Ford 6.0L Power Stroke Diesel :: 2004 F250 Starts Fine Then Dies After 2 Minutes

I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.

My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.

I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???

IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.

ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts

ICP pressure Start 900+
Idle 830ish

Sync between CAMshaft and Crankshaft is 1 = good

Have not gotten fitting to do fuel pressure test yet.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: F250 Truck Ran Fine Now Won't Start

Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: F250 Stall After Starting And Running Fine

I have a 1995 f-250 7.3 liter diesel engine. Truck starts fine and runs good for a while and then it will stall. I pull over and after a couple of attempts it will start and run fine for a while. I have changed the fuel filter and put fresh fuel in but it still stalls.

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Cranked Fine But Would Not Fire

Owning a 2001 F250 Extended cab with a 7.3 I have not had a lot of questions to ask fortunately.

My truck has spent a lot more time sitting than running lately and when I went to start it the other day it cranked fine but would not fire. Quick read on this forum and the first thing I found was how if the fuel solenoid had less than 10.8 volts when cranking it would not start.

I went down and checked the battery voltage and it was at 12.1 volts no load. I put the battery charger on for about 10 hours (time to kill) and when I pulled the charger and cranked it over, started with no problem.

View 3 Replies

Ford 7.3L Power Stroke (1999-2003) :: F250 Cranks Fast And Fine But Won't Fire Up And Start

My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.

I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Idled Rough After 2 Minutes Then Stalled Now Won't Start?

So I went out this morning to start the truck up like I do every morning. It cranked once, and didn't start, which is somewhat normal. second crank it started right up, which is normal, then after about 2 minutes, it seemed like the rpms were bouncing and the engine got a little more slower and louder, then it dipped below 500, then stalled. After that moment nothing. It just cranks. Now it was VERY low on fuel, I've been this low on fuel and never had anything like this happen, so my neighbor took me up to the station and I bought 2 gallons. came back, still nada. I went out after letting it sit on the block heater for about an hour and noticed a small puddle of fuel under the truck on the passenger side. I went to start it and the fuel gauge went up to a half tank. cranked, no start. then again and it went up again but slowly started creeping back down.

Now the kicker, I have very limited knowledge of diesel engines, or gas for that matter. So if my intuition is right, this is probably going to be a learning experience for me... what should I check first guys? Its plugged in right now but I am sure that's not gonna fix it.. I am gonna change the oil first since it needs it, I bought shell rotella triple t 15w40 which im assuming is ok. last winter It was leaking fuel when it was really cold out but that was it, just leaking a bit and then after spring it went away. I know I should have fixed it when it started but I have an extreme anxiety to letting any mechanic near my vehicles and just about as much anxiety trying to fix it myself. I'm at a loss for what to do, I'm a pro with computers but this truck scares the crap out of me, I'm terrified I'll do something worse.

2002 Ford F250 Powerstroke 7.3 4x4, 218,000 Miles....

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Codes P1247 And P1248 / Noise Sounding Like It Lost Air Compression For A Few Minutes

My pickup has 316,000 miles on it. It's a 2000 ford f250 7.3 powerstroke. I have always bragged how my truck can pull anything because it has alot of power. Yesterday when pulling a 28' travel trailer up an incline I noticed I didn't have much power and it steadily got worse. Now I'm at a crawl when I hear a noise sounding like it lost air compression for a few minutes then the noise stopped. I stopped and looked to make sure everything under the hood was still attached and everything seemed fine.

I got back in and continued very slowly a few more miles home. Gauge were all good, never got hot. I put a scanner on it and it threw two codes. P1247 and P1248. I haven't noticed any unusual smoke. This is my second ford I've owned and know that when weather gets cold you may have to plug it in. But this truck it doesn't matter if it's 100 outside it will not start without plugging in for at least 1 hour. I've replaced all glow plugs hasn't worked. So I am assuming this break down now has something to do with it. I really am starting to not like fords!

View 13 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To PCM Fuse

I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....

KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.

I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?

Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.

My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).

Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power Getting To Fuel Pump

There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Accessories Come On

My 02 F250 periodically has no acccesories like electric windows, radio, and AC do not work for a minute or so. It has been doing this for awhile and seems to be getting more frequent and I am concerned that it might go out on a trip. It runs OK when this is going on and usually happens on the first start on the day. I was thinking maybe the ignition switch?

