Ford 6.7L Power Stroke Diesel :: 2011 - High / Low Beam And Fog Lights Won't Working?
2011 f350 king ranch... I have DRL, turn signals and tail lights. I have checked all fuses ( don't know if there's a relay) under hood and in cab. Still do not have any headlights, high or low beam nor do I have any fog Lights.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Wire For Headlight High Beam?
I'm hooking up some Ridgid driving lights and want to tap into the high beam headlight power wire to activate the relay. Which wire is for the High beams on a 2006 F250 Diesel??
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Power Steering Pump Replacement
When replacing the power steering pump on my 2006 should I go OEM on the pump or save some money and get a Napa or aftermarket remaned unit with the pulley installed? Also, whar is the fluid capacity of the power steering system?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Pan Looks Rusty - Replacement
269k on a 04 6.0, in the rust belt, oil pan is needing replaced according to the tech. It looks rusty for sure. 1300+ to change it. I understand you have to lift the engine some to replace. Engine is stock, are there any aftermarket pan's worth looking at if I'm going to replace it?
View 7 RepliesFord 6.0L Power Stroke Diesel :: Filling Up Oil Cooler After Replacement
Is there a way to fill up the reservoir for hpop and cooler after replacement? I didn't want to burn down the starter and kill batteries cranking all day until everything is full. I did the usual upgrades on the motor and about ready to try and get it started up. Where does the oil drain to when filter is removed?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Head Gasket Replacement?
So, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 RepliesFord 6.7L Power Stroke Diesel :: Filter Replacement Without Draining Oil
Can I replace my n/g oil filter that is defective w/o draining oil? I did oil change and filter is leaking, bad gasket. If I remove oil filter will it only drain what is in filter or entire engine?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Fuel Injector Replacement
My 2005 F-250 does not have power when the engine is cold. When the engine warms up then it seems fine. I believe that the fuel injectors need replacement. I was told that one cannot get new injectors. They are all re-manufactured. Is this correct?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Locking Fuel Cap Replacement?
With how touchy our diesel fuel system is to any contaminates...what locking cap will replace the OEM fuel cap? Also, looking for a locking DEF cap? Looking for caps for a 2016.
View 13 RepliesFord 6.0L Power Stroke Diesel :: Fuel Injector 8 Replacement
I may have to replace fuel injector #8 on my 2004 6.0. Aside from doing brakes and rotors, I don't have any experience working on my truck.
Side note- this is the second injector to go bad in the past few months. Ford also wanted to replace the HFCM, so I'll be doing that as well.
Ford 6.0L Power Stroke Diesel :: No Boost After Oil Cooler Replacement
Got everything done today. So I thought. Went for a drive. turbo not building boost. I checked the map hose and barb. Clean. Checked connection at ebp and vct, both plugged in. No exhaust leaks. turbo shafts feels good and spins good. made boost fine before repairs. 2006 6.0 f250 .....
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Backflush Before Replacement
2004 6.0 90k miles... Oil cooler plugged & coolant puking due to egr cooler flash boil.
Flushed the coolant with tap water then replaced water pump and tstat weekend before. This week backflushed heater core & block. This weekend backflushed the oil cooler. My coolant system would be considered severe contamination due to tap water use resulting in rust. Average ect was 195-205 & avg eot was 230-240 before flush. Here's a baseline before flush.
Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac. The pressure was pretty intense holding the hose into the bore just running water through it. Hit the trigger about 20 cycles of water then air blasts.
Filled with 1/2 gal of restore & tap water. Ran it for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Then dumped restore while hot, was pretty cloudy but not that dirty. Let engine cool then filled with tap water, ran for 10 mins then dumped again. Stuck hose in degas with only the the drivers block plug pulled & revved engine a few times to have the water pump push any crap out. Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac again. This time the back pressure on oil cooler was much less vs first time.
Took a mason jar with restore plus in it & boiled it in water. Got it up to 190 then poured it directly into the oil cooler & let it sit for 30 minutes. Then backflushed again.
