Ford 7.3L Power Stroke (1999-2003) :: HPOP Leak Repair?
Do I have to remove my fuel filter and bowl to attempt a repair on my HPOP leak?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Cab Repair - Use Entire Cab Corner?
My crew cab got T-boned last week and I'm looking for parts to fix it if insurance keeps messing around. Is it possible to use the entire cab corner from a regular cab instead of a crew cab?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Repair Of High Oil Use And Long Crank?
Parts came from Riffraft Diesel Performance. A set of "o" rings for the injectors. High flow CVD fittings for the fuel lines. Turbo rebuild kit. (its got 210,000+ miles) Anti Surge compressor wheel.(ok its not part of the oil problem)
Photos to come. I will take during the rebuild.
Ford 7.3L Power Stroke (1999-2003) :: ESOF Hub Clicking - How To Repair / Rebuild
I was hearing a clicking noise on my passenger front wheel when rotating by hand.
Paul suggested I remove the ESOF hub and see if it is the wheel hub or the ESOF hub. It's the ESOF hub.
So I'd like to rebuild it for sure, it also has a nicked o-ring, so that accounts for part of the vacuum leak
I'd like to service the driver's side, too, while I'm at it. It doesn't exhibit any issues, so just regular maintenance stuff there.
Parts lists?
As always, I'll take pics in return
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Code P0720 Only On 4 - 6 PSI Launches
2001 7.3 Excursion, full mods in sig line.
Recently started getting a P0720 for OSS on 4-6 pound launches, and the X will lurch and then stall out. It drives fine when I drive like a normal person, it also launches fine at 8psi and up (obliterates the tires in the process). Little curious as to where I should start looking beyond the usual culprits on checking the connector for corrosion and verifying the sensor itself is clean/still good.
Stupid thing drives like a peach everywhere else except the 4-6psi LAUNCH ONLY range. Normal driving through that pressure range is absolutely fine. 4-6 is the only problem child area.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Got P1832 Code - Flashing OD Off Light?
I have a persistent issue with the OD off light flashing on my 2001 7.3L auto 4x4. Scanning it with AE I get the P1832 code. The truck runs and drives just fine. It shifts nice, goes into overdrive, locks up, etc. If it weren't for that blinking light I'd think it was all perfect. I've checked all the connections, replaced the range switch / neutral safety switch, replaced the VSS on the rear axle, checked all light bulbs and fuses. I've checked MOST of the relays in the truck.
I pulled the tranny drain plug and poured out a bit of fluid into a clean pan, it looks and smells good. AE also tells me that it's not communicating with the ABS system (although there's no persistent ABS warning light on the dash), the Airbag, the Overhead Trip Computer, the Parking Aid (which I don't have...), or the Enhanced Powertrain. The temperature on my overhead display is reading -40F which is clearly wrong.
I've looked for a comprehensive wiring diagram for the truck, but can't find one. I'm trying to figure out if there's a connector or module that these various functions go thru that might be the problem. Am I missing a ground somewhere? The frame was just powdercoated......am I not getting a good ground connection? In complete disclosure, I have torn this truck apart and re-assembled it out of several different trucks as outlined in this thread.
[URL]....
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Idling Like Going To Run Out Of Fuel / Bad ICM Code
I have a 2001 f250 7.3. Recently started this problem idling at 1000 Rpms when stopped completely and when I let off the gas pedal it idles real funny like it's fixing to run out of fuel. It does not do this all the time however. At times it runs great. I had my mechanic scan it and at first it was the exhaust pressure sensor. Replaced it and it ran fine for awhile and it started doing again. Took it back in to get re scanned and it was throwing a bad ICM code. Replaced this as well and I'm still having the same problem. Had it scanned again and it's not throwing any codes now. I have no check engine light on and as long as I'm on the gas pedal it runs great. It's just when I roll up to stop or when I'm stopped completely. Again it does not do it all the time.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - P1247 Code Pending
Alright I have a 01 F250 with the 7.3L in it. Recently had the turbo rebuilt and all the surrounding gaskets changed as well as boots. All this was done around 1,000 miles ago. Runs great and I don't see/feel any issues, no white smoke anytime, little black when I turn up the tuner and really ride the thing but normal driving none. Problem is I have a pending P1247 code that after a few days will throw a CEL... I'm not sure what the problem is and have been searching the forum and people are mostly saying they get it but the boost drops or there isn't any at all and the truck my stall or bog down. I don't have any of those problems. Turbo spools up to whatever I want and I've never had it stall or bog or even get close... So what should I check? Also new to the site and diesels.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Airbag Indicator Light On For Code 47
About a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
Ford 7.3L Power Stroke (1999-2003) :: Way To Repair A Switch On Driver Side Master Window Switches?
