Ford 6.0L Power Stroke Diesel :: Dash / Windows / Locks / Radio All Quit Working
We just replaced an injector in my truck. Everything was fine, ran great, etc.
On the freeway home, the dash, windows, locks, radio all quit working. at first they'd stop and come back, stop and come back, etc. then finally they stopped. As I was getting off the nearest exit, the truck started dying on me. Once I got pulled over out of the way, it acted like the battery was completely dead.
After a few minutes of scratching my head and staring under the hood, I happened to look at the passenger side batter, and the crossover cable from the drivers side was broken off right at the terminal!! We must have broke it off while doing the injector. as I look closer at it, it had been broken before. Some idiot before me had actually taken a broken crimp style terminal, shoved it and crimped it into a new one and called it good.
I was able to redneck it back together so i could finish the last couple miles home. I fixed it properly with a new crimp terminal, heat shrink, etc. Why did the engine die with the crossover connection broken? was it because the series was not complete, and all the electronics were running off the battery(s) and not the alternator? I'm really confused. I've heard of people only running one battery before.
Ford 7.3L Power Stroke (1999-2003) :: Power Windows And Radio Quit Working
On my 2003 powersteering the windows and radio will just quit working. Then they will come on again. Maybe in and hour or a day or a week. Where do I sart.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - No Radio Or Power Windows
I have a 2004 F250. Owned it for a little less than 4 miles (186k on the odometer) .. The other day making a routine run and the radio goes out. Stopped to check it out and found I had no power windows either.
Made it home, checked the fuse on the radio and its good and the the power window fuse is also good. Put a meter on the terminals and have no voltage going to them. What I need to look at???
Ford 6.0L Power Stroke Diesel :: Battery Light On - No Gauge / Radio / Windows - Alternator?
So I have been having this little issue for a few weeks now. I will be driving along and out of nowhere my batt light will come on and my gauge cluster,radio and windows stop working and the ficim volts jump to 15.5-16.5. This is an intermittent issue. Yesterday I put my multi meter on the alternator and I am reading 13.5 or so this number was done at idle and the batt light was NOT on .
View 14 RepliesFord Super Duty (1999-2016) :: 2007 F350 - Power Windows / Radio Quit Working
I just bought a 2007 f350 lariat and my radio, pwr Windows and the 2 lights beside the dome light don't work either... it looks like there was a new relay put in recently.... Is this some kind of wiring problem or where to start looking..or what might be my problem... I am clueless when it comes to wiring .
View 3 RepliesTacoma :: 99 - Truck Radio Quit And Then Power Windows Won't Work
Driving home today the truck's radio quit, then the power windows would not work. Dome light would not come on and truck started running poorly. Over a period of ten miles it went from running normal to creeping along just above idle (1200 rpm or so). Then it quit completely. Did not have enough juice to start. Checked battery voltage ~13volts. About an hour after it quit it started and act like nothing was wrong. What do you all think might have caused this?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Power Windows And Radio Go Out Occasionally?
I now have a 2002, 7.3, 250, 4x4 and love it. Everything but the milege. All in all it's a great ride. I have one little problem that's driven me nuts.
The power windows and the radio go out occasionally. Both at the same time. They come back on...... sometimes. Sometimes it takes a day or two. I've checked the fuses and then saw that there is a breaker in the 601 location in the fuse box that's probably causing the problem.
But I thought that it was supposed to shut off to protect that circuit when there is a short somewhere. I don't know where to go or how to locate the short if in fact this is my problem.
Ford 7.3L Power Stroke (1999-2003) :: 2007 - No Power To Radio / Windows / Dome Light?
My buddy is selling his truck in a couple days and was taking out speakers, afe intake, and satelite radio. I go to start the truck and i have no power to windows, no power to radio and no domelight when i switch it on and off. Dont know what i did but none of this works and everything else does.
I checked all fused all were good. I searched the forum for a solution and they said something about the automatic delay relay and i bought a new one and nothing still. I am not sure what else to do i checked with voltmeter if i had anypower to the window or radio and nothing. But the radios clock works and when i turn on the light it illuminates but doesnt turn on.
The truck is a 2002 7.3L Crewcab. f350
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Radio / Windows Stop Working Occasionally?
I have a 02 PSD, and sometimes after I start it up my radio and power windows do not work. I have a red "security" light on my Kenwood radio that turns on when the truck is off. That light keeps flashing after I turned on the truck so I know it's still getting power, but for some reason it thinks the truck is off, and the windows don't go down. Other days it works perfectly fine, sometimes the radio and windows will stop working after driving normal.
At first it was a routine where I knew they'd start working shortly. But today was the last straw, I drove into work with no radio and windows not rolling down for 30 miles. Of course after I park, I turn off the truck, turn it back on and everything comes on like nothing ever happened. What can be causing this, I have checked all the wiring, no kinks, cuts, nothing. I remember reading something about a relay that can cause this but can't find that info.
Ford 6.7L Power Stroke Diesel :: A/C Quit Working?
I went on a 4oo mile trip the other day and kiddos were in the back playing games and powered up- Next thing I know the AC seems to not be working. It was pretty cool outside so I tested it a little and I could not feel any cool air in the seats and teh vents were not very cold.
