Ford 7.3L Power Stroke (1999-2003) :: 2000 - Ignition Relay Location?
I purchased one of the No Start relay for my 2000 Ford F-250 Turbo diesel and need assistance finding the relay to replace.
Originally I thought it was for the fuel pump then then discovered it replaces the ignition relay.
According to the company it's located on the passenger side under the hood. Can't find any fuses there.
I looked in the user manual and found nothing about an ignition relay. Just "PCM Relay Coil, Ignition Coil (Gasoline only), Fuel Heater (Diesel only), Wastegate Solenoid (Diesel only), Injector Driver Module Relay Coil"
The relay I purchased is from: "No Start" Relay, "No-Start" Intelligent Relay System, Vehicle Theft Deterrent
Ford 7.3L Power Stroke (1999-2003) :: Battery Light On / Voltage Meter Only Show Barely 12 Volts At Full Throttle
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
Ford 7.3L Power Stroke (1999-2003) :: Some Gauge Reads Towing Light
Towed 3 axle trailer loaded with a 73 VW bug, two implement bars, plows and a small boat. I would guess total weight at 7,000 max. The ambient temp 97 degrees and very humid. I have a 2000 dually.
The following are from the ScangaugeII
TFT trans temp 175 max
EOT end oil temp 205 max
SLP trans slip 0.20 max and 0.0 in high gear
From glow shift
Water temp 196
The one I am worried about is the trans slip, from a stop taking off always went high 0.15 to 0.20 and then drop quickly. Once the TC locked 0.0 down the road. Also, when I reverse with no load on dirt I have seen 0.20 on the trans slip. I have Forscan but have not logged any temps yet....
Ford 7.3L Power Stroke (1999-2003) :: 1271 Injector Code - High Side To Low Side Open Cylinder 1
I've got a 1271 code and I can't seem to make it go away. Code definition is "High side to Low side open Cyl 1". The truck runs fine, no rough idle, no excessive smoke of any color, just the damn CEL light stays on. I check the UVCH and all the injectors ohm in at 2.7 ohms. I've already done the updated clips under the covers. I run all the buzz tests and KOEO/ KOER tests and all appears OK. My AE won't do a Cyl contribution test. All the injector data shows all 0.00. I know its not that perfect. "high to low open", does that mean I've lost a ground? If so where?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Got Error Code P1464?
Well I thought my truck was 100%, and I was going to installed a Chip. I decided to get my Forscan up and running to check and make sure.
The Buzz test Passed with no problems.
The cylinder contribution did not pass. I got error code P1464, which Forscan said that #8 failed. FYI, I turned the A/C on and the test failed. I ran it again with the A/C off and it failed again. I might have the wrong code
I then went to where you could select the gauges to view(PID's). And I saw where you could select all the cylinders injectors individually. I forgot what it was called, but all injectors were reading close to 0.0% at idle except for #8 it was reading 5.55% to 5.88%.
I am hoping this is good news, since I rather the injector be bad then a piston ring or valve. I just got the Forscan and was wondering what other test or other things I could check to narrow the problem down before removing the Valve covers. The truck runs great and there is no miss and it turns over smooth. No blowbye, just runs great. It is a 2000 F-350 dually with just over 202,000 miles
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Sluggish - CEL On - Code P1316
Just a heads up when it comes to this code. Today at work I was working on a 2000 f350 that the driver neglected on telling me he had a CEL on and truck was kind of sluggish (drivers are idiots they cant tell the difference) but no miss or any sign of problem except the CEL (he had electrical tape on the cluster. Well I put my AE to see the vitals and immediately code p1316, so I went to do a buzz test revealing that cylinder 1,3,5,7,6 were short to open circuit (forgot the codes) but they all sounded healthy. My next step since it was a quick and easy to do was to check the passenger side uvch to see for burnt pins and what not but everything checked out.
Checked the driver side #6 cyl for the same problem bit a no go. I ohm tested the injectors all of them checked out, wires all the way to the idm checked out so at this point I was in my atemp to see what the hell was going on I decided to install my obs idm on, and guess what happened next it worked immediately the sel did not come up and when I test drove it, my god it felt like a new truck.
Just a side note the idm, had no sign of water damage, and like mentioned to the untrained person most would not tell the difference on how it ran. To anybody that has checked and can't find the problem make sure you really and I mean really check your IDM really good.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Error Code P0472 - Low Boost / 0 PSI EBP?
2000 truck, 334k, automatic 2wd, stock. Have low power, 11psi max.
Permanent p0472 code, can't clear it even temporarily. The moment I turn the key to Acc, code is there. It's the only code showing on Forscan.
Tried 470ohm 1/2watt resistor, in two turbo pedestal sensor connector wires, no change. Forscan shows 0.0-0.6 psi EBP value when running.
No change with pedestal sensor plugged or unplugged. Resistor or not. Truck starts and runs good, low power is the only issue.
Sensor and tube are new. Seems like wiring is bad, where to look next to track this down?
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Got Code P1316 - Injector Wiring Harness?
I have a 2000 Ford F550 7.3. I bought a Superchips programmer to read the codes on my truck and up pops this P1316, so I did some research and found out that the most common problem is the injector wiring harness. I bought new valve cover gaskets and the injector wiring as well because the truck is old and I figured new wires wouldn't hurt.