Put rest of the whole gallon of restore plus in & topped off with tap water. Ran again for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Dumped restore plus while hot & it was very green & contaminated with rust. Topped off with tap water, ran for 10 mins at 190 then dumped. Revved the engine again with hose in the degas bottle & only drivers block plug out to blow more junk out. Filled with tap water & dumped again.
It was late last night so I filled it with distilled & parked it. Plan to do 3 straight distilled water flushes this week running rpm 1k+ for 1 hour each time in hopes to rid all the chemicals.
The backflush didn't result in lower deltas, but it didn't puke from the degas bottle at all during both chemical flushes. The oil cooler definitely needs replaced but at least it's not puking anymore & will hopefully stay this way for about 1k miles of driving so I can let the coolant filter rid anything that breaks loose during driving. My hope was to get some sort of flow across the egr cooler to stop the flash boiling puking & get as much junk out of the system as possible. So I guess there's some sort of achievement in the end.
Currently running cheap regular green (mixes with all) elc. I am running the cheap stuff because when the coolant was puking a gallon of coolant every trip i couldn't justify upgrading to the Rotella ELC yet. Plan is to flush with rest of restore(1/2 gallon) after oil cooler r&r then switch to Rotella ELC.
Ford 6.0L Power Stroke Diesel :: 2006 - EGR Valve Replacement?
From what I understand it should be dry where the valve goes. I would call it moist not wet but fairly moist. The top groove had the most wetness, the middle groove was dry and the bottom was nearly dry. Where do I go from here - the video I watched said to scrape out and vacuum - not dry enough.
[URL]
Ford 6.0L Power Stroke Diesel :: Bed Bounces While Driving - Replacement?
The cross members on my bed are toast. The whole bed bounces as I drive down the road. I know the cross members can be put in. I'm also considering a whole new bed. I keep hearing about these companies that pull the beds off new trucks to install custom aftermarket bodies, then sell the bed.
View 11 RepliesFord 6.0L Power Stroke Diesel :: Glow Plug Replacement?
I have to replace the #6 glow plug. I confirmed it is bad and the harnes broke when trying to reove it with the proper tool. I ordered a new glow plug, ZD13, and a new drivers side harness.
I have never replaced a glow plug before but it seems pretty straight forward. I watched some youtube videos and did some reading.
I have read some state that you have to loosen the glow plug with a 10mm socket and then take some tubing and push it onto the glow plug to finish loosening it and prevent it from falling into the cylinder. I have read people saying it took them hours with a magnet to get the plug out of the cylinder.
If the plug is threaded and is removed from the threads how is it possible for it to fall past the threads into the cylinder?
Anything special I need to know? Anti-seize on the threads and dielectric grease on the connection? What the torque spec is?
Ford 6.0L Power Stroke Diesel :: Burning Oil After Turbo Replacement
On Friday my turn shaft broke, 70 mph on the highway. As soon as it broke burned oil like a freight train, I know seal in the turbo. Bought brand new Garrett turbo installed last night. Let idle for 5 minuets and went and drove it and it burns oil once I get on it. Drove it for about 3 miles comes and goes? I did break a piece of the turbo vane off 1/4 inch by 1/4. The truck runs fine no knocks or misses. Could this just be oil left over or is there something else I should be looking for?
View 2 RepliesFord 6.0L Power Stroke Diesel :: EGR Cooler Hose Replacement
My orange one leaks, bought a blue one. How the heck to I install it? I have decent tools.
I reviewed the threads on coolant flush and fill, and bought a coolant filter kit, I will be doing that at the same time.
Ford 6.0L Power Stroke Diesel :: Oil Leaking - Cam Sensor Replacement
What is the best way to change the cam sensor on these engines? I believe mine is leaking oil based on some general wetness below it and oil dripping off of the bell housing but I can't find an angle where I can see it clearly let alone replace it. Have to remove the power steering pump?
View 3 RepliesFord 6.7L Power Stroke Diesel :: Side Marker Bulb Replacement
2012 King Ranch, Side marker lights on the side view mirrors. How do we remove it or gain access to bulbs!
View 7 Replies