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Cranks But Won't Run?

2002 Ford F250 super duty 7.3L Diesel Automatic I crank but wont start and run.

Background:
I live in NY, last winter (2013-2014) fuel pump stopped working, I discovered this website, changed my fuel pump although mine worked fine after I did it, Power was not going to my fuel pump, took apart truck to follow wires to find the problem, wires come from the fuel pump into the CPU and Fuse box, relay is built in fuse box, changed fuse box, truck started, from early spring to summer ran without problems, in summer friend ran truck dry without filling up luckily he threw it in neutral and shut off engine rolled it to a stop, Filled up truck after a few tries it starts up. A week later the fuel filter o-ring rips and spews diesel all over engine, changed filter ran for a week and o-ring poped out again, changed to a different o-ring and ran for a month without problems. Then poped again, and again, each time approximately a week later.

Latest winter (2014-2015)
I start my truck to warm up go inside and forgot all about it, about 1.5 hours later I remember my truck is started, go outside to find it shut off with diesel all over the pavement, the o-ring blew again. I changed it, cranked the engine and it started and ran for 10 seconds before stalling. I turned the key a few times to try and have my fuel pump run, and it would crank but not start. Then it started to crank really slow,(batteries were now already on charge) it was below freezing for a good whole week now, found my oil heating plug and waited a day, cranked it the next day, cranked faster but did not start, waited another day and when I tried to start it the starter would not turn.

Today:
So today, winter is almost over(if you lived here you would understand) I find out I blew my starter and changed it, I replaced the o-ring with [ 90025K557Double-Seal X-Profile O-Ring, Oil-Resistant Buna-N, Dash Number 347 ] from Mcmaster.com as suggested on this site. I cranked the engine, It started ran for 30 seconds and stalled. I tried turning the key a couple of times to get fuel going(fuel pump seems to be working), but crank and wont run. My father suggested starter fluid, got couple cans, I was able to start the truck with starter fluid and keep it running until the can ran out.

It wont start and run on its own like it did the first time I tried.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - CEL Came On For 30 Seconds And Went Off

I have a 2002 F250 7.3 with 130,000 miles. The truck was bought new by my father and is completely stock and never run hard. I was driving on the interstate at 70 mph and the cel came on for 30 seconds and went off. Not long after it went off the truck shut off and has not started back. That was around 12-20-16. I have put a new cps, icp, and ipr on it with no luck. All ford parts. I drained the fuel water separator to check the fuel pump and it filled back up. The truck is turning over good but has no white smoke witch leads me to think maybe the IDM. I'm a novice to all of this and until this happened new nothing about any of these parts but I'm learning. I do have the torque app if I should check some things.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power To Reverse Light Sockets

I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Lost Power And Suddenly No Throttle

Comming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.

Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power

2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.

I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.

I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.

I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.

What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes

I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts But Have No Throttle

My 2002 f250 starts but has no throttle, I did replace the throttle body, still no luck, i did find a wire on the shiffter that had a bad spot , fixxed it still no throttle, code reader says it passes with no codes, I disconnected both batteries and waited 15 to 20 min, reconnected them, started the truck and let it idle for 20 min so what do i need to do now. I just cant figure it out....

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Surging Between 35 - 50 MPH And When Coasting At About 60

Ran torque for the first time on my f250, I used it for diagnostics to see if i can find out whats causing the surging. At a red light sitting idle it shows my icp at 705psi seems high to me? I'm running a dp tuner, it was set at stock for this run. It starts surging between 35-50mph and when coasting at about 60mph, surges during light throttle or maintaining throttle at low speeds. If i go about 70mph and up it runs like a champ. Ive changed the tps(entire pedal assembly), uvcg connectors, icp and pigtail. No CEL comes on, torque shows ipr is good, working on hpop pid. I just bought the truck last month and haven't been able to enjoy it much since it started doing this. ...

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Changing Air Filter?

my first diesel, and second 2002 f250. I picked up my 7.3 4x4 automatic CCSB last week. 202k on the odometer. I need to change the air filter but idk what to use. I don't think it's stock. The side of the air box says aFe. What the part number for the filter is? I don't see one on the filter anywhere.

View 6 Replies