if I shorted something out when I was cutting the wires and mistakenly touched the ends together (protected terminal ends) some how or the monitor piece is just old and the fact that it has been my previous truck and this truck for a total combined 8+ years causing this conundrum....anyways the gauge seems to work (yay?) but it looks to read only "8"DC V?? but I know the power port (in dash) works as expected....so I am a bit lost here....one of the digits does look to be faded out as if the device perhaps is going bad and needs replacement....
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To PCM Fuse
I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
Ford 7.3L Power Stroke (1999-2003) :: No Power / Zero Voltage To Fuel Pump
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
Ford 7.3L Power Stroke (1999-2003) :: Low Power / No Throttle Response Under 1500 RPM
i got a 99 F250 powerstroke with 148K on its clock, i have a couple issues that i cant find a definitive answer for, 1 just started recently, Its an automatic and when it shifts into third around 40 mph the rpms drop to 1200-1300 or so, its done it since i got it, but recently it wont accelerate like it should or used to do, i have to put it down and make it downshift to recover.
Now I have no CEL. and it is still running perfect just has very little power, I do have a 4 inch turbo back exhaust and have a TS 6 position chip with i usually run in +50hp mode, but it does this in all positions. Now issue 2 is when its 30 degrees sometimes it will not start. It'll turn over with now fire. but if i cycle the key again it'll fire right up like a champ? It has a 4 month old starter and batteries and a month old alternator and i have tried several CPS' and Contently check the connections.
Ford 7.3L Power Stroke (1999-2003) :: Low On Power / Injectors HPOP Or Tune?
So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.
16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC
Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?
Ford 7.3L Power Stroke (1999-2003) :: Adapt 7 Connector Plug To Aux Power?
On the back of my truck I have two plugs to operate trailer lights/brakes etc but I only use one. The one I'm not using (pictured) I'd like to adapt for aux power in the trailer to operate some IP cameras. I need to know about the pin outs of this connector and what gauge wire to use between the trailer and truck. I plan on running the 12V and ground conductors from this plug through an adapter into the trailer.
In the trailer I'll have a 1000W inverter --> UPS --> TL-WR810N Router --> TL-SG1008P POE switch --> and 4 small ip cams.