Ford 7.3L Power Stroke (1999-2003) :: High Beams Only And No Low Beams After Installing New Headlight Bulbs
I have checked fuse 46 and 47, and installed new headlight bulbs. I have high beams, but no low beams. I have searched this topic but no one has the same prob it seems. My headlight switch has broken. Could it be the headlight switch?
In my manual, it says the 2002 has a fuse panel behind the glove box. I took glove box out but it doesn't look like a fuse panel.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - High Idle While In Gear / Stay At 800 RPM
So finally got my truck running due to a fuel issue. Anyways been driving it for a week or two now, and I have a strange problem idk if it has been covered here or not.
Driving around tow etc if you come to a light or whatever and stop the rpms stay at 800rpm. Now if you shift it out of gear and back into drive the rpms settle back down around 650. Where is should be.
My guess is the torque converter is not disengaged all the way when it stuck at high rpm (800-900) for this situation. No cel, slippage, or crazy noises
2002 7.3 power stroke all stock right now @160k black crewcab
Previous owner had a tunner on it but not anymore. Could it have smoke the trans???
Accent RB (2012+) :: Low Beams Stay On With High Beams
The other night on my way home, I flipped on the high beams and the low beams didn't shut off. Flash to pass still works, and pushing in on the end of the stem turns the low beams off as well.
Having the column switch apart, is it possible this could be fixed without having to pull the steering wheel? Or, am I better off just spending the hundred dollars of so and putting in a new part?
Ford Super Duty (1999-2016) :: 2007 F250 - High Beams Stay On After Projector Upgrade
I just had some custom headlights built for my truck. I have noticed if I am on low beam with fogs on, switch to high fogs go off, switch back to low, and fogs come on but highs stay engaged until I turn off fogs, the go low beam... I have heard this has happened before with other trucks and that it was called a Bambi something? And that there was a possible fix...
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Bad Miss Or Stutter / Knock At High RPM And Deceleration
2000 F250 7.3L ZF 6spd 4x4 regular cab long bed 253k
DP F6 chip, 4" exhaust, WW2, EBV delete
I run 5w40 Rotella Synthetic. Oil was changed about 1,000 miles ago. I also added a quart of Hot Shot stiction eliminator. I use Power Service and Stanadyne lubricity in every tank. Fuel filter is new.(motorcraft)
For a month or so its been acting weird. I get a stumble/miss/stutter, at random, but mostly under hard acceleration and high rpm (specifically approx 2500-2800rpm). It will also do it on decel when I lift after accellerating . Recently, I noticed it is also idling roughly. The engine is shaking and it feels like a miss. When it does its "thing" it sounds like a single "knock". Occassionally, it sort of sounds like an injector "buzzing". I've been using the "stock" tune for the last few weeks, to minimize any chance of engine damage, as I have to drive it. Turning up the chip makes the problems more noticeable and happen at a lower rpm. The truck has plenty of power, and pulls hard, except for the "stutter". If I hold my foot in it to "push through" the initial stumble at 2500 or so, it will keep going a few hundred more rpm, and then really start bucking.
There are no meaningful codes. I DO have:
EBV related soft codes - makes sense since its deleted.
Overboost related codes- from turning the chip up - won't happen in stock setting
A soft code for the back pressure SENSOR. I have a new one and will be cleaning the tube when I get a chance. I unplugged the sensor and it made no difference in the miss issue.
I have recently done the following in pursuit of a solution to all this:
New IPR (autozone) valve and pigtail
New ICP (motorcraft) and pigtail ( sensor had oil in it)
New CMP and pigtail. (2 actually. First a standard pc139 for the obs, and currently a Napa echlin correct for '00) No change. Although it initially had the dreaded Ford small head light grey sensor and failed cct for #3 & 8. After the cps change, it passed cct.
Accellerator Pedal Position Sensor. It would not read any higher then 3.95v at wot, and only 0.50v at idle, so I installed a new one. After adjusting it a little, I have 0.76v at idle, and 4.02 at wot. Didn't affect the stumble issue, but it seemed to greatly improve/eliminate my parking lot speed "bucking".
I just did the UVCH's. The passenger side was pretty much unplugged. But they all looked good. No burnt, melted,or chafed wires anywhere. I probably could have just plugged it back in, but I changed both sides with new Motorcraft parts anyway. I did the gaskets and the uvch, but not the engine side harness/pigtail, as they looked ok. I also did the 0.50 mod as a preventative measure. After seeing the unplugged harness, I really thought this would be the end of the problem, but its not. Very frustrated.
