Ford 7.3L Power Stroke (1999-2003) :: Fuse To The Starter Keeps Blowing
I had a problem with this issue a few months ago, was 45 minutes away from home, blew the fuse to the starter. Switched another one in, blew it too. Had it towed to a shop, they did some diagnostics, felt like it was a short in the starter, replaced it and all has been well (as far as that particular issue) until this morning. Got in it, turned the key it cranked for less than a second and stopped. I pull the fuse, sure enough, blown. Swap it with another, it blows.
I know I have a bare wire in the column, the OD light wire is chaffed, I fixed it before but it must be worn again because I can get it to light up depending on positioning of the shifter lever and as I recall, every time the fuse blows the steering wheel is cranked to the left.
Ford 7.3L Power Stroke (1999-2003) :: F350 Lost Power - Fuse Panel Under Steering Wheel Shorting Out
So I have a 1999.5 F350 diesel and the fuse panel under the steering wheel is acting up. I was driving my truck home the other night and I lost power and my truck shut off. I have had a problem in the past with the #30- 30 amp fuse ( controls the PCM and glow plugs from my understanding) that is under the steering wheel, I replaced the fuse and everything started working normally again. Until the other night when my truck shut off, so I replaced the fuse the truck drove again for 20 feet died again, I was able to hold the #30 fuse and allow my truck to start up again but would eventually killed the PCM and shut off again and would not start up due to what I believe the fuse location shorting it out and killing the power to the PCM preventing me from starting it up again.
I had my truck towed home and charged the battery and it started up fine the next morning. If I push on the #30 fuse my truck the shorts out and kills the power, I do not know if this is normal? The fuse is sitting loose in the fuse holder is there anyway making it fit tighter to prevent it from being so loose? I have read every other post online about the problems and tried everything they have recommended but still can not figure out what was wrong with my truck. I disconnected the fuel filter heater, and also the wastegate solenoid to see if that would prevent the truck from shorting out if I pushed the fuse it did not work.
What the problem could be causing the #30 - 30 amp fuse to be shorting out preventing everything from working? Or how to test the fuse panel and all the relays?
Ford 7.3L Power Stroke (1999-2003) :: Keeps Blowing 15A Starter Relay Coil Fuse
Upon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Dome Light On And Off - Noise Under Dash Fuse Panel?
I was to leave tomorrow for a trip with three horses. Last night when I parked my truck the dome light went on and off and there was a noise (like a relay opening and closing?) coming from the area. (I have been having issues with the turn signal getting "tired". At times they would only come on solid then other times try would quit after sitting at a long light.)
Checked my manual for fuses to this issue and I removed the fuse in the spot indicated for the "dome and courtesy lights", number 14. Actually I had removed spot number 15 (5amp). This ended the noise. Drove the truck after and all seemed in order, cruise control, turn signals, interior lights! This was the incorrect fuse according to the book! This event occurred with the ignition in the OFF position. Not wanting to start my trip before I get this in order.
Ford 6.0L Power Stroke Diesel :: 2003 F250 Not Starting - Starter Won't Engage
My 2003 Ford F250 superduty diesel wouldn't start. It was a cool morning and I suspected a problem with the glow plugs. I checked the GPCM ( new in the last year) and it was fine, than I tested both right and left harnesses...they showed two out of range. After further inspection I noticed both my buss bars were completely rotted off with the wire and top of the glow plugs exposed.
Since I cranked the truck over so much, I removed the ground terminals from the recently replaced batteries and put a charger on overnight, I also plugged in the block heater since the glow plug system is suspect. I went out the next morning, re attached the batteries, and turned the key. The fuel pump and injectors cycled as usual, than I turned the key to start....nothing....no click...no sound.
I disconnected the starter trigger wire and touched it to the positive post.... a few sparks but no click or engagement. I jumped the solenoid...again a few sparks...but no engagement. I removed the starter (less than a year old, and not a lot of use) and had it bench tested, it tested fine. I re installed the starter, and cleaned all the terminals and connectors through the the system, still nothing.
I checked the cable from the battery to the large terminal...12 volts, I had my wife try to start the truck and checked where the trigger disconnects on the fender and at the solenoid....12 volts when the key is turned to the start position. I used a jumper cable to run power from the battery to the solenoid...nothing, I ran the jumper cable from the ground terminal on the battery to the starter case...nothing. I checked all the fusible links and found a broken wire from chaffing, I repaired it ( but I think it was what was causing my battery light to come on for the last few months) even though the alternator, batteries and everything going else checked good.....nothing. I checked the starter relay...it checked out good, as well as the ignition fuse.