Is there a way to repair an individual switch on the drivers master window switches, or do I I have to replace entire 4 switch and window lock set?
View 8 RepliesFord F-150 (2004-2008) :: Getting P0605 Code Every Now And Then / PCM ROM Error
I just bought a F150 with 103,000 on it. The engine is a 4.6. I get a P0605 code every now and then which doesnt effect performance. I erase the code and it doesnt appear again for maybe another 100 miles.
I suspect a loose connector but not sure. Looked up the code and it reads PCM READ ONLY MEMORY (ROM) ERROR. My question is what does the PCM operate? And wheres a good place to start troubleshooting?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford F-150 (2004-2008) :: Error Code P0605 After SCT Tuner Install
I recently changed from a problem-ridden SCT Livewire to a SCT Xcalibarator3, and now when running my custom tune I get a check engine light and a error code P0605. I never got this on the same tune with the Livewire. What causes this and how to fix it?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: No Power Suddenly - Got Code P1316?
Here's the story. Truck has showed no signs of rough running. Wife drives truck around town. Truck up to temperature and doing fine on a 90 degree day. Stops at red light. Makes left turn engine light comes on truck seems to be running on 4 cylinders. Pulls over light goes off engine idles perfect. Pulls back on road light on no power. Gets truck to a local friends house lets it sit til I get off work.
I check for codes get p1316. Drive truck toward my house no problems for 4-5 miles then does the above with me. Limp it home. I know it is pointing at a wire problem to injectors and or IDM. Did a buzz test passed fine. Plan on pulling valve covers and looking for the usuall things. Any thing I am missing? What will a kOEO test tell me? Should I run one? How common is IDM to go out? One last thing just put a rebuilt transmission in it 3 days ago may be unrelated it seems to be doing fine.
2003 f-350 cc 7.3.
Ford 7.3L Power Stroke (1999-2003) :: Pop When Accelerating With Turbo Spooling Up And Lost Power - Code P0475
As I was getting ready to leave town with the tractor loaded up, I was accelerating with the turbo spooling up when I heard a bit of a pop and lost power (engine still running and all, just very low power like you get when the turbo fails). I wasn't far from the shop so I came back and started getting a lot of white smoke out of the exhaust, it doesn't smell like diesel, probably more like oil. Definitely smoke, not coolant. I pulled it around back and shut it down to go grab AE and scan it and it shows a P0475, starting it back up has light smoke at idle and it idles fine but as soon as you give it any throttle it starts smoking pretty badly.
Researching it looks like the most likely cause for this is the EBPV itself but before tearing it down that far. This is the only code it's showing.
Truck has 272k on it, turbo was rebuilt a couple of years ago but we didn't do anything with the pedestal at that time. I guess in retrospect, I probably should have done the EBPV delete and the resistor fix then but I didn't think about it at the time.
On another note, my AE is not showing any of the system test for some reason, the drop down is blank. I have version 7.0.1, so it's an old version but I'm working on an old truck, so... What that might be? I've got the truck pulled into the shop now to let it cool down. I'll probably let it sit overnight and take the turbo and EBPV out tomorrow unless someone has a better suggestion...
Ford 7.3L Power Stroke (1999-2003) :: Code P1316 - New IDM?
What do I do? Do I need a new IDM?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Won't Start - Code For EBP?
Truck was towed into my shop for no start. Mechanic diag as hpop pump. He is no longer here. R&R hpop with thourobred reman pump. Truck still a no start. only code is for EBP. Spacer is behind tin nut of ipr. Starter spins motor as it should. No blown fuses. WTS light works. No oil in icp or ipr sensors. GPR voltage is good. Tach moves when cranking. Disconnect ICP still no start and has 65% duty cycle. IPR has 500-1000psi the first 2sec of cranking then it drops and fluctuates 180-480. Add direct power to ipr and get 660psi the first 2sec of cranking then drops
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P1249 - Boost At About 20 PSI
I disconnected the red wastegate hose in order to address a low boost high EGT issue. This seemed to fix the boost / EGT issue for the most part, but now I get this P1249 code. The first time I got it I saw boost at about 20 PSI. I figured I would try to keep the boost below 20 in an attempt to prevent the code.
I managed to capture some log info when throwing the code. The highest boost reading I saw was 19.58. Pretty close to twenty but I question if I even should be getting this code at this level of boost?
Here's a chart with the boost info. Yes I still have a very bouncy EBP and hope to track that down at some point as well....
Ford 7.3L Power Stroke (1999-2003) :: Error Code P0475 - Fix?
I went and got my truck smog and it failed because of this code. I then changed the sensor cleaned out the tube and I still can't figure out how to get rid of the error code?
View 3 Replies