Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Hard / No Start At Cold - Injector Buzz

This is an issue I started chasing after having all the injectors replaced on my aunt's F-350. We had them replaced due to hard/no start on cold (dealership told her they needed to be changed). Unfortunately, I did not get the buzz test results before changing the injectors.

So far that has been replaced:
Injectors
ICP (was leaking)
IPR
both UVCH
IDM (twice)

The issue we are having right now is that only 2 injectors (#6, #7) buzz properly. Initially when we changed the injectors, it did start but didn't seem to run quite right. We did the buzz test and at that time and injectors 1,3,5,6,7 would buzz strong but the rest were weak. After some forum lurking, we suspected that the IDM was faulty. We purchased a refurbished one and after we changed it, only injectors 6,7 would buzz strong. Thinking a faulty IDM was sent it back for a replacement. While waiting, we decided to put the old one back in figuring it would go back as it was before but only 6,7 would buzz strong. We receive the second IDM and same thing, only 6,7 buzz strong. We did a continuity test from the IDM connector and they all get 2.7 ohms (it was an older multimeter so not sure if being .1 under the 2.8-3.6 range is bad).

What I did next is use the uvch external pigtail to test the injectors. I plugged the extra pig tail into the uvch and then the ends of the wires into the plug of the upper harness. Afterwards, I would swap a different injector wire (on the pigtail) to the #6 injector wire (on the upper harness). Whatever injector that would go to #6 would fire correctly. So I know that the injectors themselves are fine. I am suspecting the wiring harnesses (upper/lower) but the continuity test would say otherwise. We also do not get any fault codes except for the EBP occasionally (waiting for a new one). I am lost on what to test or look at next.

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: Bad Injector O Rings Cause Blow By And Oil Consumption?

I have a 2002 F350 7.3L w/superchips programmer, k+n cold air intake. Does NOT smoke a lot from tailpipe

Not running rough since I changed my oil to rotella 5w-40w synthetic.

Appears to have good amount of blow by coming from the oil fill when engine is warm.

Can Bad Injector O Ring(s) cause blow by and oil consumption?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Hard To Start On Cold - Oil Leaking?

20 degrees out this morning truck not plugged in, didn't want to start had to cycle 4-5 times, each time waiting for glow plug Light to go out.

Finally cranked didn't sound pretty but cranked. Once it started idling on its own got out and seen a puddle of oil under the front of the engine drivers side center kind of.

Got up on the truck and shined a light in the valley and seen a puddle in intake valley. Heres my question? Where did this oil come from? Once it warmed up it quit and oil kinda disappeared from valley???

I had turbo off a few months ago because I thought I had a bearing down in it, but found some bolts lose. When I put turbo back on I broke the wire plug on front of the pedestal so I just left it unplugged. Very hard to cold start now that that is unhooked.

Did leaving this unhooked create a hard cold start? Should I put another pedestal on it with the plug or install one without it? Also will it hurt to leave plugged in overnight?

View 13 Replies

Ford 7.3L Power Stroke (1999-2003) :: Still White Grey Smoke After Replacement Of Rings On Injector?

I replaced the rings on all 8 injectors put in 8 new glow plugs and a relay. My truck is still putting out grey/ white smoke at start up. It goes away after about a minutes. Truck runs a little rough a first then smooths out. I know some smoke after doing a job like this is to be expected but I was thinking I t would go away by now. I've been running through my head what I might of done wrong but I can't think of anything.

Does it just need all new injectors and not just rings ?

2001 f250 7.3

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard To Start Cold - No Codes

My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?

View 10 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard Start When Cold / White Smoke

When it is cold out side like 20 degrees I'm having problems starting my 2000 7.3 I'm cycling it about 5 times and misses smokes white for a bit then stays running I was thinking of changing out the fuel filter. What it could be?

View 6 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard Cold Start / Now EBPV Not Working

It's been a while but thats because the truck has been performing well.

Current problem: The truck has been hard to start this year as if the glow plugs are not working or are bad. It will start right up if I use the block heater.

Just recently, I also noticed that the EBPV is not coming on when warming up the truck.

