Ford 6.0L Power Stroke Diesel :: Battery Light Lit Up On Dash - Voltage Drop And P0528 DTC
My Battery light came on on my dash and my scangauge 2 was reading 11.5/11.4 volts yesterday afternoon, I ran for codes on my obd-2 and P0528 came up. I picked up one new battery and put that in to see if that would bring my voltage up at all. Today it was reading 11.3/11.2 volts. From what I've gathered the P0528 is most likely the fan clutch or the harness connecting the fan clutch to the PCM.
I've seen the water pump replacement write up that shows how to pull the fan assembly. My questions are - can the fan clutch be replaced without draining/pull the radiator? or is it better off to just do the coolant flush and pull the radiator. And would the fan clutch/harness issue drop the voltage or would that just be two bad batteries?
Ford 7.3L Power Stroke (1999-2003) :: Battery And GPR Voltage Dropping?
I do run a small battery maintainer during the winter months plugged into a three way with the block heater. Alright after sitting out side for approx 9-10 hrs in 22 degree weather I did these checks. Battery voltages at 12.55V and 12.6V on batteries.
Voltage coming into for was also 12.5V. When glow plugs activated I am getting 11V on the other side of the gpr. After cycling glow plugs battery voltages drop to 9.6V during cranking and as soon as she starts back to 12.5V.
Do these numbers sounds right? In my opinion isn't the drop to 9.6V during cranking a little low or is that the normal?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Battery Light Comes On / Voltage Does Not Drop
Bit of a confusing one as of late. Doesn't happen every time I drive, maybe 50% of the time. When I start the truck up, torque pro reads voltage at 13.9-14.1 consistent. After 30 minutes it usually drops to around 13.7/13.8. Sometimes, battery light comes on, voltage doesn't drop. I can drive the truck, park it, turn it off, restart, no side effects.
I notice if I stop, turn off the truck, and restart it, torq pro will begin to read a voltage of 12.8.13.0. Sometimes it won't budge for an hour, sometimes it climbs right back up to 13.8, sometimes the battery light goes off, sometimes it stays on.
Alternator was replaced a month ago, both batteries replaced a week ago, all terminals cleaned and secured at the time of replacement. Truck behaves perfectly normal, I'm almost at the point of putting a piece of tape over the light and ignoring it, but was curious before I go that route.
Ford 6.0L Power Stroke Diesel :: FICM Code / Low Voltage
I replaced injector couple weeks ago. I hooked up to livelink thru sct because it was throwing a low voltage for ficm code. It is staying at 48 volts tho. I don't see any voltage from my glow plug relay, and I have a low voltage for my egr valve. Is it just bad luck that everything broke at once or is there a fuse or a connector that I forgot to plug in.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Won't Start - Voltage From 11.5 To 10.5 While Cranking?
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 RepliesFord 6.0L Power Stroke Diesel :: FICM Going Out - Voltage Dropping
I'm afraid my FICM is on its way out. I'm getting voltages dropping to 46.5V about once a minute. Never goes below that. Then it'll bounce up to around 48.5. It gets low when I have to rev up and always coincides with the main voltage dropping to around 12.9V.
Now for my battery condition. They are about a year old. I think I have one with a bad cell. They'll drop into the low 11V range while cranking after glow plug light goes off. While driving, the main voltage never gets below 13.1 except for very short periods ... which coincide with the 46.5V output on the FICM. Gonna have them tested separately at advanced auto and see on has a bad cell.
So, is my FICM starting to go? Second question. What do I tell the folks at Advanced Auto about replacing both an not just one? I suspect they'll want to argue about it with me.
Ford 6.0L Power Stroke Diesel :: Loss Of Power / Codes For Low Voltage / FICM And Cylinder 6 Misfire
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
Ford 6.0L Power Stroke Diesel :: Low FICM Voltage At Cold Start
So I am getting low FICM volts at cold start. The FICM will start at 46v and eventually drop below to 42v, but when I start to drive the truck the FICM volts go back up to 47.5, and my battery voltage goes back up to 13.8 to 14.1.
I am pretty sure my alternator is doing its job.
I left my truck sit for 2 or 3 weeks with out starting her or putting a battery tender on it, this was about two weeks ago. I have not had this problem before. Sounds to me like the batteries need a charge.
My batteries back up to full charge. I plan on letting the truck sit over night with a charger hooked to it.
Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Start - Battery Voltage Will Keep Falling If Cranking Continues
So when its cold and im talking below 55 degrees, and the truck hadn't been started that day, it will turn over 3 or 4 times before the voltmeter takes a dive down to 10 volts or so and doesn't start. The voltage will keep falling if cranking continues. I took the batteries out and had them tested. They are both above the rated cca. So im thinking it could be the starter windings?
