Ford 7.3L Power Stroke (1999-2003) :: Thermostat Housing Broken Bolt - Replace Water Pump?
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Overheating - Water Pump Impeller Slipping?
have a 2006 f250 with the 6.0 Powerstroke diesel started overheating yesterday the ECT and EOTcheck fine with the scangauge always ran with in 8 degree's of each other. Thought maybe water pump impeller may have been slipping so it is new with no change. Fan kicks on like it should. Heater works good so don't think it is a thermostat.
View 13 RepliesFord 6.0L Power Stroke Diesel :: A/C Leak Found - Rubbing Metal To Metal Caused The Pinhole
Getting the RV ready to go for the summer, and no a/c. I started to add freon, and found the leak right away.
It's on the 3/4" pipe that goes right over the upper radiator hose; obviously rubbing metal to metal caused the pinhole. Now I know where that mystery green snot came from all over my radiator hose coming back from Yellowstone last fall.
First thought was to replace the entire pipe. There's an easy threaded connector on the upper end, but way down on the compressor is a strange fitting that looks like a triangle stuck against a cube. I can't see how I'd get a wrench in there very easy anyway. What is that fitting?
I bought a Dorman 3/4" repair kit, but until it arrives in the mail I don't know if I've got enough straight pipe to work with. Do I need to add oil as well as freon once I charge the system again?
Ford 6.7L Power Stroke Diesel :: Truck Makes A Metal On Metal Screech When Downshifting From 5th To 4th And 4th To 3rd Occasionally
I've had transmission issues with my truck that the dealers can't seem to duplicate. The truck makes a metal on metal screech when downshifting from 5th to 4th and 4th to 3rd on occasion. The two dealers claim they cannot duplicate the issue and there's no CEL so there's nothing they can do. The shifting is also super slow between gears and regularly hangs in 4th until I let off the pedal for a good two or three seconds. All gear changes are slow.
Now the truck is exhibiting a new issue. When coming to a stop, a second after stopping the truck faintly jerks forward. Almost like the torque converter is not fully unlocked.
Ford 7.3L Power Stroke (1999-2003) :: A/C Leak Coming From Metal Tube Going Into Spongy Area
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
Ford 7.3L Power Stroke (1999-2003) :: 0 Oil Pressure At Idle And Metal Shavings On Drain Plug
Here is what's going on. A few days ago I noticed my oil pressure gauge drop and come back up as I was shifting from reverse to drive. Then a few days later on my way home from work I noticed that when the truck was warmed up and I was stopped at idle the oil pressure gauge would drop to zero and the oil pressure light would come on.. Once I gave it throttle the pressure gauge would go back to normal. After researching for the night the next morning I started the truck cold (around 35 degrees) and watched the oil pressure gauge. It was fine until the temperature came up then once I hit the brake to stop the high idle the gauge dropped to 0 and the oil pressure light came on. If I gave it any throttle the oil pressure would come up to normal but soon as I let off the pressure would drop off again.
I drained the oil, removed the oil cooler, and checked the oil pressure regulator to find it in normal operating condition. My new orings and gaskets won't be here until Monday so I cleaned up for the day. When picking up the oil drain plug I noticed quite a bit of metal shavings on it. I cut open the oil filter and found more shavings in it. Not a bunch but a few in every opening. I have read about a lot of issues where piston cooling jets fall off and cause my issues. I tried hitting the oil pan with a dead blow hammer and listening for the jet but don't hear it. This is the first time I have changed the oil since buying the truck and am wondering if it was found the last time the oil was changed and the reason for them selling the truck. I'm going to put a bore scope through the oil drain plug today and look for the piston cooling jets or anything not normal. Then when the oil cooler gaskets get here I plan to install them and a mechanical oil pressure gauge. To see what the pressure really is.
Ford 7.3L Power Stroke (1999-2003) :: Driver Side Rear Brake Metal Line Cracked
I had a brake line crack on my way home yesterday(that was interesting..) It was the drivers side rear metal line from the splitter to the rubber hose. I went to autozone and was like ok easy enough this line is the same length and appeared to be the same diameter. bend to fit and all was well or not.. the fitting on the end was a different thread pitch and size. 1999 f250 4wd if it matters....
View 4 RepliesFord F-150 - 1997-2003 :: Metal On Metal Noise Coming From Rear After About 25 To 35 Mph
My father's 1997 F150 with the 4.6 two wheel drive, has me stumped again. I have a lot of mechanic knowledge but this one has got me wondering whats going on. Here is the run down. When you are driving down the road, it rides just fine and makes no noises from 0-20 MPH, after about 25 to 35 mph it makes like a metal on metal noise that is coming from the rear, and forces the truck to slow down, when you try to accelerate through this problem it has a bad bang and it wont allow you to speed up anymore, it does not seem like a brake issue (but I could be wrong) since it does not actually pull to one side or the other.
