Ford 7.3L Power Stroke (1999-2003) :: High Pressure Power Steering Hose
My high pressure power steering hose just blew at the "B" nut at the pump. Meaning, the fitting is still in the pump but the line is out. Do I need to replace the whole line or is there a retainer I can swap out?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: High Pressure Power Steering Line Blown?
I just replaced my 3rd HP power steering line last night( 3rd in 300K, always blows the same point....fitting comes apart where it attaches to the pump.
I'll start, mine have gone about 100K plus or minus 10K, almost thinking about making it a 100K maintenance item.
Ford 7.3L Power Stroke (1999-2003) :: For AC Optimum Low / High Pressure Readings?
What are the most favorable low-side/high-side pressure readings for the AC when fully charged?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Injector Cup Causing High Pressure Oil Leak
I just replaced my injector cups a month or so ago and also injectors with some lower mile injectors. but now 3 weeks later still not getting any pressure at icp. I have dead headed pump got 3k plus but when i block off ether head i get no pressure. i have pulled injectors and checked for orings and they are fine...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Testing High Pressure Oil System / Air Coming Out Of CCV
'99 7.3, 258k miles, looses oil fast, oil found in coolant (though not a lot) and the fuel bowl is full of oil.
I re-ringed the oil cooler. Most of the coolant and oil is drained. The HPOP holds its oil level and does not leak down.
Someone shared the below test. Though it says #4 ORB, the actual thread on my IPR is #8. I removed the IPR and threaded in the #8ORB to air hose adapter. I regulated the pressure to 20 psi. The air is rushing out of the CCV.
I suspect I am missing something in the below test and that I'm pushing air back through the low pressure oil pump and into the crank case.
The test shared with me elsewhere:
Apparently someone named "Cody" on the forum did a test and it was labeled that way.
AIR TESTING THE HPO SYSTEM:
7.3L Powerstroke engines may experience hard start and or no start issues. In some cases the no-start issue may occur only with the engine hot. If the observed ICP pressure during cranking is less than the required 500 PSI, then the problem is in the high pressure oil system.
One of the first checks that should be made is to remove the plug from the top of the high pressure oil reservoir (in front of the fuel filter) to observe if the reservoir is full. If the oil is standing within an inch of the top of the reservoir, then the problem is in the high pressure oil system and could be caused by one of three things:
- The high pressure oil pump itself
- The IPR Valve
- A high pressure oil leak
Tools: Adaptor ORB #4, Air Compressor capable of maintaining 90-100 psig, Air Line Adaptors which will allow connection to the #4 OBR , IPR Test Harness, Grease Gun Whip or any whip with a .0625" NPT.
Remove the IPR valve and insert the ORB #4 Adaptor. Attach Shop Air and pressurize the system. Wait for approximately 30 - 60 Seconds while the air travels throughout the HPO System. Listen for air escaping through the Oil Fill Tube (cap removed).
External high pressure oil leaks would have, of course, been obvious. The primary concern is internal leaks under the valve cover(s). These could include leaking injector O-rings, or leaking injectors. Listen for any air escaping under the valve covers and correct if present.
If the center injector O-ring has failed, high pressure oil may be forced into the fuel system. Remove the fuel filter cap and observe for air bubbles in the fuel. If necessary, individual fuel lines running from the fuel filter assembly to the cylinder heads can be disconnected in order to isolate the problem to which side it is occurring.
2. 7.3L: If no air leaks are observed, the next step is to isolate whether the problem is with the IPR or the high pressure oil pump. Remove the IDM fuse or unplug the IDM or injector connectors at the valve covers to prevent starting.
3. If this test does not assist in diagnosing the issue, remove both valve covers and witness oil from the deflectors as being uniform, look closely at the injector base for any sign of air or oil escaping during test. This is an indication of a loose injector or O-Ring failure.
The same can be done at the ICP Ports (Oil Rail) on either side to determine leaking O-Rings in that Bank.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Rail And High Pressure Oil Cross Over
Next mods are for the fuel rail cross over and the high pressure oil cross over. I see the unused ports will come in handy.
Fuel delivery? any specialty mods to run the fuel lines? I see it's a #4 ORB fitting. Anyone ever use a "T" or a splitter off the fuel bowl to have a quad line set up?
Saw the FRx from RiffRaff .... not sure how it eliminates air from the system 7.3L Diesel Fuel Rail Crossover? (FRx) 99-03 Powerstroke
Ford 7.3L Power Stroke (1999-2003) :: Engine Oil Temps Too High
What kind of engine oil temps are too high? I know pulling the other day it got as high as 220 but I honestly only have the gauge cause I got it for free. Whats happening at the different temps? I know for trans fluid but not for engine oil..
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Weak HPOP / High Pressure Oil Leak?
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Reconnect High Pressure Oil Line To Rail?
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Rough And Lacks Power When Cold But Smooth At Warm?
