Ford 6.0L Power Stroke Diesel :: Gage Fault And Tow Haul Flashing On Dash?
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 RepliesFord 6.7L Power Stroke Diesel :: Exhaust Fluid Fault Code?
Just wondering what this could be.its giving me the 50 miles to 50mph max speed. Def tank is half full.truck runs fine.
View 2 RepliesFord 6.7L Power Stroke Diesel :: Code P246E - Exhaust System Fault
I had a ford technician plug in and check my CEL. Says P246E, Bank 1 sensor 4, exhaust system fault. I am leaving for holidays in a couple of days but dealer to busy before I leave. Is this something that will leave a guy stranded on the side of the road? I've already been towed once...
View 5 RepliesFord 6.7L Power Stroke Diesel :: 2012 F250 - TPMS Fault Code
I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2013 - CEL On With P206 Code / Fault Inj 6 Open Circuit?
On a family vacation in our 2013 6.7 pulling a 41ft trailer to the Seattle area from Alberta Canada. Made it to destination yesterday. Woke up this morning started truck and cel on. Bought a code reader at the local napa store and read P206 fault inj 6 open circuit. Any thoughts on driving the truck around with a inj fault? Thought I had read here some where that 6 was the regen cylinder.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Fuel Gauge Inaccurate / Fault Code PO191 - Hesitation When Accelerating
My fuel gauge on my Sport Trac is nowhere near accurate. Ran out of gas the other day showing 1/4 tank.
I get a little hesitation as well when accelerating.
I'm showing a PO191 fault code which says Fuel rail sensor.
Would that cause a gauge to malfunction?
Ford 6.7L Power Stroke Diesel :: Power Door Lock Fuse Blowing Occasionally?
I purchased 2011 F250 King Ranch Edition about 3 months ago. I'm loving the truck and not had any issues until 3 weeks ago. I locked the truck as usual using the key Fob, and upon returning to the truck, I noticed the doors weren't locked. After some brief trouble shooting, I discovered the the fuse was blown that according to the manual controls just the power door locks. I thought it was strange that a new truck would be popping a fuse so I replaced it...a couple of days later it blew again. This time I was locking the truck with the door key pad. I took it to the dealership and they checked it over and said they replaced the fuse and cycled it numerous times but could not reproduce the problem. The told me that they even put a call in to the Ford engineers and they said check the key pad for water intrusion. The dealership told me they disassembled the key pad and found nothing wrong....lock and unlocked the door some more and the fuse would not blow. I picked the truck up four days ago and the fuse blew again last night. Everything else works...alarm sets and goes off if any of the doors are opened. The only thing that I can find that doesn't work when the fuse is blown is the remote start.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Wiring Fault On Trailer
Hooked up the toyhauler Friday and before we were off of our street I got the "Wiring Fault on Trailer", brakes on trailer worked, got out and verified the lights were working so we proceeded on.
When we got to the destination the manual says that if the fault stays on when disconnected it is an issue on the truck side, it is still on when the trailer is disconnected.
Ford 6.0L Power Stroke Diesel :: FICM Has Been Dropping To 44v Occasionally
My ficm has been dropping to 44v occasionally so I have ordered a 270a alternator from Ed at ficm repair along with the complete battery cable kit. I also took ends advice and bought two new odyssey 65 series batteries. I went with bpd 6phase ficm though because I like the idea of the extra phases to share the load and back up the 4 primaries. I am also doing the blue spring upgrade while under the hood as well.
So my question is this.... My truck is bone stock no mod 53k mi. The bpd ficm can be set to 48,53 or 58 v. I do not see the need to do 58v but have seen a lot of guys doing the 53v option. What is the advantage of 53v? I know if you run 220 thru a 120v light bulb it will burn bright as hell for a little bit till it blows, is this the case with running a higher voltage ficm? Will it eventually wipe out injectors? Or even the ficm processor board? Should I just stay at 48v setting?
Ford 6.7L Power Stroke Diesel :: Trailer Brake Control Fault
It just came on when I ran up to the gas station followed by the airbag light and the traction control light.. truck ran fine. I've tried looking this up found some people have had this message and there truck won't start.
