Ford 6.7L Power Stroke Diesel :: 2011 F250 - P1635 Code Won't Clear
Bought a 2011 F250 with P1635 code. It has 35x12.50 tires my Sct x4 tuner only goes up to 34 inch tires. Im new to the 6.7 diesel game previously had 6.0 and want to hear from yall what to do.
View 1 RepliesFord 6.7L Power Stroke Diesel :: Code P1635 - Tire / Axle Out Of Acceptable Range
I was updating the firmware on my mini max tuner today and decided to calibrate for the 37" tires. After calibration was done I got the code P1635, which is "Tire/Axle Out of Acceptable Range". Should I bring it back down to 34" where the FORD ECU stops calibrating? I mite have lost traction control with this calibration as well. Mite find out tomorrow if I get an itchy foot. Truck seemed to drive better and pull harder off the line....low rpm's.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - CEL Is Always On / Error Code P1102
6.0 diesel 83,000 miles. My CEL is always on and my Edge gauge says it's lower than expected Mass air flow. I've changed the filter, cleaned the MAF with special cleaner and then replaced with new. I've replaced the EGR valve.
If I clear the codes and run it I don't get a CEL until I turn it off. But the next time I start it, there it is again. My Edge reads 0.0-0.3 MAF while running but what that means. One end of my cleaner box is slightly warped but I can't feel any noticeable leakage.
Everything runs fine but I would like to regain the ability to have that idiot light available to tell me if I have a new problem.
Ford 6.0L Power Stroke Diesel :: Error Code P0400 After Doing Stealth Egr Delete
I just did a test drive with my 04 6 liter, I did the stealth egr delete. I had a P0400 error code any concern?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Remote Access Installed - Error Code 00011000?
I've had the Ford Remote Access installed on my pickup for over a year now and it's worked great up until about a week ago when I changed cell phone providers from AT&T to Verizon. Now when trying to use the app I get the error code 00011000. I up-dated the app to reflect the new carrier but it still doesn't work. And yes, my subscription to the service is current. What I need to do to get this working again, with winter just around the corner I'd sure like to have this functional again. I figured I'd give the forum a shot before I resort going to the dealer.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Error Code P0475 - Fix?
I went and got my truck smog and it failed because of this code. I then changed the sensor cleaned out the tube and I still can't figure out how to get rid of the error code?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Got Error Code P1464?
Well I thought my truck was 100%, and I was going to installed a Chip. I decided to get my Forscan up and running to check and make sure.
The Buzz test Passed with no problems.
The cylinder contribution did not pass. I got error code P1464, which Forscan said that #8 failed. FYI, I turned the A/C on and the test failed. I ran it again with the A/C off and it failed again. I might have the wrong code
I then went to where you could select the gauges to view(PID's). And I saw where you could select all the cylinders injectors individually. I forgot what it was called, but all injectors were reading close to 0.0% at idle except for #8 it was reading 5.55% to 5.88%.
I am hoping this is good news, since I rather the injector be bad then a piston ring or valve. I just got the Forscan and was wondering what other test or other things I could check to narrow the problem down before removing the Valve covers. The truck runs great and there is no miss and it turns over smooth. No blowbye, just runs great. It is a 2000 F-350 dually with just over 202,000 miles
Ford 6.7L Power Stroke Diesel :: Got Error Codes P220c And P220e?
I had incorrect codes its a p200c and p200e
I know this has been talked about but im not having the same results when doing tests
Truck had a ruff fri night. Getting on I state with trailer loaded and it said STOP SAFELY NOW shut donw before i got it under 30 mph. Had it towed back to our shop and started to figure out what was wrong. I have heard of egt 12 and egt 13 sensors going bad. so i un plugged them and put a test meter to the first three all came back in the 216.00 range which is in standard for what my buddy's tested at.
Ford 7.3L Power Stroke (1999-2003) :: Got Error Code PO475 - Location Of DFPE?
I'm trying to get my truck smogged and having problems w/po475. A friend of a friend said it was the DFPE sensor. So I bought one but can't find where it goes. On YouTube it is only listed for F150's and gas motors it seems. I have a 00 f350SD 7.3, do I even have a DFPE and if so where is it located.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Error Code P0472 - Low Boost / 0 PSI EBP?
2000 truck, 334k, automatic 2wd, stock. Have low power, 11psi max.
Permanent p0472 code, can't clear it even temporarily. The moment I turn the key to Acc, code is there. It's the only code showing on Forscan.
Tried 470ohm 1/2watt resistor, in two turbo pedestal sensor connector wires, no change. Forscan shows 0.0-0.6 psi EBP value when running.
No change with pedestal sensor plugged or unplugged. Resistor or not. Truck starts and runs good, low power is the only issue.
Sensor and tube are new. Seems like wiring is bad, where to look next to track this down?
Ford 6.0L Power Stroke Diesel :: Check Engine Light Go On - OBD2 Error
I had a bad Glow Plug on my 2004 F350 6.0L Diesel causing the check engine light to go on. I replaced the Glow Plug and cleared the OBD2 error. The check engine light is off now, but I can't pass the smog check because EGR Monitor "Not Ready"
I put 100+ miles city/freeway miles on the truck, but I still get EGR Monitor "Not Ready" Even tried "Drive Cycle" with no luck...