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Shut It Off Warm And It Won't Fire Again
E99 zf6 180k. Ts 6 position and 6637. Just found d out the oil was 25000 miles old and changed it. 400 mile trip followed by a few days in town with no problems. Shut it off warm and it won't refire. Takes 3 loooong cranks. Few minutes later it restarts hard but not as hard. Head out for a few hundred mile trip and it's running fine except all of a sudden "bucks" a few times within a couple hour window. I took data during the trip and never saw anything strange. Today a cold start, around town driving, and warm restart were all normal.
My thoughts are to
1. Verify steady fuel pressure (I only have a temporary gauge setup)
2. Check the fuel filter for oil.
3. Pull the valve covers to look for injector oil leaks.
#3, though, I dunno if it's worth it. Perdels look fine and icp seems to be about the same as it always has.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Misfire After Warm Up At Low RPM?
I started my truck this morning and drove it quarter of a mile down the road to get some food letting it idle while in the drive through. While pulling away from the drive through window it started idling ruff . I drove it to the hotel and it ran perfectly normal until at a stop light and it started skipping again. If I put it on high idle it really starts skipping. Above 1500rpm it stops. What do you think?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 Will Not Restart Again After Engine Gets Warm / Bad HPOP?
2003 with hot no start issues. It starts fine in the morning however will not start again after the engine gets warm, after an hour or so of cooling off it will eventually go. Not sure if I should start with.... Readings below ....
FICM L 13.5v
FICM M 48v koeo and 47 running
IPR 14.7% koeo
IPR 74.6% cranking (no start while hot)
IPR 40% (after cold start while running
ICP 737psi cold start
ICP 1600psi engine running 2k rpm
ICP 360 hot while cranking
Ford 7.3L Power Stroke (1999-2003) :: Truck Just Dies Like Shut The Key Off When Warm
I have a 99 7.3, I took off driving the other day and after about 10 minutes the truck just dies like I shut the key off but everything was still on. I tried to restart it and it would fire for just a sec then die. I set for about 15 minutes and tried again it fired up and ran about 5 mins then the same thing. I had a buddy hook it up to his scanner and it has a p0605 and another icp code.. We changed the icp then erased the codes.. Ran some rest through the scan took with the truck running and no codes so we took it for a drive made it about 20 minutes away and same thing but this time has the p0605 code again. Could the pcm be bad? I also noticed the electric pump is always on all the time it will cycle at least 30 seconds every time the key is turned??
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Surging During Warm Up And Some Low RPM Hesitation - No Start
My truck - early 2000 CC short bed, 300K miles
Background on my problem: I had a short list of long overdue maintenance and updates to do that time and money kept me from tackling. Found a little of both so I replaced the water pump, HPOP lines, re O-ringed the HPOP/IPR, deleted the AIH, replaced all of the brake lines in the engine bay, put new fuel lines to the filter bowl. All of this took me about 2 weeks so the truck sat with the batteries out for that long.
After buttoning it all up, it fired right up, a little slower than normal but figured that was air in the fuel lines, HPOP, etc. The only issue I had was the battery light stayed on. Thinking I had an alternator issue, I checked it and it was getting about 14.25v so figured that was good. I used it regularly for about 3 weeks, the light stayed on, and noticed some surging during warm up and some low rpm hesitation.
Then it stop dead on me driving down the road. Turns out it was all my doing, I had torqued the bolts on the water pump pulley but didn't use Locktite. The bolts backed out, shredded the belt, and ended up yanking the CPS wire harness out of the sensor. So that made total sense.
Fast forward another week, got new wiring pigtail and CPS (never replaced it before now) from a couple of the good FTE vendors. I am not sure about the wiring on the pigtail, my truck has a green, blue and brown/gray wires, the wiring diagram I found online showed green, blue and gray. I wired it connecting the brown/gray where the gray line goes (center contact) and closed everything up.
Another thing to mention is that I have an Edge Juice with Attitude that has been on the truck since '06. I lost that connector in the process and they were absolutely no support in trying to get me running again. Wouldn't or couldn't tell me which wire they connect to so I used the green wire which is the CPS signal wire to the ECM. Once I am running again, going to get rid of the Edge.
So that is where I am now. No start, I've been reading some of the "what to do" posts, the most likely is that I don't see the tach bounce when trying to start. So I want to check the wiring to make sure I have good connections to the CPS.
So I don't have any diagnostic software to read codes, etc. I really need to fix this myself and only have one set of hands most of the time. Not really sure what the problem was before it stopped running and now I can't diagnose the surging and hesitating.
Ford 7.3L Power Stroke (1999-2003) :: White Smoke At Idle When Warm
I have a Tymar intake, magnaflow exhaust, a DP Tuner and I have Rosewood Diesel injectors.
