Ford 7.3L Power Stroke (1999-2003) :: F350 Died - Cranks Great But No Smoke Or Fire
While driving my 99 F350 7.3 it died and I was lucky enough to coast home. No WTS light, no tach movement when cranking, no fuel pump, no CEL, Cranks great but no smoke or fire. New CPS & PCM still no lights or tach. Moved relays checked all fuses. WTF is wrong?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Cranks But Won't Start
I have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Cranks Fast And Fine But Won't Fire Up And Start
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Cranks But Won't Run?
2002 Ford F250 super duty 7.3L Diesel Automatic I crank but wont start and run.
Background:
I live in NY, last winter (2013-2014) fuel pump stopped working, I discovered this website, changed my fuel pump although mine worked fine after I did it, Power was not going to my fuel pump, took apart truck to follow wires to find the problem, wires come from the fuel pump into the CPU and Fuse box, relay is built in fuse box, changed fuse box, truck started, from early spring to summer ran without problems, in summer friend ran truck dry without filling up luckily he threw it in neutral and shut off engine rolled it to a stop, Filled up truck after a few tries it starts up. A week later the fuel filter o-ring rips and spews diesel all over engine, changed filter ran for a week and o-ring poped out again, changed to a different o-ring and ran for a month without problems. Then poped again, and again, each time approximately a week later.
Latest winter (2014-2015)
I start my truck to warm up go inside and forgot all about it, about 1.5 hours later I remember my truck is started, go outside to find it shut off with diesel all over the pavement, the o-ring blew again. I changed it, cranked the engine and it started and ran for 10 seconds before stalling. I turned the key a few times to try and have my fuel pump run, and it would crank but not start. Then it started to crank really slow,(batteries were now already on charge) it was below freezing for a good whole week now, found my oil heating plug and waited a day, cranked it the next day, cranked faster but did not start, waited another day and when I tried to start it the starter would not turn.
Today:
So today, winter is almost over(if you lived here you would understand) I find out I blew my starter and changed it, I replaced the o-ring with [ 90025K557Double-Seal X-Profile O-Ring, Oil-Resistant Buna-N, Dash Number 347 ] from Mcmaster.com as suggested on this site. I cranked the engine, It started ran for 30 seconds and stalled. I tried turning the key a couple of times to get fuel going(fuel pump seems to be working), but crank and wont run. My father suggested starter fluid, got couple cans, I was able to start the truck with starter fluid and keep it running until the can ran out.
It wont start and run on its own like it did the first time I tried.
Ford F-150 - 1997-2003 :: 2000 2WD - Engine Cranks Great But Will Not Start
2000 F150 4.6L Romeo 2WD. Engine cranks great. Fuel pump working. Changed fuel filter. Will not start. No codes. Fixed A/C day before yesterday, only had air coming out defroster, disintegrated vacuum hose at firewall. Ran errands yesterday, no problems whatsoever. Get in truck today to go to work and no start at all, engine turns over fine. What next?
View 7 RepliesFord F-150 (2004-2008) :: Truck Cranks Great With Full Power But Won't Start
My 04 f150 has been sitting upwards in my drive way for a month now won't start cranks great with full power..
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranks But Will Not Start
Ive got a 99 7.3 with 250,000 miles on it. It has run fine all day but just jumped in and won't start. It cranks over but won't fire. Check engine light doesn't come on. About two weeks ago it cut off twice at idle but haven't had that problem since.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranks But Won't Start
I have a '99 7.3 that I am working on for a friend. He was moving out west and got to the next state. He stopped to use the washroom, when he came out, the truck would crank but not start. He had it towed back to my house. I have some diagnostic information. Fuel pressure measured at the fuel rail in the head is 60 PSI for the passenger side head. I pulled the plug on the drivers side, it was under pressure and sprayed fuel.. I did not measure it there.
WTS light comes on and then goes off in a normal time frame. Tach shows around 500 RPM while cranking. Engine oil pressure on dash gauge builds up and Low Press Light goes off. Pulled the plug on the High Pressure Oil Res., oil is present at the top. Are there any other checks that I can do until I can get a scanner. My friend has a Snap-On, but he's almost 100 miles away.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Stalls Out And Cranks Hard For 7 - 10 Seconds Before Starting
Truck stalls out and cranks hard for 7-10 seconds before starting if I don't let it warm up adequately before I start driving. Transmission is hesitant to shift. Also, white smoke comes out exhaust if it's cold and I get in the throttle too much or if I hit 70+mph.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Cranks But Won't Start?
I have a 2003 f250 with the 5.4 in it. When I bought the truck the odometer and fuel gauge weren't working. So I tried disconnecting the battery and when I hooked it back up the odometer started working again and the fuel gauge went from below empty up to full then just dropped back down to below empty and won't move at all. I haven't tried disconnecting the battery again. And I know more than likely I will have to replace sending unit but trying not to if I don't have to.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Cranks Over But Won't Start?
My '99 f350 lost a lot of power the other day, turned out the the injector harness got unplugged. So I swapped those out for oem ones, ohm tested the uvch and injector harness, put a brand new GPR, and still nothing. Cranks over but won't start, what else could it be?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Cranks But Will Not Start
This past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Cranks But Won't Start?