Also, This winter season, the engine temp is not coming up to normal. the engine temp needle is more on the low side towards the C and definitely less than 1/2 way up where is normally is. When driving on the highway, the temp comes up more. but sitting at idle it barely gets warm.

So not sure if all 3 are related or not, but looking for a starting point.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: F350 - Hard Start When Engine Cold

2003 F350 7.3L 164k miles. Got towed in with hard to start cold complaint.

Hooked it up to the Snap On Verus Pro scan tool and we get up to 3000 psi on the ICP cranking, IPR value seems within spec, we have rpms over 100 on tool, pulse width within spec, computer voltage above 10v while cranking, verified output of glow plug module (California) and glow plugs get voltage for approx 50 seconds @ 80 degrees farenheit, glow plugs all read 0 ohms resistance.

injectors do NOT sound the same during buzz test.

Vehicle takes EXCESSIVE cranking cold to eventually get it started. LOTS of cranking. Just had to replace starter and a battery because driver burned em out. It feels like the vehicle shakes when it gets running. Black smoke when revving cold. Sometimes white smoke while cranking.

Once the engine has been warmed up, it starts perfectly every time.

I have spent two days in the engine bay looking for chaffed wires and doing diag and my current diagnosis is bad injectors. I feel there COULD also be high pressure oil leak, or a mechanical issue such as low compression. No compression guage yet for this truck. We have the ICP and IPR fittings to do a shop air test. Recently did a 6.0L and went thru everything and eventually diagnosed it as bad HPOP. LOW ICP pressure.

I noticed two of the cylinders were at maybe 8% Perdel on the data. Seems too high. Also, it "passed" the KOER self test and "passed" the injector buzz test with no codes after, but the audible sound of injectors didn't "seem" right to me, but I am new to these engines.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard To Start When Cold Outside But Eventually Fires Right Up

My 1999 F550 7.3L has been hard to start when it's cold outside since I got it with about 150k on it (it has 200k on it now). Last year we tested the glow plugs and sure enough 5 of 8 were bad. So they are all new now. It worked a little with the hard start, but not much.

When it's cold out the engine will crank forever amongst clouds of smoke and the smell of unburnt diesel fuel and sometimes eventually start, followed by smoke and sputtering until the cylinders clear out. However, what I have noticed recently is that it will sometimes start in the first few revolutions. It seems like the best way to start cold is as follows:

1. Let the glow plugs heat up for a minute or two,
2. Crank engine for 10 or 15 seconds and stop,
3. Crank engine again, but stop if it doesn't catch in the first couple of revolutions,
4. Repeat step 3 until engine starts.

When it starts using this method, it's immediate and it's running smoothly immediately with minimal smoke. This is making me think there's a computer or sensor issue, but I have no codes.

View 13 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Hard Start On Cold - Temperature Sensor / PCM?

I have a 2002 f350 that has had cold starting issues since I bought it. I have replaced the glow plugs twice, the glow plug solenoid four times. When I put a new solenoid on it it works fine for a short time. I know the solenoids are bad because I get battery voltage on one side and nothing on the other. If I jump the solenoid with a jumper wire I can get the truck to start. I thought I was getting bad solenoids but I have recently tested the activation circuit and am getting constant power there. I.e. It never shuts off. I think this is what is causing the solenoids to burn up. From the tracing of wiring diagrams I have done, the only thing before the solenoid is the Pcm. So now to the question,

1) What controls the activation of the Glow plugs? Is there a temperature sensor or something before the Pcm.
2) Is this a case of my Pcm going out on me? I am a mechanic in the army so I have a decent understanding of mechanics.

However I am at a loss for these systems.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard To Start / Smokes And Running Rough When Cold

I have a 01 7.3 crew cab dually and it's had cold start problems since i got it in 09.I have replaced everything i could think of including glow plugs gpr,harness and batteries. Any temp below 40 i have to plug it in . If i cycle it 3 or 4 times it will start but it smokes and runs ruff. My 00 7.3 excursion starts up down to about 10 degrees than i have to plug it in so i know dually is not right.

