Ford 6.0L Power Stroke Diesel :: New Injectors - Now Truck Takes Almost Two Seconds Of Cranking To Start Engine
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
Ford 6.0L Power Stroke Diesel :: 2003 - When Cranking Low Oil Pressure Comes Up On The Gauge
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
Ford 6.0L Power Stroke Diesel :: Long Cranking When Warm / Pressure Too Low
Some information about the truck2004 Excursion, Motor has a December 2003 built date listed on the valve cover
Bullet proof complete by Hallas performance just prior to Mike's passing (3 years ago). ARP, EGR, Oil Cooler, lifters, etc..
Newer batteries, DC amp 185 alternator, newer starter, she cranks hard and fast~230,000 miles
Here is the situation: Starts good and fast when cold, even subzero temperatures. She cranks long and barely catches if I make a short stop at a store or restaurant. A few hours later or the next morning is fine.
I found the following codes:
P2284 - Injector Control Pressure Sensor Circuit Range/Performance
P2291 - Injector Control Pressure Too Low - Engine Cranking
P0528
I took her into the local Ford Dealer for diagnosis and here's what they reported. ICP tests good and has the latest pigtails. They reported a leak in either of the following.
Oil injection pump Estimate of 8.5 hours to repair.
Under the Valve Cover Gasket. Estimate of 3.5 hours to repair.
So here are the questions I have. Does this diagnosis sound appropriate? Is it reasonable that they do not know which area is causing the problem? Are the hours reasonable estimates for the repairs? Assuming I go ahead with these repairs, is there anything else I should have them look at while they're in there?
Ford 7.3L Power Stroke (1999-2003) :: 2002 F550 Taking 4 Seconds Of Cranking To Start Consistently Hot Or Cold
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
Ford 6.0L Power Stroke Diesel :: Won't Start - Voltage From 11.5 To 10.5 While Cranking?
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Cranking But Barely Tries To Start
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start / No Cranking
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Truck Only Cranking And Refuse To Start
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 RepliesFord 6.0L Power Stroke Diesel :: No Start / Cranking And Large Pop Noise Came From Under The Hood
Had Just replaced glow plugs and batteries along with a new set of tires. Truck had been running fine for the three days that is was. Went out the next morning and went to start and "POP" a large noise came from under the hood. I have yet to discover where this noise particularly came from or what it may have been that caused it. But ever since the POP it will not turnover what so ever. Key on every thing is normal all power just when go to turn key over it makes a faint click. You can feel the click in the relays on your hand when you try to turnover. But nothing. I am absolutely clueless.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Harder Cranking And Would Not Start Cold - Code P0405
This morning when attempting a cold start of my 05 6.0, it would not start was noticeably harder cranking. I had no CEL. I checked my scan Guage and the volts were 13.4 and fcm main power was 48.4. I checked and I had a p0405 code. What could be going on? I read that it can be a stuck or bad EGR valve? Could it be battery related?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Truck Started Cranking Longer Than Normal To Start After Sitting For More Than 2 Hours
About 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 RepliesFord 6.0L Power Stroke Diesel :: Cranked For About 15 Seconds With No Start
This morning I went out to start my truck. It cranked for about 15 seconds with no start. I set my TorquePro to monitor the IPR% and cranked again for about 10 seconds. The IPR% was about 83.7% with no start again. I went inside and searched for "crank no start" threads to see what else I needed to look at. I went back out and added HPOP to the TorquePro. Cranked for about 5 seconds, thinking I would get no start again, but it fired up. After start I was getting about 27% on the IPR and abour 537 on the HPOP. Drove to work with no problem.
Could this just be a fluke, or do I need to be concerned about it? I have a road trip coming up to Tennessee on Thursday. I did standpipes, dummy plugs, STC fittings, EGR delete, new oil cooler and upgrade to stainless steel IPR screen about a year ago.
