Ford 6.0L Power Stroke Diesel :: Randomly Shut Off When Pulling Into The Driveway - P0341 Code
A Little Background, my FICM wasn't bad per se but it would dip below 45 volts when the outside temp was around freezing. I pulled it and sent it for repair at the same time the Atlas 40 tune was loaded into the FICM.
First few days of driving mileage was better, truck ran great. All of a sudden one day pulling into the driveway it randomly shutoff. Two occasions since it has acted goofy at started, bucking a little a low throttle. Mileage has returned to how it was before I had the FICM fixed and ATLAS tune applied. To this point I had no codes at all.
Now today it randomly throws P0341 - Camshaft sensor out of range.
So heres the question - do I replace the sensor or try to get at the harness for inspection? Out of range would usually mean the sensor itself is failing while open circuit is usually wiring related. I know its uncommon for this particular sensor to fail but i'm not sure which direction to go.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Randomly Dies Will Not Restart
Ok, so my 2002 f250 died on me last Tuesday out of the blue, pulled it home and found fuse 23 I think ECU power was blown. I removed my Hydra, and put a new fuse in it and all seemed well, then Friday evening on my way to dinner was driving along and truck shuts off like someone turned the key off. I replace the Crank sensor, even though I had put a new one in after the first time it died, which was last Tuesday, still would not start.
Pulled it home, went out Saturday morning to look at it and hit the key and it fired right off. At this point I don't really know where to look, I wiggled every wire I could find while it was running Saturday and no change, but it does seem to have a miss in it while it is idling...... I am not sure where to start looking....
Ford 7.3L Power Stroke (1999-2003) :: Truck Misses And Randomly Dies Only When It Rains
I am at a loss on what this could be. For the past 8 - 9 months my truck will randomly miss and if I am going slow enough it will cause the engine to quit but only when it is raining. I sometimes get a service light when it happens but as soon as i turn the key off and back on it goes away. My truck runs perfect otherwise and even when it rains except when it randomly does what I just explained.
This started when I replaced my passenger side valve cover gasket and I also took out my "brain box" (don't remember what it's called) and put it back in (didn't replace it). I did have the up-pipe replaced as well around the same time and put in EGT, boost and trans temp gauges. That's about the only things engine compartment wise that's been done.
I did just take it to a shop to put on a scanner and after his testing it did spit out 1 code. It was the cam position sensor. Can this sensor cause what I have explained? Like I said, this only happens when it rains. Doesn't matter if it's poring or barely sprinkling.
Ford 7.3L Power Stroke (1999-2003) :: Truck Just Dies Like Shut The Key Off When Warm
I have a 99 7.3, I took off driving the other day and after about 10 minutes the truck just dies like I shut the key off but everything was still on. I tried to restart it and it would fire for just a sec then die. I set for about 15 minutes and tried again it fired up and ran about 5 mins then the same thing. I had a buddy hook it up to his scanner and it has a p0605 and another icp code.. We changed the icp then erased the codes.. Ran some rest through the scan took with the truck running and no codes so we took it for a drive made it about 20 minutes away and same thing but this time has the p0605 code again. Could the pcm be bad? I also noticed the electric pump is always on all the time it will cycle at least 30 seconds every time the key is turned??
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts Then Dies - Shut Down While Driving
My truck is an 02 F250 7.3 with 280,000+ miles on it, so I wouldn't be surprised if I might have a number of things going wrong. It runs pretty good, but is still far from 100%, at least up to my standards. So the problem has been going on for the last two or three weeks and got worse today, and there were a few things leading up to it as well. I'll start off with the first thing that happened that I think might be related. It was about 6 months ago, my buddy and I were putting my new headlights in.
It was parked in his garage and we backed it out a little bit to try and adjust them. It was sitting there idling for a minute or two and just shut off or almost stalled out. Tried to restart it and it wouldn't start, tried multiple times to no avail. It acted similar to when I had glow plug troubles when I first got the truck, it would just crank and crank, but never actually kick over and start, along with putting white smoke out the exhaust. Ended up waiting about a half hour and then the truck fired right up with no problems after that, so I didn't think much of it.
Then fast forward to last week to when something similar happened. Started it up after sitting for a few days, started right up, idled for a few seconds and then just shut off. Started it back up ran for a second and died again. Tried a third time with the same result. Fourth time fired right up again and stayed running, let it run for a few minutes and was fine. Also along with this, there was a bad squeaking coming from the front of the truck, like what a belt would sound like. I have recently replaced the belt because it was squeaking and actually got chewed up and almost shredded completely apart.
So not sure why it is squeaking again, but not sure if this could be related or not. Then took it back to my dorm room to get my stuff, and then made it the hour or so drive home from school, without issue. Even went to a few stores before I went home, and shut the truck off and started it back up multiple times, again with no issues. When I drove back earlier this week it was fine until I got there and put it in park. It idled for few seconds and then cut out for a second, but then idled back up and continued to run fine. It has done that a few times as well. So it will do it on a cold start or after already fully warmed up.