Ford F-150 - 1997-2003 :: No Restart / Clicking Noise Coming From Behind The Fuse Panel When Turn The Key
I have a 1999 f-150 and am having a problem that I cannot pin down . After starting the truck and running it for 10 min or so I shut it off and it will not restart again for approx. 3-4 hrs . When you turn the key there is a clicking noise coming from behind the fuse panel . Also the truck will not start if temp outside rises above 80 degrees . Is there a replaceable relay under there or is it the computer module ? Battery is new .
View 9 RepliesFord 6.0L Power Stroke Diesel :: Starter Will Not Engage And Its Cold Outside
I have a 2003 F350 6.0 liter crew cab. It's all stock minus the FICM and bullet proof I did a few years ago when I purchased the truck. truck runs amazing with 136K miles on her, but i rarely drive the truck and she's been sitting. SO, I went out to start her up because it's been in the low teens and I wanted to keep the battery up to par. When I had turned the ignition key on to start the truck (after I cycled the glow plugs), I could hear the starter spin but instead of turning the truck over, it made a grinding noise followed by a spin type sound which I assume is the drive gear of the starter not engaging. I can get her to start but it takes multiple attempts.
Once she's warmed up, it seems to stop grinding when i try and start it which makes me think it's more of a resistance issue, possibly a relay. BTW, where is the starter relay on our trucks? I am wondering if the cold has something to do with the proper power and amps to the starter via the relay causing the starter not getting enough power to the starter. Anyway, I'm hoping there is a way to diagnose this through my torque program by looking at amps but not sure which parameters to look at on torque android.....I'm hoping it's a relay problem instead of a starter problem. I really dont want to replace a starter with a bum shoulder.......in the cold to top it off
Ford 6.7L Power Stroke Diesel :: Starter Turned Over But Did Not Engage
With -37C and -50C with windchill today, I tried starting my truck after being plugged in all night, and it was a no-go. Sounded like the starter turned over but didnt engage. On another note, what is with the glow plug light? mine lights up for a few seconds, maybe, then nothing. Today was the first time it ever stayed on for 5 seconds, and that was only after i tried cranking it over twice. First two times it didnt stay on.
I think my block is still maybe too cold,maybe dead batteries too, and yes the block heater had power made sure to check that, I notice my passenger side battery has some corrosion ontop (1000watt amp hooked into drivers side) so maybe I am needing better batteries.
Usually fires right up, haven't noticed a problem lately either starting. Gonna let it warm up some more, and I put a charger on the truck too, gonna go check the battery voltages and see what it says. This is the coldest yet I have tried to start the truck.
Ford 6.0L Power Stroke Diesel :: 2007 - Fuse Panel Diagram?
I am looking for a fuse panel diagram for a 07 F350 6.0 ? The truck didn't have a owners manual in it and I have a couple things not working and testing each fuse is just more self hate than I can submit myself to today.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Trans Will Engage When RPMs Get Over 2K
Have to get rpm's over 2k before trans will engage, then in between shifts I either have to let off throttle or let engine rev over 2k to get trans to shift...
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To PCM Fuse
I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
Ford 7.3L Power Stroke (1999-2003) :: No Power To Fuel Pump / Fuse 30?
I have a 2003 F250 and dont have power at fuel pump, or fuse #30. I put power directly to fuel pump and it worked and truck fired right up.
View 13 RepliesFord Excursion :: 2000 - Clicking Noise Coming From Fuse Panel
Well I went to go to home depot and the key turned and my theft light started blinking and I hear a clicking noise coming from my fuse panel. By the way this is on a 2000 7.3l 4x4 limited. I found what was clicking (see picture) it is the second relay down, the one with the chipped plastic. My question is is this a relay I can replace or is it part of the fuse box? Where I can get a replacement? This is my daily driver so I need to fix this ASAP.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: DLC Fuse 3 Keeps Blowing
I have a 2001 F-450 SD with 7.3. What the problems would for the blowing of fuse #3. The DLC fuse. I mean I know it goes to the cigarette lighter as well. but when not in use it still blows.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Possible To Add More Circuit To Fuse Box?
OK I'm putting a plow on my truck. I am wondering if it's possible to add more circuits to the fuse box in some of those unused slots?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Gallon Of Oil Coming Down Around The Starter
I just reinstalled my turbo and started the truck up to test it. After 15 seconds or so it shut down so I hopped out to take a look. I had about a gallon of oil coming down around the starter. All I did was reinstall the turbo (I had previously installed without the rear pipe hooked up). I can't see where the leak is coming from but this thing is not even remotely drive-able. My best guess is the pedestal somewhere?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Low On Coolant / Oil Droplets On The Starter
Edit, I have also noticed I have been getting low on coolant, but without any noticeable coolant leaks. My engine oil still looks clean, where could the oil be going? How do I fix it?