Ford 7.3L Power Stroke (1999-2003) :: Starts But After 5 Seconds Of Cranking Even Warm
I am a longtime 7.3 IDI guy with an 88 F350 crew so i know about diesels. But this is my first electronic diesel. I picked up a 2001 F450 2wd auto 260k miles. it used to be my work's truck but was stitting for a year and now i got it in "non running condition"
I towed it home and got it started by replacing the batteries and using the block heater.
As expected it took a few tries of long cranking to run the first time. runs pretty good and no smoke. what surprised me is it still takes about 5 sec of cranking to restart each time when warm too. any direction you would look with those symptoms? HPOP, IPR?
i am pretty sure the glow plugs all work because mechanics had replaced all that stuff. but i know back when the truck was last used it would still never start cold unless plugged in (even in summer).
Ford 6.0L Power Stroke Diesel :: 2006 - Won't Start When Hot - Oil Pressure?
Background: My 06 started up and ran fine until #7 injector took a crap.I had the injectors replaced with 155/stocks from warren.
Well no we're having an issue with a hot no start. Starts and runs just fine cold but once up to temp and you shut her down you can't start it again till it cools. Air tested it 3 different times can't find any leaks. Swapped out the ipr with a new one my mechanic had just to see and no change, unplugged it and no change.
What it could be. When warm and trying to start it only gets 300psi. The only other thing i can think of is hpop, but to go just like that without any trouble before hand has me puzzled.
Ford 6.0L Power Stroke Diesel :: 2004 - No Oil Pressure At Start Up
I have a 2004 late model 6.0. My son was driving it and parked it in the road told him move it and it wouldn't start. I got it to start and it ran for about 10 seconds. I pushed it in the drive way and left it over night. In the morning there was oil on the driveway. I found that there was the wrong oil filter put in and there is no oil pressure at start up and no oil entering the filter housing. Where to start would be great. I am going to get a Scangauge II to get more information. Could be the ICP?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: New HPOP And Injectors - Long Cranking About 15 - 30 Seconds
I recently did the following work:
New Injectors
New T500 Hpop
New IPR
New ICP Sensor
New UVCH/Glowplugs
New starter
Been cranking about 15-30 seconds each time about a dozen times now. I've pulled the icp and the hp crossover and have oil flowing at each.
ICP builds to about 240 psi and at a 98% duty cycle....so I assume there's still some air in the system. I"m not getting any sense that the engine is trying to hit. Do i just keep cranking?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Not Enough Pressure To Start
I have a 2003 F-250. For 8 months now we have been trying to get my truck to start. We have replaced the High pressure oil pump, Oil cooler, PCM, Main wiring harness, FICM, Injectors,, ICP, and IPR. Still we are not getting enough pressure to start the truck. What is happening is the pressure will get to about 340 and will not increase from there. If we are to disconnect of one the connectors from the FICM the pressure will reach 640. Now we are able to get the truck started with ether, but will not remain started. As of right now we are still trying to figure out what is causing this problem?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Cranks Over And Start But Sounds As If Hydro-Locking And Dies In Seconds
I have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Turn Over For 30 Seconds After Cranking / Engine Starts To Run Roughly Then Die
I have a 2002 F-450 crew cab 2wd automatic 7.3 diesel with 298k on the body and about 120k on a Jasper engine. About a month ago I started it in the morning to let it warm up. Went to make coffee. Came back and it had died. It was low on fuel and I didn't pay attention. Played hell getting it primed back up. Now if I don't let it warm up for twenty minutes it won't run worth a flip and has been dying out. Changed fuel filter. Unplugged ICP. No change. When I crank it it will turn over for about thirty seconds then oil pressure gauge moves, then engine starts to run very roughly. It will die. I repeat a few times. It will eventually start and start and stay running. Blows whitish grey smoke until it warms up. No loss in power till CEL comes on. Still not too much loss. Sometimes it takes a long time to get it running. Sometimes it will die after I get out of the driveway if I don't let it warm up. Truck was serviced maybe 3000 miles ago. No water in fuel. New fuel filter. New air filter. It is a company truck. I work for a small company building cell towers.
View 5 Replies