Then it got worse today. Again had trouble starting it cold, same as what I explained early. Except second time cranking it wouldn't start at all, then on the third crank it started up and stayed running. But on the drive home is when it got worse. About 5 or 10 minutes into my drive, was just cruising doing at about 45 or 50, and truck just shut off, died/stalled out. It cut out and shut off for a second or two and then started itself back up and continued on like nothing happened. It scared the crap out of me the first time it happened, I was waiting for something like that to happen, but still wasn't quite ready for it.
The truck acted just like it would before you start it, with the key on, dash lights worked and the radio still worked. It did this 4 more times in similar ways, would die and then start back up, at various speeds and at roughly 5 or so minute intervals. I decided to just keep going as long as the truck would start and stay running, hoping to make it home. It did it a fifth time and this time the truck completely shut off and wouldn't restart itself. It was hard to see, as I was watching a few different things at one time, but I think it tried to restart, I noticed the tach bounce between 200-400 RPMS and then die. So I had to pull over and then restart it, fired up and drove fine. That was about half way home, and I made it the rest of the way home without any more problems.
So obviously I'm wondering what would be causing the truck to do this? I've done some reading and have a couple ideas, but not really for sure on anything. I was thinking maybe the CPS, I think it can cause a no start issue. Could ICP or the ICP sensor have something to do with it? I was also thinking maybe something fuel related, such as fuel pressure or a bad fuel pump. Any of those sound to be on the right track?
I have the torque pro app, but not exactly sure how to use it yet, and also just got access to my Uncle's Snap-on scanner, so I ran some tests and pulled some codes. How to more utilize these tools in diagnostics. I did get a few codes, but I'm not exactly sure how they might be related. The codes are pulled are:
P0470 Exhaust Pressure Sensor Circuit Fault. Just cleaned that out as well as the tube about a year ago, but I guess could be clogged again or has gone bad.
P1274 Cylinder 4 (E) High to Low Side Open. Did some reading and figured out that this could be UVCH related. At the same time, about a year ago, did new injector O-rings as well as all new Motorcraft UVCH's, so can't imagine that one is bad. Or that one could be loose, I would have guessed it would have happened more when I first did them, not a year later, but who knows.
Also pulled P1876 T-Case 2wd Solenoid Circuit Fault. Not sure if this is related at all, but also not sure what it means either. I read that it could be ESOF system related, which I do have, but I have manual lockout hubs, so maybe that's why it throws the code.
Also a few things that may or may not be related, but I think worth noting. Ever since I've had the truck the check engine light will pop on and off sometimes. It will do it on a cold start or, when I first start driving and its not fully warmed up yet. It does it most when the engine is still cold, and it almost never comes on once the truck is fully warmed up, but has came on and off more frequently lately. When driving, it will only stay on for a few seconds and more often when I'm lugging the engine or at lower rpms, and will commonly shut off if I let off the throttle.
I don't think it really comes on at higher rpms. I also have a slight oil leak in the valley of the engine, seems to maybe be coming from the front of the motor. Nothing too serious, leaves a small puddle where I park, loses enough to be at the add mark, a little before an oil change. Changed the oil about 1500 miles ago and have been able to notice a slight drop in oil level. Also I have changed the fuel filter in the last 500 miles.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Rough Idle And Dies / No Power
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2007 - No Power / Dies Once Up To Temp But Restarts Fine
I have an 07 6.0 diesel and I'm having trouble once it gets hot. It begins to lose throttle response and shakes while cruising and also has a rough idle. sometimes it dies while idling but after cooling off for a few minutes starts back up and runs fine. I've checked the high pressure oil and the ficm and both of those are fine. I've done an EGR delete so it has nothing to do with that either. My MPG also goes way down when this happens.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2007 F350 - Power Loss After 10 Miles And Dies But Will Restart?
I have a 2007 F350 6.0 Diesel. Truck starts and runs great for about 10 miles and then loses power and slows down til it dies, it does this without any kind of warning and does not rattle or anything. If i let it sit for about 15 min it will start right up and drive fine for another 10 miles or so and do the same thing.
It did the same thing in December but would not restart at all and the ficm was the cause at that time so i went ahead and replaced the ficm just to eliminate it. I also replaced the fuel pump and the ipr and icp valves are good. The only engine code has to do with the fuel level sensor and that has been on for a year. The egr was recently replaced, the hpop is putting out the psi that it is supposed to and there are not any internal air leaks.
Ford 6.0L Power Stroke Diesel :: Dies Intermittently While Running?
Dies while driving down the road and usually will restart with no problems.Seems to happen more often when it gets hot out. IPR/ICP are good.It took a long time to start once also. I'm leaning toward fuel pump but ?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Dies While Driving?
My excursion died while driving down the road I lose everything but once I turn the key off and turn it back on it will start turning over again but don't . I let it set for a few minutes and it will start right back up like nothing every happen . this is our only transportation for now. The recent things I've done is change out the radiator and upper and lower hoses due to a tiny crack in the neck. I also changed out the hose from turbo to pipe on the hot side due to wear out hole.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Cranked For Few Seconds Then Dies?
