Ford 7.3L Power Stroke (1999-2003) :: F550 - Fuel In Exhaust / Gray Smoke Started Coming Out
Having trouble with motor, driving home one day heard a noise under the hood. Then a lot of grey smoke started coming out of exhaust. Got the truck hauled home notice fuel was coming out at the number 7 cylinder at exhaust port. Thought it might be the injector just put rebuilt ones in, thought I might have received a bad one. I switch the number 7 injector with the number 3 injector. Did not make a difference still have fuel leaking out of exhaust manifold at the number 7 cylinder and a lot of grey smoke coming out of exhaust. Not sure where to start looking next? Could it be the injector cup is the problem?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: CEL / Rough Running / Smoke Blowing When Cold
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
Ford 7.3L Power Stroke (1999-2003) :: F250 - Lots Of Smoke On Start Up
Alright. 99 Ford F-250 4x4 Ext Cab 287,000 miles. I know she is getting a little long in the tooth but this issue is new within the last month. It does seem to be better when it has been plugged in. On start up I smoke out the neighborhood. Blueish/White smoke, also sounds like it's missing on a couple injectors. Doesn't matter if you cycle the glowplugs a good long time. No luck. Glow plugs are 1 1/2 years old along with injector o rings. Only thing new is I changed from Rotella T-6 to Delo 5W40 Syn, but it was doing it before the switch as well. I tested my glowplugs relay and that is working fine. Could I have lost a UVCH? Fuel filter six months ago or so.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough / Started Blowing White Smoke
I have a 7.3 that's running rough. Started it the other day it ran alright but started blowing white smoke. Bought a oil and fuel additive i was going to run through it. Came a few days later, it stated up and was real loud and sounding like it was loping. It blew a good amount of white smoke, but it just smelt like real heavy diesel. Now i can only turn it over and it won't start.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Noticeable Miss And Lots Of White Smoke When Starting
1999 7.3 misses when starting it cold (first start of the day even when outside temps were around 20 deg C ). It has a noticeable miss and lots of white smoke. After warming up it runs perfect. I changed the GPR and tested all glow plugs, 3 bad and one weak one all replaced. Now that it is cold out it still misses when first started, even if left plugged in.
It will start and run for approx 3 seconds perfectly smooth then it starts to miss and idle speed slows down. on one occasion I went to start it after sitting 10 plus hours plugged in and it started then missed and slowly died. Would not re start, It was firing and smoking but not enough to get going again. Went back the next day and it started and ran fine for a few weeks. Did the same thing to me yesterday, started and then petered out and died and this time it will not re start after 2 days of trying on a couple occasions. I changed out the CPS with no luck.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 6.0L Power Stroke Diesel :: 2003 - Blowing Gray Smoke On Acceleration
I bought a 03 6.0 dually a couple months ago. Got a good price on it. I use it very little, around town sometimes and used to pull a 7000 lb camper sometimes. My issue is, the other day I took off with the camper. Drove for maybe 5 miles then stopped and waited for traffic. When I took off again it was blowing gray smoke when I was accelerating and had little power. I was going about 30 mph for about a mile at about 3000 rpm up a very gradual hill. I was in the tow setting. When I got to the top of the hill it seemed to recover. I pulled over and shut it off then took off again without any issues.
The next day when leaving camping it was the same thing. Took off and saw gray smoke and had little power. After about 1-2 miles all was well again. Truck has 202k miles. Recently replaced oil cooler, egr cooler has been welded shut at both ends, turbo has been cleaned and all the filters and fluids are new. I have a Scan Guage 2 and monitored the ficm voltage and it maintained 47 to 47.5 volts. I know 2 injectors had been replaced when I purchased it as well and the egr valve by a dealer(they said it showed the cooler was clogging but like I said it was welded shut). What I should look for?
Ford Super Duty (1999-2016) :: 2003 - Loss Of Power / Gray Smoke
I have an early 03 f350 with a 7.3 liter 298,000 miles on it
Replaced fuel filter
New oil change and filter replacement, New icp sensor .
Deleted the baffle and installed a cone air filter with the air sensor installed in the neck .
I Was driving home one day and the truck just slumped into this huge power loss . Couldn't get over 2200 rpms and barely made it over 30-40 mph.
Truck in park - idles like crap and still won't go over 2200 rpms when holding the pedal to the floor . And it has what sounds like a miss at a struggling "full throttle" (22-2500) rpms - thought it could be my icp sensor - replaced it -- no change
Checked driver side wiring harness -- no damage chafing found -- did a fuel can to pump test no difference - and today after I reinstalled the fuel line right after I ran my can to pump test I let the system prime . Started the truck and it ran for about 40 seconds and died and wound not fire back up and would just miss and spit and sputter -- lots of gray smoke though- but it fired up a few hours later after I let the batteries sit on charger .
