Ford 7.3L Power Stroke (1999-2003) :: Hard To Start Cold - No Codes
My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard Start When Cold / White Smoke
When it is cold out side like 20 degrees I'm having problems starting my 2000 7.3 I'm cycling it about 5 times and misses smokes white for a bit then stays running I was thinking of changing out the fuel filter. What it could be?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard Cold Start / Now EBPV Not Working
It's been a while but thats because the truck has been performing well.
Current problem: The truck has been hard to start this year as if the glow plugs are not working or are bad. It will start right up if I use the block heater.
Just recently, I also noticed that the EBPV is not coming on when warming up the truck.
Also, This winter season, the engine temp is not coming up to normal. the engine temp needle is more on the low side towards the C and definitely less than 1/2 way up where is normally is. When driving on the highway, the temp comes up more. but sitting at idle it barely gets warm.
So not sure if all 3 are related or not, but looking for a starting point.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Hard To Start On Cold - Oil Leaking?
20 degrees out this morning truck not plugged in, didn't want to start had to cycle 4-5 times, each time waiting for glow plug Light to go out.
Finally cranked didn't sound pretty but cranked. Once it started idling on its own got out and seen a puddle of oil under the front of the engine drivers side center kind of.
Got up on the truck and shined a light in the valley and seen a puddle in intake valley. Heres my question? Where did this oil come from? Once it warmed up it quit and oil kinda disappeared from valley???
I had turbo off a few months ago because I thought I had a bearing down in it, but found some bolts lose. When I put turbo back on I broke the wire plug on front of the pedestal so I just left it unplugged. Very hard to cold start now that that is unhooked.
Did leaving this unhooked create a hard cold start? Should I put another pedestal on it with the plug or install one without it? Also will it hurt to leave plugged in overnight?
Ford 7.3L Power Stroke (1999-2003) :: F350 - Hard Start When Engine Cold
2003 F350 7.3L 164k miles. Got towed in with hard to start cold complaint.
Hooked it up to the Snap On Verus Pro scan tool and we get up to 3000 psi on the ICP cranking, IPR value seems within spec, we have rpms over 100 on tool, pulse width within spec, computer voltage above 10v while cranking, verified output of glow plug module (California) and glow plugs get voltage for approx 50 seconds @ 80 degrees farenheit, glow plugs all read 0 ohms resistance.
injectors do NOT sound the same during buzz test.
Vehicle takes EXCESSIVE cranking cold to eventually get it started. LOTS of cranking. Just had to replace starter and a battery because driver burned em out. It feels like the vehicle shakes when it gets running. Black smoke when revving cold. Sometimes white smoke while cranking.
Once the engine has been warmed up, it starts perfectly every time.
I have spent two days in the engine bay looking for chaffed wires and doing diag and my current diagnosis is bad injectors. I feel there COULD also be high pressure oil leak, or a mechanical issue such as low compression. No compression guage yet for this truck. We have the ICP and IPR fittings to do a shop air test. Recently did a 6.0L and went thru everything and eventually diagnosed it as bad HPOP. LOW ICP pressure.
I noticed two of the cylinders were at maybe 8% Perdel on the data. Seems too high. Also, it "passed" the KOER self test and "passed" the injector buzz test with no codes after, but the audible sound of injectors didn't "seem" right to me, but I am new to these engines.
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start When Cold Outside But Eventually Fires Right Up
My 1999 F550 7.3L has been hard to start when it's cold outside since I got it with about 150k on it (it has 200k on it now). Last year we tested the glow plugs and sure enough 5 of 8 were bad. So they are all new now. It worked a little with the hard start, but not much.
When it's cold out the engine will crank forever amongst clouds of smoke and the smell of unburnt diesel fuel and sometimes eventually start, followed by smoke and sputtering until the cylinders clear out. However, what I have noticed recently is that it will sometimes start in the first few revolutions. It seems like the best way to start cold is as follows:
1. Let the glow plugs heat up for a minute or two,
2. Crank engine for 10 or 15 seconds and stop,
3. Crank engine again, but stop if it doesn't catch in the first couple of revolutions,
4. Repeat step 3 until engine starts.
When it starts using this method, it's immediate and it's running smoothly immediately with minimal smoke. This is making me think there's a computer or sensor issue, but I have no codes.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Hard Start On Cold - Temperature Sensor / PCM?
I have a 2002 f350 that has had cold starting issues since I bought it. I have replaced the glow plugs twice, the glow plug solenoid four times. When I put a new solenoid on it it works fine for a short time. I know the solenoids are bad because I get battery voltage on one side and nothing on the other. If I jump the solenoid with a jumper wire I can get the truck to start. I thought I was getting bad solenoids but I have recently tested the activation circuit and am getting constant power there. I.e. It never shuts off. I think this is what is causing the solenoids to burn up. From the tracing of wiring diagrams I have done, the only thing before the solenoid is the Pcm. So now to the question,
1) What controls the activation of the Glow plugs? Is there a temperature sensor or something before the Pcm.
2) Is this a case of my Pcm going out on me? I am a mechanic in the army so I have a decent understanding of mechanics.
However I am at a loss for these systems.
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start / Smokes And Running Rough When Cold
I have a 01 7.3 crew cab dually and it's had cold start problems since i got it in 09.I have replaced everything i could think of including glow plugs gpr,harness and batteries. Any temp below 40 i have to plug it in . If i cycle it 3 or 4 times it will start but it smokes and runs ruff. My 00 7.3 excursion starts up down to about 10 degrees than i have to plug it in so i know dually is not right.