My truck will only stay cranked a few seconds then dies, I have a lot of codes popping up! I was told may be the FICM.
View 3 RepliesFord 6.7L Power Stroke Diesel :: Randomly Cuts Out When Accelerating
I have a 2013 that randomly stutters or cuts out for a second while accelerating. This happens whether I am slowly accelerating or full throttle. This used to happen once every few months but it is happening more frequently now. It will randomly happen while trying to accelerate on the freeway. The truck feels like it stalls, then takes off. It feels like it loses boost pressure so maybe a wastegate issue or possibly an EGR valve issue. No codes are set.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Motor Was Knocking Tapping - Power Loss Then Just Shut Off
Not sure, it doesn't seem to me the dreaded fuel pump problem. Was driving on highway pulling my 5th wheel after going though the toll both it never went out of 3rd gear and motor started taping pretty bad, turned tow haul off and it shifted up. All along never seemed to lose power, as I was looking to pulled off high way and into A park in lot it started losing power then just shut off. All along this 2min ordeal the motor was knocking/taping. Seems to me like the motor blew.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 6.0 Just Losing Power And Shut Itself Off / Crank But No Start
2003 crank no start, 196k bone stock truck egr still in truck and stock head bolts. Replaced the icp sensor and ipr sensor, both from ford. What happened is I got fuel then about 15 minutes afterwards my truck acted like it was going up a hill and was just losing power and shut itself off. ficm tested 48.5 volts all 8 injectors tested good and there is oil pressure. Had an egr fault code but I'm at a loss.....
View 7 RepliesFord 6.7L Power Stroke Diesel :: DEF Warning Won't Shut Off?
I just got 500 miles to empty message. On my next trip out I grabbed a 2.5 gallon at my local auto parts store. When I had 99.9 percent of the jug in, it actually started to spit back out. I got the rest in and figured I was done. It did seem strange that it only took 2.5 as I figured it was just about empty to get this message and 2.5 would only take me half way. Anyways, a few trips later and the message is still there. Do I have a bad level sensor or was it spitting out prematurely? Shouldn't 2.5 gallons have killed the warning even if it didn't fill it?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Won't Shut Off By Key?
I have a 2005 f350 6.0 and it has a startup kit installed. When I start by using the key works perfect. But won't shut off by key! I have to use the stop button on key fob to kill the engine. I'm thinking relay might be stuck? And the relay on start up kit is working? Key removed it doesn't diesel down, it runs like key is still in.
View 12 RepliesFord 6.0L Power Stroke Diesel :: Shut Down While Driving
Just to give you a run down on my truck. It's a 06 F-350 4x4 supercrew 6.0 with 78,994 miles. The trucks has been studded with Apr and aftermarket head gasket, Powermax turbo with a wicked wheel, RCD EGR delete kit, 5" turbo back MBRP exhaust, Driven Deisel regulated fuel return system, high REV valve spring kit, EBT sensor, 58volt swamps diesel FICM, edge evolution, within the last 4000 miles New oil cooler, crank sensor, cam sensor, IPR valve, ICP, batteries and lift pump. I think I'm missing a couple things but that's the layout.
Now for my problems recently took the truck to Florida from Illinois towing a 8500# boat. Before I left I had the oil cooler changed, Rotella T6 5w40 ,New filters And 2 bottles of REVX. The try k didn't miss a beat on the 1300 miles trek down. It sat for 3 days before coming back up lite truck. I was gonna drive straight thru and with 1100 miles down and 200 to go the truck acted like it was running out of fuel and died at 90mph. Fuel Gage read 1/2 tank to go.
After letting it site a 1/2 hr it finally fired back up and drove 5 miles before doing it again. This went on 3 more times. I even limped it to fill up the tank thinking the gauge was bad. Nope did it again And called for a tow truck. This was in mid october and 20 miles ago. Since then I've replaced fuel filters, lift pump, IPR, ICP, cam and crank sensors, sent the FICM in to have tested, replaced batteries. No the problem is worse. It Now has created a serious miss when it's cold till 90 then it Idles smooth but keeps dying on me like it did when it was towed.
Ford 6.7L Power Stroke Diesel :: EGT Sensor Shut Down
I am award of the problem. And hope to be one of the majority that never has to deal with the issue. But, if the problem were to happen and the code thrown could it be as easy as to pull over. And if you had a code reader that could clear code.
Could you simply clear the code and be on your way? If so, how far would you get before the code reappeared and you had to repeat the read and clear the code again.
Ford 6.0L Power Stroke Diesel :: 2005 F350 Dies While In Gear?
I have a 2005 f350 king ranch,I have a kinda weird problem.the truck starts up and runs great as long as I let it get to normal temp.but if the motor is cold it will idle fine but if I goto put it in gear it just dies.sounds like tc is locking but I don't get any codes.
View 9 Replies