Now before all this happened - I noticed the truck had a bit of a gutlessness to it as I would be piddling around around town and it would have this hesitation in power kind of like a slight jerking feeling , now this truck was so gutless since the day I got it ,I couldn't even burn out on a gravel road without the throttle going limp and the check engine.
Light kicking in so I figured I'd give it a bit of hotshots secret and see if It would maybe flush the injectors but it really made no difference...
Ford 7.3L Power Stroke (1999-2003) :: Intermittent Rough Motor / Black Smoke And Low Power
I have an Excursion with 220k miles. I've owned the truck for 6+ years and had very few problems. I change my own oil and fuel filters, but beyond that I know next to nothing about the diesel motor. I do run a DP Tuner with the standard 80 hp program. And a 4" exhaust. Everything else is stock. I do keep it plugged it for the oil heater and the battery tender just about all the time now.
This latest issue started yesterday morning when my wife jumped in a cool truck to take the kids to the dentist (not warmed up but still 55 degrees ambient). A few miles down the road (35 mph max) the motor began stumbling and rocking and black smoke coming from the exhaust with reduced power. She pulled off and kept it running (very rough and rocking) and put it in park for a minute. When she put back in drive, it shifted heavily but the power was normal so she went on her way without any problems. The only report I got sounded like the motor was just cold and rough, so I thought nothing more of it.
Yesterday evening we drove it about 70 miles on the highway (72 mph max) with no issue at all, but when we continued on surface streets toward our destination (50 mph max) it did the same thing, but would not settle back down. I kid you not that it went through gallons of fuel the last 12 miles or so, just dumping black smoke out the exhaust. It felt to me like we were running 1/2 the motor, like the plugs weren't lit. Very rough and rocking and very little power (comparatively, at least). I had to switch to manually shifting the trans to get going and the shifts were much rougher than usual. Idle was low and rough but it never stalled. Behind me there was a huge smoke screen this entire time.
We made it to our destination and parked it. Did our thing and after 5 hours went out with finger crossed. Started right up and ran perfectly the entire 91 miles home. No motor or trans issues at all. Currently running 10/40 synthetic oil that I just changed about 2000 miles ago. Oil level is perfect. 3/4 tank of fuel with standard level of Diesel Kleen added. Fuel filter is less than 10k miles old. Temps yesterday were 65-70 on the drive down and 50-55 on the way back.
I jiggled all sorts of connectors this morning and didn't find anything loose.
Ford 6.0L Power Stroke Diesel :: 2004 - White / Gray Smoke At Idle?
I have a 04 6.0l and all of a sudden it started dumping white/grey smoke at idle and when I drive it it goes to black then let off throttle and back to grey/white I had an up pipe leak at the y pipe I thought it might be an issue with that but I just got done fixing it and the problem still there so iam guessing it's either a sticky injector or the ficm but it starts up nice and does not knock around egr delete is don with all the goodies arp studs ect also the injectors have only 30k so it's hard to believe but iam just stumped haven't tested ficm yet and my tuner doesn't pick up any codes
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke / Rough Idle And Missing
I have a 2001 7.3 that almost has everything practically brand new... new hpop, water pump, uvch, gpr, glow plugs, icp sensor, ipr sensor, cps and new turbo pedestal that was leaking oil, well now my truck has a cold start to where it has to be plugged in to start and when it finally does it smokes white pretty bad, misses and sounds like it's jumping around under the hood up until it warms up and revs fine with less white smoke but still a miss!!
Compression on test has been done, and good, fuel pressure is good, but the buzz test when cold shows 123457 muffled and quite and when the truck is warm only 3 and 4 are still muffled and quite? Injectors sticking?? Or just need New injectors!
Ford 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Running Rough - Missing - No Power
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough And Had No Power / Died While Driving
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
Ford 7.3L Power Stroke (1999-2003) :: Rough Running / No Power After Just Driving A Block Or Two
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough When Accelerate / Bogs Down And Looses Power
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough And Cannot Pull When Put It In Drive
I bought a 99 7.3 been in the trees for a few years pulled it home and now trying to get it running. Did a service new filters and oil fuel too. I can get it to start and will run but runs very rough and if you put it in drive cant pull its own self. I don't have a check eng light on. And found out my scanner is a pos lol. it will hooked up and then try to pull codes and loses it connection. But that's the scanner will not work on my other 7.3 as well.
I am making high pressure oil checked off the rail with gauge and it will build up to 2000 psi when I rev it. but missing like crazy. I swaped the pcm and idm out of my running 7.3 and it didn't change a thing. I have checked the pass though and they are fine. pulled drivers side valve cover off and no oil leaks when running and rockers are fine. new ipr valve as well too. I know I need to get a scanner to talk to this thing better.