Ford 6.0L Power Stroke Diesel :: Fuel Pressure Gauge Install
I finally received all the parts needed for installing my fuel pressure gauge, but I am wondering if I am going to need a schrader valve on my fuel pressure line going to the sending unit, or if I am going to be safe with just doing a 6 time cycle of the fuel pump like we do when we change out the fuel filters. Seems like that should work for getting the air out of the fuel lines, same concept I would think.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Fuel Pressure Gauge Dropped Down To 50 Then Back To 65 At 70 MPH
Well, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
Ford 6.0L Power Stroke Diesel :: 2006 - Possible To Monitor Fuel Pressure With Gauge While Running?
OK so 2006 f550 6.0
If I want to monitor fuel pressure with a gauge in cab while running all the time... (not just testing) can I purchase one of the secondary fuel filter caps that have a port in the top and connect the sensor to this to run or is there a better way? (Or is that not going to work)
Cap I am talking about is something like this
[URL]
(I know this is a combo kit but they do sell the fuel only) But since it has a threaded port in the top I could connect the fuel pressure sensor to that and go from there correct? Would that give accurate readings?
Ford 6.0L Power Stroke Diesel :: 2004 - Fuel Pressure Gauge Is Reading Dead 0
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Fuel Level Back Light And Oil Pressure Gauge Out?
The backlight for my fuel level and oil pressure dash gauges are out. Would that require a simple bulb replacement or if there is something more difficult to replace, i.e. entire panel? The red needles illuminate, it's just the gauges themselves that are dark. The truck is my 05 Super Duty in the siggy.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Return Line Leaking At Fuel Bowl
New to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
Ford 6.0L Power Stroke Diesel :: Oil Pressure Gauge Showing No Pressure
Last week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Line Leads To Head Under Turbo Leaking?
The fuel line on the passenger side under the turbo that leads to the head is leaking looks like from rubbing on the pedestal, anyone ever just cut it and throw in some fuel line and hose clamps?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Reconnect High Pressure Oil Line To Rail?
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Low Fuel Pressure And Reduced Pressure Limp Mode
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 RepliesFord 6.0L Power Stroke Diesel :: Hydroboost High-pressure Line Coupling Leak - Replaced ORing?
I've been watching fluid build up on what I think is the hi-pressure line on the hydroboost. It appears to be originating at the coupling in the line because it is dry back at the unit.
Is there an o-ring or nylon washer in this fitting?
Can it be tightened?
Does the o-ring or washer need to be replaced?
Is it a sign of something else, like a build up of pressure in the line that is too high?
I currently have zero problems or noise coming from the steering or brake system.
Ford 6.7L Power Stroke Diesel :: Whining Sound / Low Fuel Pressure And Reduced Power Warning - Fuel Pump Just Died
So, I just had the fuel pump replaced on my '15 6.7 a month ago and it just died again. (next day edit: it didn't actually die, it showed all the same symptoms)
Same symptoms: whining sound, low fuel pressure warning, reduced power warning.
This time I'm 50 miles from home so I pulled off the road before it shut off. Interesting, I was in a hilly area and my low fuel warning came on too. We are waiting for a tow. I was considering trying to push on but don't want to get stuck in a dangerous spot on the highway. We're in a church parking lot.
So, last time this happened I was on flat road with about a half tank of fuel on a lunch break. I ran a mile after the warnings came on to feel out the issue and to see what would happen. I happened to be only about a mile away from my dealer so I drove that way. I got reduced power warning and then it cut power on me (limp mode). I made it to about 100 yards away before it cut off.
This time, I was in a hilly area at night on a windy two lane road with no shoulders in the woods. I was miles from civilization and was showing below a quarter tank of fuel. ~100 miles to EMPTY. I got the low fuel pressure warning first and then the reduced power mode before the whining noise started. I was climbing a hill on a curve at the time. I drove a quarter mile and then pulled off the road into a parking lot so I wouldn't be stuck on the shoulder. It didn't actually go into limp mode.
I let it sit a few minutes, talked it over with the wife and decided to call for a tow. After talking to the tow truck driver who said he would be an hour because he had to go find a bigger truck, I decided to see what I could do while I wait. I fired it back up and the fuel level dropped to below 1/8 and I was now showing 33 miles to EMPTY. I was parked on a hill with the back end up. I had backed the truck into a space to make it easier for the tow truck driver. I let it run a minute, checked for leaks and it seemed to run fine with no studdering or additional warning lights.
CEL was on but no new warnings. I put in my code reader and pulled the P0087. Just one code. I revved it a bit to see if there were any issues. It seemed fine so I decided to try my luck. I started driving towards home with the intention to stop at the first diesel station to fill up. Truck ran fine. After two minutes of driving gently, heart racing, my fuel level came back up and it now read 88 miles to EMPTY. I drove 11 miles to the nearest station and filled up. No issues. I shut it down. I fired it back up. Still no issues so with a full tank, I drove home the remaining 30 miles without issue.
Planning to take it in to the dealer Monday to get it checked. Could this be from an air pocked due to low fuel level and hilly terrain? Is my new pump dying already? Is there something else going on inside the tank or elsewhere?
Ford 6.7L Power Stroke Diesel :: Aux Fuel Gauge And Fuel Pump Both Quit
I have my aux fuel tank pump hooked to upfitter 3. It has worked perfectly until this week. I started to transfer fuel and the aux fuel gauge and fuel pump both quit. The led on upfitter switch 3 still illuminates, but no fuel pump. I found fuse 9 on passengers kick panel is for upfitter 3. The fuse was good. Is there another fuse somewhere for the circuit I've missed? I can trouble shoot the wiring if necessary, but it's tough to do all behind the left side underbed box and not easy to get to. I've missed something simple before I go further????
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Installation Of Fuel Pressure Gauge?
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Pressure Gauge Installation
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 RepliesFord 6.7L Power Stroke Diesel :: Oil Pressure Gauge Installation?
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure Gauge Not Working
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Oil Pressure Gauge Says Zero?
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 RepliesFord 6.7L Power Stroke Diesel :: Misfire - Smoke - Fuel Injector Supply Line?
Went to go and start my truck this morning and noticed after it was running that it sounded like a misfire, then i seen the smoke... I shut the truck down and lifted the hood and seen that somehow i had a high pressure fuel injector supply line on the Lh side break off. The line that goes from the fuel rail to the injector port on the valve cover (theres 4 of them on a side). There doesn't seem to be an o-ring or anything on them, they are just pressed over and tighten down.
View 6 Replies