I have a afe intake,1.5 injectors, driven diesel rr, adrenilin pump,dp tune by gear head. Kinda at wits end don't mind plugging it in in dead of winter but now one night it's 30 next it's50 and i don't have to . Also have fully built trans by level 10 if it matters .I get battery light coming on every now and again. New alt about every year and a half.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Hard Start In Cold But Starts Fine Rest Of Day

2002 Excursion, 7.3L 375,xxx miles ... As the weather is cooling off, my excursion has a starting problem for a few years.

Replaced all the glow plugs last year. We (my brothers and I) thought it was injectors, but in the summer time or if block heater is plugged in, she starts normally and idles smoothly. And no smoke and runs fine once she warms up.

When cold, it acts like 1 or 2 injectors are not firing. Have run all kinds of cleaners through the oil and fuel.....

Don't want to swap injectors just to swap parts. Would like to diagnose problem....

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Injector Hold Down Bolts Not Torque Down To Spec - Hard Starting?

I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: Replacing Pedestal O-Rings?

My 1999 F-350 7.3 is leaking from the turbo pedestool o-rings, from what my mechanic tells me. I would like to do this myself as it does not seem overly hard. This is my first diesel truck and am not quit sure how to do it. Looking for instructions or pointers on the process? I am a decent mechanic, but just have no clue on diesel engines and hoping to learn.

View 7 Replies

Ford 6.0L Power Stroke Diesel :: Bad Rings On One Piston / Signs Of Leaking

How my rings burnt up on one cylinder causing damage to my cylinder wall. My question is this. What could have caused this? I pulled the motor and tore it down. Cylinder wall is chewed up a bit so I was going to have the machine shop sleeve it. Is there another component that I should look at while it's apart? Also the corresponding freeze plug on the same cylinder was showing signs of leaking. I'm thinking that is related to the extreme heat that cylinder experienced.

View 12 Replies

Ford 6.0L Power Stroke Diesel :: 2003 - Hard Cold Start?

2003 Excursiom 4x4 Limited

My first Diesel. Runs and drives great. Torque Pro app only showed coolant temp at 188. Would not show oil temp. Hard to cold start. New injectors. Has a programmer. He is asking 12K. It has 209K miles.

It belongs to a friend of mine and he rarely drives it. It stays under a cover most of the time.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2003 - Hard To Start And Runs Rough When Cold

My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.

From what I've read the common culprits are:

1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors

I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.

I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.

I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Fuel Leak - Not Water Separator Valve O-Rings

I have a very small fuel leak in my 2001 F-250. I was going to just let it go until I needed to do other work (since I get 20mpg city and 25mpg highway), but I went to a "new" inspection guy, and he flunked me. So now I have to fix it. And for all I know, my mpg and fifteen other things will break when I try to fix this.

Today I spent 4 hours in the heat putting in two new o-rings on the water separator valve. But the truck still leaks fuel. Climbed up on top of motor while it was running and looked, but I don't see where the fuel is leaking out.

Online research suggests to me that the next most-likely culprit is a steel fuel line that wears through from vibration and chafing. Is that correct?

This truck is so eaten up with rust (came from salt belt) that I bought a LOT of fuel line stuff a year or so ago, so that when things started falling apart from rust, I would have the parts on hand.

Now I'm wondering whether I already have the part I'm likely to need.

So far, I have bought:

1. Dorman Fuel Supply and Return Lines

2. Riff Raff Diesel High Pressure Crossover (HPx)

3. Riff Raff Diesel Fuel Rail Crossover (FRx)

So my question is, am I likely to have something to replace the part that commonly leaks on these trucks due to vibration/wear/chafing ... or will I still need to buy another part?

I'm thinking that one of the two lines in item #1 above is the problem child...

View 14 Replies

Ford - Escort :: Hard Start Up After Warming Up - Testing Fuel Injector For Leaking?

I have a hard starting condition after warm up. It starts up fine when it is cold.After running diagnostics and coming up with no error codes, I noticed that I smell raw fuel after the car was warmed up and sitting for about 15 minutes. I believe this is the cause of the hard starting condition after warm up.

How do I test the fuel injector for leaking? I think it may be leaking fuel into the throttle body after sitting for a few minutes, causing a rich or flooded condition which makes it difficult to start after it has been warmed up.

View 1 Replies