Ford 6.0L Power Stroke Diesel :: 2005 F250 - Engine Cranks Fine / No Cold Start
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / Cranks Just Fine Just Doesn't Try To Run
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Cranks Fast And Fine But Won't Fire Up And Start
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Power Loss / Died And Now Cannot Get It Started
While driving home the other night at highway speed my truck lost power. I just filled the tank about 15 miles before then and everything was running fine. No lights came on the dash before the truck died and now can't get it started. Bad fuel? Clogged filter?
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Died While Driving And Won't Start
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2007 - Cranks But Won't Start?
2007 6.0 my dash lights will flicker when the key is turned on and the truck wil crank but won't start, but when the lights stop flickering truck starts .. How to fix the flickering dash light?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Won't Start Just Cranks And Blows Black Smoke
I have looked through every post and idea possible with no remedy for my no start condition. I have tried everything that I am capable of doing without diagnostic computers and other specialized tools. A little history of what happened. While idling in the parking lot for a few minutes, truck all of the sudden start running rough, and acts like it is going to quit. Hurried out of the parking lot to make sure that I made it home, but the the truck would only get up to about 25 MPH, but I finally made it home(about 3-4 miles).
NOW, the truck won't start at all, but just cranks. Some more detail about how it cranks. It cranks fast, I separated the batteries by disconnecting the grounds on each, and made sure both are charged. Batteries are only 3 months old from Ford Dealership. As the engine cranks, oil pressure registers after a little while, (longer the first time for some reason), and as soon as oil pressure shows up on the dash indicator, black smoke starts coming out of the exhaust. The engine is trying to start a little bit, but it mostly just cranks.
Things that I've done: Changed fuel filters, Motorcraft (new orings). At first the pump was pumping large bubbles through the line up into the upper fuel filter, but after sitting it appears that it is not pumping bubbles anymore, and I cycled the Key more than 10 times. Did the bubble test while upper filter was removed. Unplugged ICP sensor. Pulled EGR, installed new one. Pulled oil filter and made sure that oil is pumping.
Checked FICM voltage, with key on Injectors buzzing, also engine cranking for quite a while. Never dropped below 48.5 V. Pulled FICM just incase and performed repair procedure, still same volts and no start. Coolant level is good. Checked oil level. unplugged EGR. Checked filter Minder. checked for chafing on FICM harness. Unplugged MAF. Checked FICM relay operation, Fuses all around. I need this truck to run.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Intermittent No Start / Idle About 15 Minutes And Died
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Truck Cranks Over Fine But Does Not Fire
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2007 Truck Won't Start / Died While Driving
I have a 07 6.0 that won't start it died a few weeks ago while driving. Being a mechanic I've done numerous things to the truck in order to fix all the common 6.0 problems but can't figure this one out. It will crank and get oil pressure and fuel pressure but seems to not be getting fuel. The IPR valve isn't clogged I tried with 2 working valves nothing worked. Along with changing the ficm. The connections to the ficm are clean and all in tact. I have an edge evolution chip that isn't even showing any codes. Not sure what to try next since I don't have any codes to go off of.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2007 - Cranks But No Start - FICM / Cam / Crank Sensor No Sync
2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 - Cranks Just Fine / Slow To Start
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Intermittent Crank / No Start
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Starts Fine Then Dies After 2 Minutes
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
Ford 6.0L Power Stroke Diesel :: 2003 F250 Cranks Then Stops
So I have a 03 f250 6.0 with 285,000 miles, when I shut the truck off and let it sit for like 20 mins and go to restart it, it cranks then just stops and I hear what I think to be the starter still turning till I let off the key. It'll do this for a while sometimes. So what do y'all think it could be? P.s I know it's very bad for the truck, but I have ran out of fuel about 9 times on the stock pump because my fuel gauge is off, and after the most recent breakdown is about the time it started.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Cranks But Won't Fire
I just bought an 04 Ford F250 diesel 6.0 with 92k miles. Previous owner installed a UNGO alarm with remote start. Last week, after work, I started it using remote start. I got in the truck and realized I had forgotten something, so I exit the truck and leave the keys on the seat. Truck is still running. The doors lock. I reached in through the cracked window and pushed the unlock button. Here's the problem.. the truck died immediately won't start.. mechanic says it's the high pressure oil pump. I'm thinking it's the anti theft system but no luck.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Lost Power Then Died
My 2006 F250 was towing my 5th wheel when it started to loose power and eventually died. Would not restart. Replaced all fuel filters to no avail. Towed to mechanic shop. Has a little over 100,000 miles on it. Waiting for mechanic to check it out.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Just Died All Of A Sudden - Intermittent Power Loss
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
Ford 6.0L Power Stroke Diesel :: F250 - Cold Starts Fine / Stalls Immediately After / No Throttle Low RPM
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.