View 6 RepliesFord 6.7L Power Stroke Diesel :: CEL And Exhaust Fluid System Fault Came On
My check engine light just came on and a few miles later the "exhaust fluid system fault" also came on. I plugged in my scanner and these codes came up:
P2479 b1s2
P2033 b1s2
P050E
P0231 b1s2
I'm assuming these mean bank one sensor 2 is bad. Need to verify? I don't remember all these codes when the #4 sensor went bad.
Ford 6.7L Power Stroke Diesel :: Trailer Wiring Fault - Only When Backing Up
I only get the fault when backing up. Driving forward it's never a problem. The truck is a 2015 F250. We are pulling a 33' travel trailer. Both are new. I was not sure if the fault when backing was something that happens or if it might be indicative of a problem. The manual says it's not an indicator of a problem. Rather, there might be an issue. Again, it works fine when traveling in a forward motion.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Tire Pressure Monitor Fault On Display
Well, at a little over 10k I have my first issue. My monitor displayed a Tire Pressure Monitor Fault. All tires are OK. Light won't go out. Guess it just earned a trip to the dealer.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Exhaust Fluid Fault With P20EE AND P2080
Set out for a 450 mile trip this morning. Checked all fluids, then checked the Edge CTS for any DTC's since it had been several weeks since I had driven the truck more than 100 miles per day. No codes except for a couple of P0000's.
Good to go.
45 miles into the trip while traveling at 75 MPH the chime sounds and the message center says "Diesel exhaust fluid fault. Speed will be reduced to 50 MPH in 50 miles." CEL on too. Using the CTS, I checked the codes:
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
P2080 - Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
They were in the order shown. So the EGT fault came first, followed by the NOx fault.
I really need this truck today. Cleared the codes, but of course that didn't work with the 50 MPH limiting. Went back home and got the Jeep. The truck is about 1 mile away from the 50 MPH speed limiting.
It would seem that the EGT problem could lead to a NOx issue, but I could be wrong. I monitor EGT1 with the CTS, but I didn't see anything out of the ordinary. Also I thought an EGT fault usually gives the "Stop safely now" fault.
I did take a picture of the CTS DTC display before clearing the codes. Hope that will work for the dealer.
Ford 6.7L Power Stroke Diesel :: 2014 F250 - Clunking Trans And TPS Fault
I just bought a new 2014 f250.
He says since he has purchased the truck the TPS sensor would occasionally go off saying there is issues with the tires. Tires are fine yet the light chimes on after being reset shortly. Been at the dealer for a week and they haven't really touched it I was wondering if there is any know issues.
Also my dad had the truck in 4x4 and when he puts the truck in park it made it a loud clunking noise. Ford is said there heavy duty line was full so they didn't look at that ethier. He needs the truck for the weekend so he is picking it up tomorrow, he will return it when he can but does this sound familiar as well?
Ford 6.0L Power Stroke Diesel :: Extreme Lag In Acceleration / Occasionally Doesn't Want To Start
I am noticing a extreme lag in acceleration. When taking off from a stop it lags really bad then acts like I floored it. My FMP is 48 sometimes dropping to 47.5. FLP is 13 sometimes dropping to 11.5 during starting. Occasionally it doesn't want to start, like its not getting fuel. New batteries 3 months ago. Also has blue spring. Its a 2005 thats never had anything done to the FICM, so its kind of old to begin with. I read in another thread that the FICM relay should be replaced occasionally, so may that could be contributing to some of my probs.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Roll X Installed Now One Corner Unlatched Occasionally?
I installed the Roll X on my truck on the 27th of June. On several occasions I have found one corner has come unlatched. I'm not sure if it is from the bed flexing when I go over a bump or what?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord 6.7L Power Stroke Diesel :: Trailer Brake Module Fault Message On Display
Brought my truck (2012 F350) for recall service for one of the faulty exhaust temperature sensors. It took them one week to replace the sensor (!), then when I came to pick it up I got: "Trailer Brake Module Fault" message on the display.
I have never seen this message, since I own the truck (I am original owner). The service adviser said it will take a minute to reprogram the module and took the truck back to the shop. Came back after a while, saying that it didn't work and I need to leave the truck, so another technician can work on it tomorrow. Tomorrow came and I got the call that they reprogrammed the module, but the message still shows up, so they need to work on it (another day!).
As of now they still don't know what is going on. Apparently they broke something while replacing the EGT sensor and how to fix it.