It seems like an equal force trying to stop the truck. I have heard rear ends that were going out and they make clunk noises or whirring noises etc, but its still some what driveable. I have checked the rear end oil and it does have oil in it, and its probably about an inch from the full level (but that shouldnt cause this issue im sure). My father wants a definite answer before we start tearing this thing apart to try and fix it. Since its mostly used to take trash off, and also get the kids down the dirt road to the bus stop.
Ford 7.3L Power Stroke (1999-2003) :: Light Metal Rubbing Noise Coming From Front Left Wheel
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
Ford Super Duty (1999-2016) :: Metal On Metal Ticking Sound
I thought i heard this yesterday when i left work but i was tired and said its in my head, THEN i go to leave right now and sure enough its a real sound, you can hear it very well through the front grill and then if you turn the volume up you can hear a ticking sound ever half a second or so, it also speeds up when i was pulling on the throttle cable. And after the truck fully warms up it goes away.......
View 14 RepliesFord Super Duty (1999-2016) :: Metal On Metal Noise From Front End
What we have is a 2011 F-350 with the ambulance package (obviously) and it has started making a very annoying sound from the front end. It has been into two different Ford Dealerships and they have not been able to remedy this issue. What happens is, when we are backing and turning, the front end makes a bad metal on metal grinding noise. When going straight down the road no issue just turning while backing. I know this is an ambulance and has the ambulance package but I think from the cab forward should just be all ford right?
View 2 RepliesFord Super Duty (1999-2016) :: Rumbling At Idle / Sounds Like Metal On Metal Vibration
Just last night, out of the blue, I've got an odd rumble at idle. The noise goes away under load and any time the rpm's are up over ~1300. It sounds like metal on metal vibration, but I don't see any loose exhaust parts.
I've looked at threads saying possibly a broken flex plate. Other than the noise, would there be any other symptoms? I don't notice any loss of power. I suppose I could pull the inspection cover and take a look, but I don't have any experience with auto tranny's and don't really know what I'm looking for.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Leak / Dripping At Side Of Starter And Collecting At Low Point Of Metal Lines Down Below
I've got a late 99 7.3 truck that I just recently did a lot of work on. I installed a new turbo with bellowed up pipes and a new exhaust system and when I went to start it up it started leaking fuel in the back pretty badly. Initially I thought it was the banjo bolt or the passenger fuel line but looking at it more closely I realized that it's not coming from there. It's dripping all over the side of the starter and is collecting at the low point of the metal lines down below. I also saw small droplets coming out of the up pipe where it meets the manifold but it looked like nowhere near enough to produce the kind of leak I'm seeing, also I know fuel shouldn't be coming out of the up pipe to begin with. This is really annoying and I would like to drive my truck again.
View 14 RepliesFord Super Duty (1999-2016) :: Loose / Binding And Metal On Metal Sound On Steering Wheel Shaft
I have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Grinding And Metal Chewing Sound Coming From Front Axle Or Close The Wheel Hubs
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
Ford Super Duty (1999-2016) :: Coolant Leak Coming From Metal Housing Behind Alternator
I trying to see if this is something that is a easy fix or mayor work. Leak coming from that metal housing behind alternator. Does this housing came off? or do I need to take out the intake out? .
View 8 RepliesToyota - Solara :: 2003 - Metal On Metal Sound Near Driver Side Of Engine
I have a 2003 Toyota Solara 4 cyl. auto. transmission. I recently had the head replaced. Now it is making a metal on metal sound near the drivers side of the engine. It makes the sound during idle, when I change gears, and the sound increases when I rev the engine. What could it be?
View 8 RepliesCamry :: 2003 / 2.4 - Metal On Metal Sound When Driving Through A Tunnel
I have got this noise which sounds like a light skimming of metal on metal. It sounds like a roller (airport baggage) spinning. It can be heard mostly when driving next to a wall or past parked cars. I suspect it being the bearing in either the water pump, idler pulley or even alternator. The car has 330000 kms but it is serviced regularly in which all fluids have been changed over time. I just want to drive through a tunnel and not hear any non harmonic sounds coming from the front.
View 10 RepliesToyota - Rav4 :: 1997 - After Replacement Of Timing Belt And Water Pump Noise Like Metal?
I had the timing belt, water pump and thermostat replaced on my '97 RAV4. The next morning while braking at a red light I heard a rapidly repeating sound that sounded like metal on metal. The car never made that sound again but now I'm hearing a noise coming from the passenger side of the engine (timing belt side). When the engine is cold I don't hear it. After driving a while its starts, then once the engine warms up it generally goes away (except for this morning which was the coldest morning since this started, temps in the 40s).
I was only hearing the noise when the car was stopped either in drive or reverse (reverse sounded louder) if I lightly let up on the brake pedal (there's no pulsing in the brake pedal). Once under way the sound goes away. This morning it was making the sound virtually every time I came to a stop (once the car warmed up) even with my foot firmly on the brake pedal. I recorded the sound Saturday while standing still with the car in drive and my foot slightly easing up on the brake pedal. The sound starts at the 20:30 mark, what it could be?