As a side note, I was surprised to see that I have 8 AD injectors, and not an AE in cyl 8.
I have an old outdated snapon scanner. Its only good up to '99, but I am able to scan my 2000 as a '99. I think I'm missing some pids though.
I can do cct and buzz test, but no PERDEL readings.
As far as ICP, it idles at about 450psi, at approx 12% IPR dc. On a brief 2nd gear wot run, it will hit (and hold as long as I have road to stay in it) a little over 2900psi, at 41-42% IPR duty cycle. I did notice, during these near instantaneous stumble events, ICP would flutter on the scanner about 75-100psi. Its almost too quick to even see it.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - High Idle / Over Drive Light Started Blinking
OK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
Ford F-150 - 1997-2003 :: Low Beams Don't Work But High Beams Do
I recently installed new halo HID headlights in my 2003 f150 with HID bulbs and ballast the passenger side worked and the drivers side didn't nth lights wired exactly the same. I switched everything from the passenger to the drivers side still nothing I switched everything back to passenger side and they don't work now. I tired regular bulbs in the passenger side an it worked then on the drivers side and it worked for a split second and went out and then I retried t on the passenger side and it worked for a split second and went out a now neither are working. I checked all the fuses and their good. What the problem could be?
View 5 RepliesFord Super Duty (1999-2016) :: Truck Only Has Low Beams / No High Beams
My truck only has low beams. When you move the stalk on the colum backwords it changes nothing, when you move it forwards the low beams go out but the high beams do not come on.
View 14 RepliesPassat (B6) :: High Beams Don't Stay On
My regular beam light stopped working today. If i pull back on the high beams, both come on and work, however, if i push the lever forward to leave them on permanently, they don't come on at all. Is this because the regular bulb is out, or is something else wrong?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Headlights To Stay Off When Key Is In On Position
Is there a mod that allows the headlights to stay off when the key is in the on position. 2001 F250....
View 6 RepliesFord 6.7L Power Stroke Diesel :: Wiring Some Light To Activate High Beams?
Just wiring up some light on the front and want to activate the relay off my high beams.. Where the best place to hook into... I'm running it off number 1 upfitter switch. But also want it connected to the high beam switch as well.
View 12 RepliesTiguan :: 2011 - Cannot Get High Beams To Stay On?
I just bought a 2011 Tiguan S. Loving it so far, but I can't seem to get the high beams to stay on? I'll pull on the lever and it'll go on but then will snap back. I thought it was strange since none of the cars in our family does this. I tried turning it on with the headlights turned on as well and it wouldn't work.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Hard To Start And Won't Stay Running
What's up power stroke fam. I have a 1999 F250 Super Duty 7.3 liter this is what happen, was leaving the job site the truck started just fine ran for about 3 city blocks stopped at a stop sign and it started to run ruff like it was out of fuel but had a half tank then poof it shut off. After towing the truck home and trying to start it I could hear a relay clicking very sporadic the service engine light came on then when off and the truck started and the exact same thing happened started running ruff and shut off. Where should I start other than taking it to the shop?
View 14 RepliesCamry :: 2007 - High Beams Stay On All The Time Even When Car Turned Off
I love this car- i just bought it , but it has one problem i cant figure out .The high beams didn't work at all -till my mechanic figured the prior owner took out the two fuses - now they stay on all the time - even when the car is turned off . My guess is the light switch - my mechanic said it is probably more than that...
View 3 RepliesLexus RX 2004-09 :: How To Modify Fog Lights To Stay On With High Beams
What steps are needed to modify a 2005 RX 330's fog lights to stay on with the high beams? I found the info on the web & did this modification to my 2010 Tundra but can not find any info pertaining to how to mod an RX.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Clutch Pedal Goes 1/3 Of Way Down - Drops To Floor And Stay?
I just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: High Pressure Power Steering Hose
My high pressure power steering hose just blew at the "B" nut at the pump. Meaning, the fitting is still in the pump but the line is out. Do I need to replace the whole line or is there a retainer I can swap out?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: High Pressure Power Steering Line Blown?
I just replaced my 3rd HP power steering line last night( 3rd in 300K, always blows the same point....fitting comes apart where it attaches to the pump.
I'll start, mine have gone about 100K plus or minus 10K, almost thinking about making it a 100K maintenance item.