Ford 6.0L Power Stroke Diesel :: 2004 F350 - No Crank But Will Only Start When Jumped Even With New Batteries
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 RepliesFord 6.0L Power Stroke Diesel :: No Start - Replaced Starter And 2 New Batteries?
In the last 2 months I've replaced my starter and 2 new batteries. I've tested the alternator and it's fine. What more is there? I'm guessing the FICM is going to crap. If I attach a scangauge 2 to it now would it tell me if that's the problem?
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2014 F350 - Two Cylinders Misfiring
2014 F350 6.7... The truck has only 30000 miles on it. I was driving uphill and the engine just quit, but fired up right away after with engine check. On idling run at 500-700 rpm , no power, clicking noise , sometimes shaking. Took to the closest dealer right away, they don't know what is it, but they want to rake of the engine . This truck is not under any warranty. This is my first diesel truck, didn't expect anything like this....
View 4 RepliesFord 6.7L Power Stroke Diesel :: 2014 F350 - Axle Gear Change?
I am thinking about changing the Gear Ratio in my 2014 Platinum F350.
History: I traded in my 2011 F350 DRW with 17" wheels and 3:73 gears to get my 2014 F350 SRW 20" Wheels with the 3.55 gears. I pull a 15,000 boat and trailer. The Drw pulled the boat and trailer with no issues. I sold my Northern Lite Truck Camper. I thought I didn't need the Drw any more. First time I hooked up to the boat I felt the difference in between the trucks in the acceleration and fuel economy. Old truck would get 11.5 MPG new truck gets barely 9 MPG going down hill with a tailwind. Over all the new truck is a little slower off the line but when hooked up to the boat it is a dog with the 20" tires.
So the question to you all is; gear change to 4.10? Swapping to this ratio with 20" tires will produce the similar RPM's and possible improve the fuel economy. I get around 18 empty now on trips empty. Around 16 commuting 25 miles to work.
Ford 6.7L Power Stroke Diesel :: 2014 F350 - Grinding Noise And Tire Wear
Ok haven't been on here in a LONG time. Sold my '12 and bought a DRW '14 F350 to tow our fifth wheel. Just got back from a 775 mile round trip pulling our fifth wheel. My dad noticed my passenger front tire was going bald on the outside. I said yeah it was pulling to the right and thought my tire was low but when I checked it was the right psi.
Turning to the left I was starting to get a grinding type noise. If I rolled my passenger window down you could here something just grinding away but when you straightened out nothing.
So I took it into the dealer and they tell me the outside tire wear is normal. I said it has 22,000 miles and the passenger tire will be bald on the outside in 4,000 more miles or less. Said they can't hear any noise, yet my wife can hear it, kids can hear it and people outside the truck can.
It's not normal for the passenger or drivers tire for that matter to go bald in less than 25,000 miles? Tires have always been kept to proper psi, I've towed only about 5,000 miles total with it. They are also taking the worthless rancho rebranded shocks off and going with bilstiens. I should have replaced them 10,000 miles ago. They are horrible shocks.
It really torques me that they have it for a week and can't find anything wrong. When turning to the left it's almost like bump steer in 4wd just not quite as bad but with also a grinding sound that you can hear inside the cab and can feel it in the floor board. Nothing evident but just looking under the truck.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - No Power On Cold Start
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hard / No Start - Low Power
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Lost Power And Won't Start
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
Ford 6.0L Power Stroke Diesel :: 2003 F350 Will Not Start
I have a early build 2003 f350 6.0. It will not start. Readings are good. ficm 48 to 48.5, synced, icp volts .30, icp climbs above 1200 psi, bat 13 to 13.5, ipr 14.8 to 40, fuel pressure 82 psi during crank..... will not start. Last week tore it down and replaced the tube of the hpop, found a leak in map hose and cleaned the turbo (vanes, ring). Ran ok for a week... shut it off and my sons baseball practice and will not start.... towed it back 2 days ago and nothing..... just cranks... I am at a loss. Another question would be where do i air test the hpo system on this truck.... ICP and IPR are in the back of the motor and hard to get to. I have read there is a way to do it under the valve covers.... not sure.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Won't Start?
2005 F 350 6.0
124000 miles. Drove the truck on a long road trip Saturday ran great. Didn't touch it Sunday. Went out Monday morning and it wouldn't start I noticed the fuel gauge said empty and the low fuel light was on. I knew there was plenty of diesel still in the tank but I still went and bought 5 gal and dumped in it fuel gauge then read over half full but still won't start. A buddy who's a mechanic swung by sprayed starter fluid in it fired right up then died he said I need a new fuel pump. I have been reading the forums. I just want to make sure is he right?