Ford 6.0L Power Stroke Diesel :: SCT Gauge Updated - Now Getting General Error 21000?
My SCT X4 tuner was not loading the gauges, so I updated it and then the gauges started working. Then I check the codes and it came up as "General error 21000".
View 1 RepliesFord 6.0L Power Stroke Diesel :: Glow Plug Code And CEL Code P0675
Truck has been running very well while in the warmer North Carolina climate pulling trailers with no limp mode or wrench light. However, when daughter started the truck this morning, SGII showed one DTC and when she pulled it up it was P0675. OK, glow plug num 5 maybe or the module. No issues starting or rough cold idle. I told her to clear the code and we'll see if comes back.
She did ask if it is something she should have it repaired before the trip back to Vermont. So I thought I'd ping the group here since reading posts, they seem to be fairly easy to replace (and assuming it isn't a chafed wire) and I could probably save her some $. Just want to make sure there isn't any chance of real engine damage.
Ford 6.7L Power Stroke Diesel :: 2012 F350 - DEF Error Messages / Shutter And Knocking Noise
Just bought a 2012 F350 6.7 4x4 in the beginning of March. After about 500 miles the "Exhaust Fluid System Fault - In 50 miles, speed limited to 50 mph" message displayed. So first thing that occurred to me was maybe it was low on DEF, so I added approximate 1.5 gallons as it had some already in there. I also called the dealer who said "well it just needs to be driven on the highway" hmmm, that sounded weird but I did it anyways. After that I started the truck and the message was gone. I thought that fixed it. - Nope, at about 1480 miles I got the same error message again.
So after getting the message again I just kept driving and the message went away. I thought ok. Yeah right! Now in the past few weeks I have been noticing that the truck almost wants to stall and begins to shudder when going over a slight incline and shifting from 5th to 6th at about 45mph. When I accelerate it makes a knocking noise. If I let off the accelerator, let it slow down, it downshifts into 5th and I then accelerate and it goes away.
And today... I decided to go for a nice ride. After about 10 minutes of driving I get the ole "Exhaust Fluid System Fault" error again. Crap! Again, I keep driving and after another 15min - I get that shutter and knocking noise. Anyway I drove until the the truck displayed "Speed limited to 50mph on next restart. I just kept driving and the error message mysteriously disappeared again.
Ford 6.7L Power Stroke Diesel :: CEL Code P02E1 - Diesel Intake Air Flow Control Performance
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.7L Power Stroke Diesel :: P259F Code / Reduced Power Mode
It happened to me. I was 2 hours into my trip and towing the camper when I got the reduced power CEL. I have 28,000 miles on my truck and always tow in "tow/haul" mode with the exhaust brake on. I was lucky in that I has on a limited access highway and just happened to be approaching an exit to a fuel station with big rig access. I limped in there at about 20MPH checked the code with my Forscan lite and found the P259F code. I typed that into Google and found a thread on another Diesel forum! Some guys said it went away after 3 or 4 restarts. So, I tried a couple of restarts...no luck.
I was down to half a tank of fuel so I filled up and parked. As long as I was parked, I went into the camper and used the bathroom. When I got back in the truck, I thought about the WiFi scan adapter plugged into my OBDII connector and wondered if I should unplug it. I did and everything worked! So, I drove the next 4 hours in "tow/haul" mode, but I left the EB off. I also never plugged in the WiFi scan adapter because I didn't want to risk going into the reduced power mode again. Anyway, we made it home without incident. One of the reasons I traded my 2013 in on a 2015 was to get the engine improvements and the EB. I sure don't want to give up the EB. I'm going to take mine to the dealer, but after reading this post, I'm not expecting anything much.
Ford 6.7L Power Stroke Diesel :: Significant Reduction In Power - CEL And Code P208E
Got this nugget this morning after dropping my daughter off at school. I also noticed a significant reduction in power. Had to get fuel so while pumping, I checked the code with my WiFi reader and Engine Link app.
Got the code number which came up with this: 6.7L ? MIL on with DTCs P208E P218F P204F ? 2011-2016 Ford F-Super Duty
I decided to clear the code and see if it would instantly return which it didn't. Power came back as soon as it was cleared too. Will see if it comes back. Looks like the code is saying there might be crystals on my DEF injector. I did have a regen last night right before I parked for the evening and then this showed showed up first thing this morning. Would a DEF injector nozzle be covered under the emissions warranty if it comes back?
Ford 6.0L Power Stroke Diesel :: Code P2290 - Start But No Power
Long story behind it but finally got my scanner working right and checked the suggested systems for p2290.
IPR was 77+ on start up dropped to around 31 at idle
FMP is in the 46.5 to 47.5 range
SYC was at 1 and occasionally at 1.5
ICP was at 550-650 during startup and quickly ramped up to 1150 then settled into around 850 at idle.
The only thing that I'm not sure of is the IPR being 31 at idle, is that what it should be. The others I think are within normal operating parameters.
The truck starts but has no power. Can barely go up a slight hill on my street. Seems like it's going to be fine but as soon as I apply a little gas it just falls off.