Clutch seems to be engaged and not cycling.
I am taking back to them Wednesday.
Ford 6.0L Power Stroke Diesel :: 2006 - 4WD Quit Working
My truck does mostly pavement duty so no telling how long ago 4WD quit working but I needed it the other day and it's now a no-go. It's the '06 truck in my sig and it has ESOF.
When I flip the switch (4hi or 4low acts the same) my A/C continues to come out of the dash vents, it doesn't change. With KOEO I can hear a whirr-click from under the truck when switching 4wd on and off, I get noise both ways. 4x4 light on the dash seem to work correctly.
Broke out FORScan and got the following info:
===GEM DTC P1832===
Code: P1832 - Transmission Transfer Case 4WD Solenoid circuit failure
Module: Generic Electronic Module
Diagnostic Trouble Code details
Transmission Transfer Case 4WD Solenoid circuit failure
===END GEM DTC P1832===
[Code] ....
Any tips to quickly nail it down between the switch, GEM, wiring or solenoid? Looks like the whole thing is failing. I've climbed under the truck and all the wiring appears undisturbed. No recent work under there. In FORScan, these DTC's were generated in a user initiated test and I didn't pick up the instruction to re-run the test in 4x2 mode until I posted just now.
Under the hood everything seems to be routed correctly and connected. Vacuum pump runs a short while on start up like always has. I can lock hubs manually and they don't seem to be binding hard but they are a little stiff, haven't done that before so I don't know how hard it should be to turn them. I have a MiteVac but haven't tried using it to try and lock the hubs. Not sure any of that matters (yet) with the DTC's listed above.
Ford 6.0L Power Stroke Diesel :: Back Seat Power Windows Don't Work
It's my turn, while out site seeing my back seat power window don't work , the control from drivers seat or from the back seat door control, I popped both covers on the control switch and both are firmly plugged in, I don't have my meter with me to see if power is running back to the switch , this morning I'll try to switch out the two back seat controls to see if I can get at least that window to go down , 04 350 , would there be a fuse for each or is it in the switch in the door that the harness plugs into , that's the only window that won't go down...
View 8 RepliesFord 6.7L Power Stroke Diesel :: Heated Seats Quit Working?
The only problem it's had is the heated seats quit working.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Back Radiator Leaking / AC Quit
Recently turned 100k and since have had my exhaust RTD's go out. While fixing that they found the back radiator leaking. Since then both batteries died which didn't surprise me at 40 months. Then my windshield washer started leaking, then my DEF heater went out and two days ago my AC quit. I was ready to buy a new 2015 but now not sure. I've contacted Ford customer service and they are getting with the dealer to see what they may cover but haven't heard anything back yet.
Mine is a 2011 with 105,000 on it. This is pretty frustrating. I have been very pleased with this truck up until now it has been very dependable. However when that dependability begins to go south at only 100k it brings to question what exactly are we paying for here? A heavy duty truck that costs upward of 60k should be one you can count on for a lot longer than that. How Ford approaches this with me is definitely going to have a direct bearing on which 2015 diesel truck is in my driveway in the next few months. Again let me say that i have been very pleased with this truck and FOMOCO in general.
Ford 6.0L Power Stroke Diesel :: 2005 - Quit Running Now Won't Start?
I'm working on a 2005 F350 with a 6.0. The customer was driving the truck when it suddenly quit running and now it won't start. The only code stored in the memory is P2290 - ICP too low. With my scanner connected the IPR is showing 85% duty cycle and the ICP is only showing 5 psi while cranking. I disconnected the ICP sensor while cranking but still no fire, so I removed it and connected a pressure gauge which shows zero psi while cranking. I hooked up a cylinder leakdown gauge to the ICP port and with 100 PSI of air pressure I'm showing less than 2% leakage with the IPR energized at 60% duty. Thinking the hpop was bad I replaced it but still no change. I also tried a new IPR but no luck there either. I removed the oil filter cartridge and verified the low pressure pump is pumping oil while cranking. Could the inlet screen be plugged inside the oil cooler? I'm at a complete loss.
View 7 RepliesFord 6.7L Power Stroke Diesel :: Remote Start Quit Working
So just recently my remote start quit working. It's worked fine for the last two years. Now after I hit the buttons the truck just honks. I tried going through the setup on the dash and turning it off and back on. Still just honks at me.
View 8 RepliesFord 6.7L Power Stroke Diesel :: Gear Indicator Display Quit Working
So for 4500 miles since new my truck has been displaying, on the right side of the instrument display in the center dash, the actual gear the truck is in. I would shift from park to drive and move out and the truck would display what gear it was in by placing a lighted box around the gear number as it shifted 1-6. Now that display is gone. It's not anywhere. If I go to the manual mode it will display that, but the normal numbers from 1-6 , bottom to top , are gone.
View 14 RepliesFord 6.7L Power Stroke Diesel :: SYNC Voice Command Quit Working?
My SYNC voice commands witch I refer to as " Shiela" has quit working. No voice and it does not recognize phone. Just displays " no phone" ????
View 12 RepliesFord 6.0L Power Stroke Diesel :: Engine Suddenly Died / Restarted But Quit Again In Less Than A Second
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?