Ford 6.0L Power Stroke Diesel :: 2004 F350 - Lack Of Power While Accelerating / Stall And No Start
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Batteries Going Dead Overnight
My batteries go dead over night, had them checked but they say there good, can't figure out what's causing them to die.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 Will Not Turn Over / No Start
This truck is bone stock FYI. I get in it to crank it and I get nothing. Batteries are good, everything in the cluster lights up, and looks normal. No codes are thrown. I can hear the solenoids click under the dash and hood. I check the voltage of ignition cable at the starter and I get no reading.
There is a single thick yellow with light blue stripe coloured wire on the passenger side of the engine compartment, beside the vacuum pump with a "squeeze and pull" type disconnect. Disconnect it, and connect the male half of the connector to the passenger side battery positive terminal. Do this with the ignition key in the RUN position. Does the truck start?
This is where it gets weird. The truck does start and after i reconnect the wire it it starts normal. I started it several times throughout the day. The next morning I get in the truck. No start. I have to use the wire and manually connect it to the battery and it starts right up again. This time I get a "Tow/Haul" light blinking on the dash. It will go into gear but pressing the acceleration pedal does nothing. I turn it back off, attempt to start it normally and it starts right up. No it will go into gear and drive. Now I am thinking maybe the neutral safety switch?
Could it be a solenoid sticking or the neutral safety switch or something else entirely?
Ford 6.0L Power Stroke Diesel :: 2004 F350 Truck Will Not Start
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
Ford 6.0L Power Stroke Diesel :: 2004 F350 Crank But No Start
I have a 2004 f350 6.0 powerstroke i recently fixed a oil leak in my remote oil cooler and after I was finished it ran fine and ran fine for a few days I noticed yesterday it had a bit of a rough start and some today but would start and run normal. Started the truck this morning and drove it a bit and then let it sit while I went to the dentist came back out and truck wouldn't start. I am getting 200-330 icp with the ipr cycle at 88.5 ficm sync is good and colts are at 12.5 unplugged icp sensor to see if it would start after that and it disnt start so I ruled that out.
I'm currently waiting on AAA to bring my truck home for me but trying to make sure I'm right to start working on it tomorrow. I am thinking the ipr valve is clogged. Am I right to think this may be the issue? When I first installed my remote oil cooler I had the same issue crank no start turned out to be the ipr valve was gunked up and I ended up replacing it 300 dollars later. Then it started and everything was fine. So basically am I right to start at the ipr valve or should I start somewhere else?
Ford 6.0L Power Stroke Diesel :: 2003 F350 DRW Won't Start - Not Getting Enough Fuel?
ICP and IRP changed both fuel filtrs and Blue spring put in. HPOP Pressure is over 1600PSI when cranking with 2.5 to 4 volts.
Will try to run but acts like not getting enough fuel. If I loosen the lines off the upper filter housing lots of fuel runs out. Lots of smoke when cranking also.
FICM volts are 48.5.
Reading with Scan Gauge 2.
The truck is a 2003 F350 DRW Stock 6.0 with 433000 on the odometer.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - No Start / Cut Off While Driving
My friend has an 05 6.0. He's having a no start issue. He was driving and it cut off, he couldn't remember if it cut off quick or sputtered. I hooked up my AE and jumper cables and stated looking. Cranking the icp would only build up to 190ish. I unplugged the icp sensor and AE was reading 1538ish??, I guess that was a default value. The ipr reading immediately went up to 85% but still doesn't fire. Also while cranking there wasn't any white smoke at all from the exhaust. A few years ago he broke down and Ford put in the updated snap to connect fitting. He said they also replaced the dummy plugs but he didn't mention stand pipes so... I'm not where the truck is so if there's any questions it might take a few.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Just Died Now Won't Start
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Won't Start When Warm
I have a 03 350 with a 6.0 . The truck starts fine in the morning and runs great all day as long as you don't shut it off. It's not going to start until the morning. It will crank over fine, the fuel pump seems to be working, its like there is no power to the injectors. I don't have a wiring diagram so not sure which relays are for injectors. Could the ficm be causing it? Is there a site where I can download a fuel sys schematic ?
View 4 Replies