So after installing the new wiring harness and gaskets I'm still getting this Code! The truck idles rough and serge's sometimes, also there is a lack of power and some shaking between 40 and 50 miles per hour, however form 50 to 60 MPH seem's to be just fine. I don't trust the "Mechanic Shops" around here and will only take the truck in as a last resort.
Ford 7.3L Power Stroke (1999-2003) :: IDM Failure Code And High Side Open Bank 1 And 2
Today I just installed a brand new IDM and after running the Injector Buzz Test test, I received codes: P1298 Injector Drive Module Failure, P1293 Injector High Side Open - Bank 1, and P1294 Injector High Side Open - Bank 2. How a new IDM could throw these codes?
When running the KOEO test I received codes P0605 Injector Control Module Read Only Memory (ROM) Error, P1298, P1293, & P1294.
My engine is still missing but the engine is running a heck of a lot better after replacing the IDM and injector 8 has a rotational velocity of about 3%
Ford 7.3L Power Stroke (1999-2003) :: Code P1271 - #1 Injector High - Low Side Open
Getting DTC Code P1271 - #1 Injector High -> Low Side Open.
The code tends to show up more during cold weather start up. Using AE-AutoEngenuity KOEO - Buzz Test returns the P1271 error
Troubleshooting performed:
- 42-Pin Connector @ Driver Side Valve Cover
- 9-pin VCH on Passenger side
- IDM Module under driver side wheel well
- All of these are testing within the 2.8 - 3.2 Ohm range
- (Used the GB Reman. Tech Bulletin 103) - TB 103: 1994-03 Ford 7.3L IDM Replacement & Diagnostics)
I was going to replace the solenoid, however, with the above readings I'm not convinced it's the solenoid. Before I tear into the valve covers I was looking for some add'l thoughts from the forum. Could it be the IDM ?....
Any add'l checks to perform using AE, or the IDM, other than replacing IDM.
01 Platinum 7.3 - BTS - PHP Hydra Tunes - 4" FloPro - Riff RaffWheel - Redhead Steering - Driven Diesel Hutch/Harpoon - Kenwood DVD w/ back up- 35"s - GloPro EGT/Pyro/Boost/Trans, Scan Gauge II, AE bundle
Ford 7.3L Power Stroke (1999-2003) :: Air Intake Relay Bad?
While doing a visual inspection I noticed that the AIH hot wire (captured nut wire) had broken off and was laying loose. I removed the wire from the relay and made a new 8 gauge wire, I connected it to the relay and was about to add it to the AIH when I got a healthy spark ( it touched the ground wire ) and yes the truck was not running and the key was out at the time.
This sounds to me like the relay has gone south, am I right??? I have a new OEM relay to install but I have a question. In what order are the wires and ceramic fitting go on the AIH post???
Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 - At Signal In Gear Surged - ICP Volts?
03 f350 srw. Today and a few times in the last couple weeks when sitting at a light with truck in gear it has surged a little bit. Not hard enough to make me push the brake pedal harder but noticeable climb and then fall of a couple hundred rpms. I remember hearing or reading of somebody else with the same issue and it ended up being a bad ICP. Checked it koeo when I got home and it was at .35 volts(scan gauge II). I don't recall the right number but that seems higher then what I remember it should be. What else other then pulling the plug and checking for oil should I be looking at? I replaced #5 and #6 injectors about a month ago, and everything seems to be good with that. I don't think the two are related but I'm no expert.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P1393 - Glow Plugs On Driver Side Are Not Working
I am having a difficult time trying to track down the root cause of a P1393 code in a 99.5 7.3. The code means all the glow plugs on the driver's side are not working. I don't have any other codes related to the glow plug system present in my computer.
I've replaced:
1)The Glow Plug Relay (I have the CA version with the shunt)
2)Valve cover gaskets and wire harnesses
3)Glow plugs
I've used all OEM product replacements.
Additional testing:
1)Voltage on the glow plug relay posts going to the left and right bank is the same (I think this means the shunt is okay)
2)Disconnecting the wire harness to the valve covers yields 12 volts at all 8 glow plug connections during the glow plug cycle
3)In one of the steps of a troubleshooting document I found, it requires a KOEO On-Demand Self Test. It does not complete and ends with a P0605 code, "Internal CTRL Module ROM Error" using a Snap On Scan tool.
4)Using the Snap On scan tool to run a glow plug test results in "Test has aborted 64 - Abnormal Exit without result".
5)I checked part of the wiring loom and it seemed to be good.
Is there a way to test the wire that goes from the Glow Plug Relay on the driver-side bank to the PCM? I think that either this wire is bad, or a bad PCM.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Oil Coming Out Of Sensor On Top Of Engine On Driver Side
I have a sensor on the top of the engine on the driver side that has oil coming out of it. I think it is called an IPC but I want to make sure before I go buy a new one. It sits right behind the power Steering pump. I am replacing the Power steering pump and hoses so I thought I would replace that as well. Also since there is oil in the connection what is the best way to clean the connection electric parts cleaner? By the way this is a 2000 7.3 4x4 ....
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Relay For Fuel Pump Keeps Going Bad
The relay for the fuel pump keeps going bad. Is this a sign my fuel pump is going ? I just replaced my 2nd relay ( lasted about 1 week ) 1st lasted 16 years. Or is there another issue to look at ?
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Truck Missing And White Smoke Coming Out - Code P1316
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Blinkers Not Working - Location Of Relay
I have searched everywhere for the location of the blinker relay on my 02 F-250 7.3 and getting mixed results and still not found.
View 14 Replies