I had a bad oil leak recently and it seemed to be coming from the turbo area so I changed all the o rings back there and deleted the EBPV system (I cut out the butterfly and welded the holes shut, cut the part of the pedestal that held the actuator because it looked like it was leaking and welded the oil holes in the pedestal that fed it. I left the actual EBPV sender in the pedestal and kept it connected to the harness)
After all that was done I checked the oil and it was low but still on the dipstick so I drove it to the local parts place to get some more oil, about 2 miles, because I wanted to check for leaks. It was not happy, ICP low code came up it was sputtering and jerking when stopped at a light. I got to the store and parked it, it took about 3 litres of oil and seemed to run pretty good after that.
But on the way home I noticed a bunch of white smoke, I figured maybe an injector was stuck. I started it a little later and no white smoke in the driveway so I thought maybe it had gotten lubed enough and had sorted itself out. That was a few days ago.
Today I started it and let it idle in the driveway for about 15 mins and no white smoke, I wanted to get it up to speed a little so I took it to do an errand that was about 10 miles away, lots of lights and a bit of highway. It would run fine while going at speed but as I would slow down for a light the ICP would go down to around 600psi and the white smoke would start, as sitting idling a huge cloud of white smoke would form (yes, I was that guy), once I could take off and get it running a bit harder it would go away again.
I am assuming that I have a stuck injector (or cracked), I have no oil in my degas bottle and it doesn't look like it is fuller than before. Seems like I may have used more fuel than I should have, but pretty hard to tell just from the fuel gauge.
I have tried a buzz test and they all sound the same, tried a Compression Contribution test, no codes from that.
How can I locate a stuck injector? If that's what it is?
Ford 7.3L Power Stroke (1999-2003) :: Starts But After 5 Seconds Of Cranking Even Warm
I am a longtime 7.3 IDI guy with an 88 F350 crew so i know about diesels. But this is my first electronic diesel. I picked up a 2001 F450 2wd auto 260k miles. it used to be my work's truck but was stitting for a year and now i got it in "non running condition"
I towed it home and got it started by replacing the batteries and using the block heater.
As expected it took a few tries of long cranking to run the first time. runs pretty good and no smoke. what surprised me is it still takes about 5 sec of cranking to restart each time when warm too. any direction you would look with those symptoms? HPOP, IPR?
i am pretty sure the glow plugs all work because mechanics had replaced all that stuff. but i know back when the truck was last used it would still never start cold unless plugged in (even in summer).
Ford 7.3L Power Stroke (1999-2003) :: Truck Hiccups Under Idle And Dies When Warm
I've been working on my truck for months now on and off. I thought i finally had it back, but i have (again) problems with running. it basically only ran for a full day (hauling trip) after getting it back up and running. next day, it died on me on the road.
The new deal right now is that I can make the truck start and it will run, but it has little "hiccups" or misfires that will happen every now and then. Once it gets warm enough, the idling sounds chopped (best way i can explain it). After "chopping" it will then run fine (until the next chop). then it seems that once the truck gets warm it just stalls out. When that happens (shutting off) i can't get it to start right away. i have to wait awhile before it'll start and that lasts only so long.
The truck puffs a tiny bit of white smoke. not constant but more like a "puh - puh - puh" ....I've changed out quite a bit of used up parts now...
Turbo
Injectors & wiring harness
valve seals
IDM
ICP
IPR
CPS
MAP
fuel pump
vacuum pump
glow plug relay
starter relay
All the sensors are OEM. There's fuel in the fuel bowl, and the filter is clean. Plenty of oil in HPOP & oil level in crankcase is good. Have plenty of fuel.
Air filter is clean and fine. No codes. No lights.
2001 f350 7.3 320k on it.
Ford 7.3L Power Stroke (1999-2003) :: Little White Smoke After Good Warm Up - No Start
So I was on my way to work on a semi-chilly morning here in Colorado. Every day as usual, a little upset in the morning, a little white smoke and after a good warm up i'm on my way. About 10 minutes up the road while accelerating on the freeway, I hit I guess the perfect RPM range (2000-2500) when all of a sudden my CEL came on. Right as the CEL showed up, the engine introduce to me a new skip and lost a bit of power. About 5 more minutes up the road, the CEL went off and the skip went away, unless in idle. I made it to work a few minutes later and the skip in idle was apparent for sure. I turned her off and just couldn't get her to turn back on. The injectors are just not firing, no smoke at all, they don't even sound like they're trying to fire almost like no signal to the whole engine.
I replaced the CPS, the IPR and unplugged the ICP to test if she'd go. I opened the fuel bowl and watched it fill up. I checked the HPOP level, it was almost full, maybe a quarter (between half) inch from the top. No codes.
She ran great until this, outside of needing glow plugs. When I was trying to get her started it was 60ish outside so I don't think glow plugs is the issue. It sounds like the Injectors are not firing at all, whatsoever.
I will note that I had a few fuses blow out of no where that I replaced, a trail light, OBD fuse and one other in the under-dash box. I had her dyno'd a few weeks back and the tech said she made great power but sounded like she had a little issue recovering from the high RPMs but I figured my injectors are tired.