I have a 2002 f350 psd. I pulled it inside today to wash it. After washing it wouldn't start. Pcm is working. No oil pressure on guage and no reading on tach.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Cranks But Won't Start
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
Ford 7.3L Power Stroke (1999-2003) :: E350 Cranks But Won't Start
I have a 99 Ford e350 7.3 Powerstroke with about 150000KMS on the clock. However I am having a really hard time starting it in the Cold Canadian Winter (-30). Last week I changed all 8 glowplugs, the batteries, the oil, fuel, fuel filter and yes i always keep it plugged in.
It cranks really well, but it just wont fire not even with a shot of start fluid. I don't know anything about these trucks much less a diesel engine. A guy took a look at it and said my engine needs to b replaced. (I think he is wrong)....
Ford 7.3L Power Stroke (1999-2003) :: 1999 - Cranks But Won't Start - Water In Fuel Light On?
My 99 F350 cranks, but won't start, and the "water in fuel" light on the dash stays on while cranking. I have never paid close attention to it in the past. Is it supposed to be on while cranking?
I drained the water from the yellow lever located on top of the engine, and tried to start it. The light went off for the first few cranks, but again the truck still will not start.
I just came from a 10 hours round trip to NC. I filled the truck up two times from gas stations on the way. Is it possible that the fuel is bad? I drove on the same fuel almost 3/4 of this tank and now at the last 1/4 I am having this issue.
A little update:
I took the top of the fuel bowl off to see what the filter looks like, and it is nasty and completely black. I could not tell if the fuel in the bowl contained any water, but it looks greenish and uniform, no the obvious separation that happens when you mix water and oil.
Could the fuel filter be the problem?
A little history about the truck. It's always hard to start if cold and not plugged in overnight. I know it's the glow plugs relay, so I just keep it plugged in all the time until I get a chance to fix it.
IDM was acting up shutting off half of my engine, but I took it off, cleaned it, plugged it back in and it has been working fine for over 2 months.
Ford 7.3L Power Stroke (1999-2003) :: Cranks But Won't Start After HPOP Service
Removed and resealed HPOP and fuel bowl. Now she won't start. Ran fine before pump & bowl was serviced. I had leakage that I wanted to clear up. I have made no less than eight 15-20 sec start attempts with out even a cough. Reservoir is full, fuel in bowl and over 140 RPM when cranking.
AE info:
IPC duty cycle - rises to over 60% during cranking
IPC voltage - .18 all the time
IPC psi - 0 all the time
I did verify I placed the ball between the pump face and the "non serviceable" pin. I did leave out the spring and check valve seat from one of the output connectors. That has been corrected.
Ford 7.3L Power Stroke (1999-2003) :: Cranks But Won't Start - Relays Clicking?
So I have recently did a body swap on my 7.3 I rolled. Put a body from another one this one. Before I took the old body off the engine ran fine. Nothing wrong at all.
Now that I have the new body on, I am stuck with a fuel shutoff switch. I read that it is suppose to be pressed down, but when it is pressed down, I turn the key and 4 relays under the hood click rapidly, 2 under the dash, and the drive side blinker blinks? Anyway, when I push it up, and turn the key, all the lights come on normally, wait to start light comes on. It'll crank good, the battery's are good, had them tested and fully charged. Checked ando triple check all battery connections and grounds. Anyway, it'll crank and want to start it fire up for a second and die. The low pressure oil gauge on the dash doesn't go up, but I think I broke the sensor connector for that. The fuel pump doesn't make any noise, the fuel bowl has fuel in it, but does fill up with fuel. So I'm thinking the fuel pump is somehow shorted out, so when I depress the fuel shutoff switch it makes everything go crazy. But even then the fuel pump doesn't make any noise?
Ford 7.3L Power Stroke (1999-2003) :: Cranks / No Start Sometimes Stalls At Idle
1999 7.3l 6spd standard 4x4. Just bought the truck 4 months ago knowing it had a problem that once warm occasionally would t start. Happened a few times every week or two. But wait 15 minutes and the truck would fire back up. Then it started happening more often throughout a day. And I would have to wait longer for it to cool to start it up.
Icp has been changed
Cam sensor
Pulled valve covers to check to see if there were any injector o rings failing. They were all good. Put it all back together.
Pulled the IPR and tore it apart cleaned it all out
Started driving it ran great for a week. Then today sitting at a light the truck died just as if I had turned the key off. Wouldn't start for 3 hours. The. Fired up. Took it to buddies show and started checking things out again. Both batteries load test great and fully charged. Alternator pumping out 13.5 and up.
Codes i have pulled are waste gate to high /low
I forget the number for that one. The second was P1211. Cps has been changed and ipr cleaned. Think that I should replace the ipr of this happens again?
I did get w code a few weeks ago about low voltage at module. this code doesn't appear anymore. Since I checked the plug ins all looks good. But the PCM wasn't mounted properly. So I fixed that up and checked battery connections. They were very good so I re did all of that.
Anyway. Back to the problem. After ipr clean. Drove as she should until sitting at a light a week later. Truck just quit. Would t start back up until cold. Any thoughts. New IPR? Oil in hpop within half inch from top. And I don't seem to have any oil leaks. Did oil change fuel and air filter. Not low on any fluids. I had a 1997 too and threw a bunch of cash at it like this one trying to find the issues.