Ford 6.0L Power Stroke Diesel :: Truck Shut Down While Driving / Code P2614
So a few day ago my truck shut down while driving. I posted up and checked the ficm harness as suggested. Things were a bit lose so I zip tied my harness around the ficm. Thought it was all fixed and test drove it and it shut down again. I tried to start it a few times and my ICP was a tad low about 450 ,I have a brand new ICP and harness. Checked my scan gauge and I have code p2614. I cleared the codes and the truck started right up. I need to get this sorted out I was supposed bro go home tomorrow from working out of town all week about 100 miles from home...
View 3 RepliesFord 6.0L Power Stroke Diesel :: Sometimes Just Cranks / No Start
Like usual, i have a problem that no one else has and it sounds like its something electrical/sensor/PCM related.
Every few mornings, ill go out to my truck and go to fire it up...and it'll just crank away. After i give up on cranking and shut the key off, go to try again, it fires up instantly, like nothing is wrong. Sometimes in the morning itll just have an extended crank but eventually start. Regardless...it always starts. Sometimes it cranks really strong the entire time, sometimes the crank gets weaker the longer you crank...i don't think its HPO related, but i definitely could be wrong.
Ficm voltage looks good KOEO, cranking and running. I had my batteries tested at ford a few weeks ago and they "said" they were good (motorcraft 850ccas). Alternator is strong. When cranking, ive seen the voltage drop anywhere from 10.2 to 9.4v. I never know when this is going to happen and i can't hook up AE every morning and sit and wait, but based on my scangauge, i see ICP shoot up to over 1500 as soon as it fires.
Only code I've gotten is P0148, which is fuel delivery error/engine speed higher than expected. I've gone ahead and replaced my camshaft position sensor with a ford sensor a few days ago...it hasn't done a no-start yet, but it did do an extended crank. I think my next stop is PCM replacement...
Ford 6.0L Power Stroke Diesel :: Cranks But No Start
New alternator, fairly new batteries....after sitting 5 days or more, it cranks but no start.....put on charger for four hours, it fires right up...
Voltage on the multimeter shows 12.45 on both batteries......could there be something drawing down the amps? If so how do I find it?
Ford 6.0L Power Stroke Diesel :: 2007 - Cranks But Won't Start?
2007 6.0 my dash lights will flicker when the key is turned on and the truck wil crank but won't start, but when the lights stop flickering truck starts .. How to fix the flickering dash light?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Start After 3 To 4 Cranks?
My truck usually starts up great, but every so often it takes 3 to 4 long cranks before it will start. By long cranks I mean more than 4 or 5 seconds of turnover. Seems to be no real rhyme or reason to this. It does it engine cold or hot. I have iPhone engine monitor app and numbers seem fine. BTW it's a 2005.
View 12 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Cranks But Won't Start
I got a 2003 6.0 powerstroke cranks but wont start once it gets hot let it sit for a couple of hours and it fires right up already replaced high pressure pump no leaks visible and when running its great will run till run till fuel runs out. what to check?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Cranks But Won't Start - All Filters Clogged
Couple weeks ago fuel tank started coming apart clogged all filters. Replaced tank filters and fuel pump and blew out all of lines. Started and ran fine. Stays plugged in over night but now it'll crank but wont start. No codes showing up or anything...
View 1 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / Cranks Just Fine Just Doesn't Try To Run
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Cranks But No Start After Doing Head Gaskets
I have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 E350 - No Hot Start / Just Cranks But Won't Fire Up
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Cranks Over And Start But Sounds As If Hydro-Locking And Dies In Seconds
I have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2007 - Cranks But No Start - FICM / Cam / Crank Sensor No Sync
2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Engine Cranks Fine / No Cold Start
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Won't Start Just Cranks And Blows Black Smoke
I have looked through every post and idea possible with no remedy for my no start condition. I have tried everything that I am capable of doing without diagnostic computers and other specialized tools. A little history of what happened. While idling in the parking lot for a few minutes, truck all of the sudden start running rough, and acts like it is going to quit. Hurried out of the parking lot to make sure that I made it home, but the the truck would only get up to about 25 MPH, but I finally made it home(about 3-4 miles).
NOW, the truck won't start at all, but just cranks. Some more detail about how it cranks. It cranks fast, I separated the batteries by disconnecting the grounds on each, and made sure both are charged. Batteries are only 3 months old from Ford Dealership. As the engine cranks, oil pressure registers after a little while, (longer the first time for some reason), and as soon as oil pressure shows up on the dash indicator, black smoke starts coming out of the exhaust. The engine is trying to start a little bit, but it mostly just cranks.
Things that I've done: Changed fuel filters, Motorcraft (new orings). At first the pump was pumping large bubbles through the line up into the upper fuel filter, but after sitting it appears that it is not pumping bubbles anymore, and I cycled the Key more than 10 times. Did the bubble test while upper filter was removed. Unplugged ICP sensor. Pulled EGR, installed new one. Pulled oil filter and made sure that oil is pumping.
Checked FICM voltage, with key on Injectors buzzing, also engine cranking for quite a while. Never dropped below 48.5 V. Pulled FICM just incase and performed repair procedure, still same volts and no start. Coolant level is good. Checked oil level. unplugged EGR. Checked filter Minder. checked for chafing on FICM harness. Unplugged MAF. Checked FICM relay operation, Fuses all around. I need this truck to run.
Ford 6.0L Power Stroke Diesel :: 2007 F250 Would Not Start - Cranks Fine And Almost Started Once But Died
Went out to start my truck this morning and it wouldn't start. Cranks fine and almost started once but died. Checked all fuses all my voltages are good. Oil and coolant are good. When I turn the key on I can hear the fuel pump and sounds like it's priming correctly. Might be an issue with a clogged fuel filter? Maybe? Haven't had any problems or issues otherwise.
View 6 RepliesFord 6.0L Power Stroke Diesel :: Code P2290 - Start But No Power
Long story behind it but finally got my scanner working right and checked the suggested systems for p2290.
IPR was 77+ on start up dropped to around 31 at idle
FMP is in the 46.5 to 47.5 range
SYC was at 1 and occasionally at 1.5
ICP was at 550-650 during startup and quickly ramped up to 1150 then settled into around 850 at idle.
The only thing that I'm not sure of is the IPR being 31 at idle, is that what it should be. The others I think are within normal operating parameters.
The truck starts but has no power. Can barely go up a slight hill on my street. Seems like it's going to be fine but as soon as I apply a little gas it just falls off.
Ford 6.7L Power Stroke Diesel :: No Start - Got Code P2291 Low ICP?
I was working out here on a site north of OKC and the truck has been running great all day. I shut it off to do the job and 20 mins later it will not start. I pulled the codes P2291 low ICP. One thing I noticed is that I cant hear the lift pump running when I turn the key on. I even drained the bowl on it and still can't hear anything. So I'm thinking bad lift pump or something.
View 14 RepliesFord 6.0L Power Stroke Diesel :: No Start No Crank / Code P2285
So I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).