2003 Excursion 153,000 miles - stock injectors, gt38r with new pedestal, Adrenaline HPOP, double transmission cooler.
I've noticed after some heavy towing with my camper (8,300 lbs), I've been getting a new oil leak showing up on my garage floor. I crawled underneath this afternoon and found three large oil droplets on the starter. See picture. What could this be dripping from?
Ford 7.3L Power Stroke (1999-2003) :: Driver Side Door Panel And Liner Off
I've taken the driver's door panel off, and unpeeled the liner. Now that the door is naked and exposed, I'd like to fix several things at once, rather than wearing the adhesive liner out by sticking and unsticking several cycles.
Here's a short list of some potential fixes I foresee taking care of while in there, how to :
1. The door ajar light. Mine went out over a decade ago, and the gallon of WD40 I sprayed into the latch did NOT fix it. In fact, it turned it from an intermittent issue into a permanent problem. I'd like to fix it now, as I miss having a light at night when the door is open. How do I fix it? Links, part numbers, tips, pictures, videos, search terms... all info welcome.
2. Bottom door rust. I don't really have much, but I see very faint hints of paint bubbling under the lower door weatherstrip barrier, which I have also removed. I've read about two schools of thought on preventative maintenance.
A. Pour oil or grease into the bottom of the door.
B. POR15 paint in the bottom of the door.
So basically, oil or paint? Obviously, one can't paint if one does oil, but on the other hand, some say that paint... especially thick paint like POR15, can actually do more harm than good by trapping moisture in the bottom pinch flange, or by creating craters or tunnels where water can burrow and then get trapped, rotting the metal away. What are your thoughts and experiences on this? I'd prefer a solution that minimizes the number of times I have to unstick the interior liner from the door.
3. I'm doubling the lower door weatherstrip with a combination of the older and newer designs. Ford sells the weatherstrip with clips attached, but neither those clips, nor the original clips, are really effective for what I'm trying to do. I've already done the rear doors, and made it work with the original clips, but they are brittle, and I lost a couple to breakage. Today, I broke three clips pulling the old weatherstrip off of the door.
I can't find these clips anywhere locally... I've tried every variety the auto parts and auto body stores sell, and Ford doesn't sell these clips separately from the weatherstrip... and even if Ford did, they OEM clips are not long enough to hold the double deployment of old and new styles of weatherstripping.
In searching this issue, it appears that a lot of people have broken these clips, which stands to reason with plastic in baking inside a hot door for 15 years. I'm sure I'm not the only one who would benefit from finding a good source of automotive clips.
4. Mirrors. I'm finally getting around to this, and this is what motivated the door panel removal in the first place. I need the dog bone harness that converts from a round connector to the flat style connector. Specifically, I need part numbers 1C3Z-14A411-AA and 1C3Z-14A411-BA. Ford didn't originally sell these dogbone harnesses separately, but included with the purchase of newer style outside rear view mirrors in case the translation harness was needed. Sometimes it was, sometimes it wasn't, so there would often be these unused harnesses left over.
5. Jimmy Jammers. Will they cause more harm than good? Does a better alternative exist? Thinking of installing these while I"m in there, but worried the door will be damaged worse as the thief tries to fight their way in. And, with body on shell doors, there appears to be much easier ways to break into an SD anyway, so part of me thinks, why bother
Ford 7.3L Power Stroke (1999-2003) :: Starter Sometimes Spins Free 2 - 3 Tries Before Engaging
I just bought a 99 F350 to replace my 01 F250 5.4 and I'm pretty stoked. There are several problem (some i knew about, some were surprises) 1 of which is the starter. The guy I bought it off said that every 100 starts or so (more like every 4-5) the starter sounds like it free-wheels but you just wait for it to stop, turn the key again (sometimes twice) and it engages and starts (although it takes a few seconds of turning over before it fires up).
I have a buddy with the same truck and he has had to replace his starter many times and I read in an old log book from the original owner that he had replaced the starter every 25,000kms (15,000miles). I am not the kind of guy who likes to fix things to have them break again.
SO my question is, WHY do the starters on these trucks keep breaking? What is the weak link? Is it possible to re-build one with better parts at home?
Is the problem partially because my batteries are only 650CCA and 750CCA and it takes more to turn this beast over? Could it be a bendix issue?