I have a afe intake,1.5 injectors, driven diesel rr, adrenilin pump,dp tune by gear head. Kinda at wits end don't mind plugging it in in dead of winter but now one night it's 30 next it's50 and i don't have to . Also have fully built trans by level 10 if it matters .I get battery light coming on every now and again. New alt about every year and a half.
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start When Cold With Leaking Injector O-Rings
Truck is a completely stock 2002. New injector o-rings, glow plugs, valve cover harness, and injector cups a year ago... all motorcraft parts. New batteries and starter in the last 6 months.
I've checked the GPR both at the relay and harness got power all the way to the valve cover harness on all 8. Injector buzz test sounds okay as well.
Had a stuck IPR issue a few moths ago that caused a CEL and died while running. Took apart and cleaned the IPR and CEL is gone truck runs great once started and has correct IPR pressures in all RPM ranges.
Truck runs great once it is started and is not sluggish until warm like when it was hard to start when cold with leaking injector o-rings.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Hard / No Start At Cold - Injector Buzz
This is an issue I started chasing after having all the injectors replaced on my aunt's F-350. We had them replaced due to hard/no start on cold (dealership told her they needed to be changed). Unfortunately, I did not get the buzz test results before changing the injectors.
So far that has been replaced:
Injectors
ICP (was leaking)
IPR
both UVCH
IDM (twice)
The issue we are having right now is that only 2 injectors (#6, #7) buzz properly. Initially when we changed the injectors, it did start but didn't seem to run quite right. We did the buzz test and at that time and injectors 1,3,5,6,7 would buzz strong but the rest were weak. After some forum lurking, we suspected that the IDM was faulty. We purchased a refurbished one and after we changed it, only injectors 6,7 would buzz strong. Thinking a faulty IDM was sent it back for a replacement. While waiting, we decided to put the old one back in figuring it would go back as it was before but only 6,7 would buzz strong. We receive the second IDM and same thing, only 6,7 buzz strong. We did a continuity test from the IDM connector and they all get 2.7 ohms (it was an older multimeter so not sure if being .1 under the 2.8-3.6 range is bad).
What I did next is use the uvch external pigtail to test the injectors. I plugged the extra pig tail into the uvch and then the ends of the wires into the plug of the upper harness. Afterwards, I would swap a different injector wire (on the pigtail) to the #6 injector wire (on the upper harness). Whatever injector that would go to #6 would fire correctly. So I know that the injectors themselves are fine. I am suspecting the wiring harnesses (upper/lower) but the continuity test would say otherwise. We also do not get any fault codes except for the EBP occasionally (waiting for a new one). I am lost on what to test or look at next.
Ford 6.0L Power Stroke Diesel :: F250 - Cold Starts Fine / Stalls Immediately After / No Throttle Low RPM
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
Ford F-150 - 1997-2003 :: Hard To Start In Cold / Cranks Fine But Does Not Want To Fire
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Starts Hard / Bucking And Really Rough
If I don't keep her plugged in she starts hard, bucking etc. I'm thinking GP or GP relay but I`m not getting any thrown codes. Talking about *30-*50 outside, when its warm starts normally.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Hard Cold Start?
2003 Excursiom 4x4 Limited
My first Diesel. Runs and drives great. Torque Pro app only showed coolant temp at 188. Would not show oil temp. Hard to cold start. New injectors. Has a programmer. He is asking 12K. It has 209K miles.
It belongs to a friend of mine and he rarely drives it. It stays under a cover most of the time.
Ford 7.3L Power Stroke (1999-2003) :: Truck Turns Over Just Fine But Won't Start
I bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
Ford 7.3L Power Stroke (1999-2003) :: F250 Truck Ran Fine Now Won't Start
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 - Cranks Just Fine / Slow To Start
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
Ford 6.0L Power Stroke Diesel :: 2003 - Hard To Start And Runs Rough When Cold
My '03 6.0 is hard to start and runs rough when cold. Not just cold outside temps, but engine not up to temp. Starts and runs like a champ once it's up to temp. It was doing this when I got it, but it's getting worse.
From what I've read the common culprits are:
1 - failed solder joints on FICM power supply board
2 - bad power supply side of the FICM
3 - updated flash needed for FICM
4 - injector stiction
5 - leaky O-rings at high pressure oil rail to injectors
I have read up on how to run the voltage test on the FICM with a multimeter.
Seems like I would have to go to a dealer to have the software version for the FICM checked.
I am 100% competent to do the tests and/or repairs myself, but since I recently moved in with my fiance in a condo and my tools are in storage, I will have to do it at a friend's house. That being the case, I want to know what all of the common things are that I may need to check for so I am prepared. So, I wanted to see if there were any other common causes of this issue.
I plan to test the FICM voltage and give FICMRepair.com some business if that's the problem. And if that's not the problem (or maybe even if it is) I will get the injector seal kits and replace all of the injector seals as well as disassembling and cleaning the spool valves in the solenoids. I will also change oil and fuel filters with Motorcraft parts and Rotella synthetic oil while I'm in there.
Ford 7.3L Power Stroke (1999-2003) :: F250 Cranks Fast And Fine But Won't Fire Up And Start
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.