Ford 6.0L Power Stroke Diesel :: Rear Heater Not Working
I have tried the dealership 3 times and have not been able to get the rear heater to work properly. When the vehicle is moving I have heat but if I slow or stop the heat goes away. I believe it only happens to the rear heater as front feels fine.
View 4 RepliesFord 6.7L Power Stroke Diesel :: 2016 - Block Heater Not Working
I didn't have time to trouble shoot but heres my problem. I plugged my 2016 6.7L in last night and when I checked it this morning the block was still ice cold. I didn't have time to investigate but i did make sure i had power up to the truck. And i noticed there's a connector just after the truck plug as well.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Block Heater Won't Working?
I don't think that my block heater is working correctly if not at all.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Heater Hose Installation?
Had a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
Ford 7.3L Power Stroke (1999-2003) :: Won't Start - Block Heater Won't Working?
I can't get my truck to start. The block heater isn't working and I previously put flush and water in it, intending to drive it and flush it directly after. Well I never really could drive it and now it won't start again. The weather is going to turn off cold, around zero this weekend. I need to know how to keep the block from freezing and cracking!
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Heater Air Blowing Only On Defrost
Have 06 super duty . Heater air blowing only on defrost. 4wheel drive. Is this a vacuum problem or some type of sensor or control problem?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Intermittent Knocking Sound While A/C Or Heater On?
My ford f250 i have a intermittent knocking sound when i turn the ac/ heater? it is not all the time and can never tell when it is going to happen. i always think the worse like it is a cylinder or something.
View 9 RepliesFord 6.7L Power Stroke Diesel :: Block Heater Comes With Cord - Cannot Find One?
Does the block heater come with some kind of a cord? I found the Box Link stuff under the back seat finally, the dealer said the block heater should be under there too? But it aint there?
View 6 RepliesFord 6.7L Power Stroke Diesel :: Adding Supplemental Heater - Wiring Harness?
As it turns out my entire dash needs to come out to repair the HVAC so thinking while it's out I should add the diesel supplemental heater. What's involved with this? I need to replace the entire HVAC plenum so imagine the version with the supplemental heater can be bought instead. I know it's an 1800W electrical heater so my main question is the wiring harness on a regular truck setup for it or do I need to change the harness. And then I suspect the HVAC control module would need to be reprogrammed as well.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Smell Of Fuel When Heater Is Turned On?
I'm hoping it's a small simple fix when I climb under the hood. Has happened before, but was an easy fix. The smell is much stronger this time. Any major problems any of you have had if I can't find the culprit?? Learning as I go...always up for checking on every possibility.
2004 F250 SUPER DUTY 6.0 ......
Ford 6.0L Power Stroke Diesel :: Hard Start When Cold - Block Heater?
Don't drive the truck but once a week but since its gotten colder here than usual is been harder to start when cold. Of-course I go thru the glow plug wait and then it kinda stumbles when its about to start. I do it again and most of the time is starts but seems rough for a few seconds. Once the truck is warm, no more problems starting.
I'm wondering if I have a glow plug gone bad and that cylinder is not warming up for me. Today I plugged in the block heater for maybe 2 hours and it started first time. Also, if just leave the block heater plugged in for long periods of time.. would it get to hot?? and wonder how expensive that is, most heater are costly to run. I have a timer but just wondering.
Ford 6.7L Power Stroke Diesel :: 2016 F350 - Can't Find Block Heater Connection
Well, I swapped a 2011 F250 SC for an F350 CC and I really enjoy driving it. 300 miles on the clock. My old 250 had the block heater and the pigtail to plug it in was low in front of the radiator. This truck also has the block heater, but I cannot find the pigtail to plug it in. In 2016 where Ford hid it at?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Block Heater Plugged In When Starting - Blow A Fuse?
Ok, is it possible to blow a fuze if the block heater is still plugged in when starting? Almost did this the other day and wondered if its possible to cause a short or something.
View 6 RepliesFord 6.0L Power Stroke Diesel :: Coolant Temp After Plugging In The Block Heater Overnight?
What the coolant temp should be around after plugging in the block heater overnight? Not looking for an exact measurement since this can be affected by OAT and the length of time it has been plugged in. But when it's -15 to -20F this weekend I was wondering what to expect.
View 13 RepliesFord 6.7L Power Stroke Diesel :: CEL On For Code P20BA - Reductant Heater A Control Circuit Performance
Okay, so I have a 14' 6.7L, about 18,438 miles on it and the check engine light came on when I was at the gas station ready to leave, and so I took a field trip to auto zone and they scanned the CEL and it came back as P20BA - Reductant Heater 'A' Control Circuit Performance and they said I need to change out the pump assembly so I took it to the dealership and they cleared the code which worked for awhile, about 4 months ago the light came back on and I'm wonder if I should get the pump/heater changed out or get it deleted? The warranty is going to end in august this year..... It's been fine no issues with the truck, even tho I drive with the CEL on and just wondering what I should do? The CEL has been on for almost 5 months.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 - After Start Up Rough Idle And Power Lag?
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Rough Idle - No Power?
I recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Rough Idle And Dies / No Power
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hesitates / Low Power Driving / Idle
I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.