I did replace an injector recently so all the cranking to get it going again may have ruined the starter? But when I hook up the battery charger and jump the truck it starts. And after it has been started it will continue to start easily the rest of the day.
Ford 6.0L Power Stroke Diesel :: FICM Voltage Drops Ar Higher Speeds
At idle it stays at 48.5v-47.5v But as I pick up speed it continually drops. At 70mph it gets as low as 29v. But will go back up slowly as I let off the throttle.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - CEL Code For Injector Voltage Being Low
I have a 2006 F-350 4x4 CC LB. I recently had my check engine light come on coincidentally on my way to the auto parts store. Asked them to plug in the scanner and read the code. It had around 20! This truck has 40000 miles on it. All of the codes were dealing with injector voltage being low. All eight cylinders. So I'm thinking ficm is going out. I replaced the batteries shortly after this. I driven it a time or two after this and it started cutting in an out going down the road. Seemed down a few cylinders for a few seconds and pouring black smoke from the tailpipe of a stick truck. Made it home after it did this there times. Stated it up to move it a few days ago. Some white smoke that clears quickly and ran rough for a few, pulled it in gear surged forward and died. I cleaned the EGR valve and re o ringed it. Tested the drivers side pin on the FICM and have 47-48 volts with key on and cranking.
View 4 RepliesFord 6.0L Power Stroke Diesel :: FICM Voltage Drops To 40 On Cold Mornings
I've noticed on mornings when it's around freezing or colder my FICM voltage drops down to around 40. after about a minute it creeps up until it's in normal range, about 48 volts or better. This only seems to last about a minute before it's in normal range. No check engine lights though.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Low FICM Voltage Under Acceleration?
Pulled the trigger today and bought a 2004 F350 DRW King Ranch with 200000 miles. Using Forscan Lite on my iPhone, KOEO FICM voltage was right at 48. During start it went up a bit. While out for my highway road test for EOT/ECT differential (never went above 10 degrees).
I noticed that the FICM voltage would drop to the bottom of the Forscan scale (40 volts) when I was accelerating and then go back to 47.5 when I reached my cruising speed. Is this normal?
Batteries are brand new from Ford. I didn't notice the battery voltage. Truck seems to run great to me, but this is my first 6.0. I also got DTC's for all 8 injectors saying Injector Circuit Low.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Rough Idle And Low ICP Voltage
My truck is a 2005 f350 6.0, all stock except for an egr delete and 4 inch cat back exhaust. I recently did an oil cooler replacement and egr delete, resealed all 8 injectors, and fixed some wire chaffing at the FICM. it's running great with the exception of idling. It seems like it's idling low but the gauge stays at 750. If I hit the high idle switch, it does fine. Red lights are stressful because it shakes and sounds like it's going to die but never does. I'm posting screenshots of my Torque pro.
I have a SC2 as well but I honestly like Torque better so that's what I use most. I know my ICP is low, but 8 don't know why. No oil in the connector, and no change when I unplug it. The ICP sensor may be a month old with 1000 miles on it. This was taken at a hot startup, sitting in park. When i say hot, I mean I had driven about 60 miles. This is sitting still in drive. ICP voltage finally climbs over 1.0 when i get going about 15mph at around 1250 rpm. The second pic the ICPV is actually higher than normal. It usually stays at .8 until I give it gas.
Ford 6.0L Power Stroke Diesel :: ICP Voltage To Jump Around A Lot At Idle Or While Cruising Or Accelerating
Just a quick question but is it normal for the ICP voltage (ICV) to jump around a lot at idle or while cruising or accelerating? Started watching this pid and not sure what's normal and what's not.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 E450 - Low Voltage On Gauge With Good Battery - No Start Condition
2000 Ford 7.3 E450 120,000 miles...
I have changed the CPS twice
I have checked the resistance of the injectors at the IDM connector with a volt meter and the harness reports back good.
The truck will run with ether for a few seconds
I have changed the fuel filter.
The fuel bowl fills quickly
I have unplugged the ICP.
The truck is showing low voltage on the gauge with a good battery. Around 10v
I have connected my 200amp car starter and I never see over 10v. I plan to check the grounds, but I am at a loss.
Everything is difficult because this is a van body so space is limited. I have also plugged in the block heater for an hour and that hasn't made any difference. Where can I get the best price on an AE scanner.
Ford 7.3L Power Stroke (1999-2003) :: Battery Light On / Voltage Meter Only Show Barely 12 Volts At Full Throttle
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
Ford 6.0L Power Stroke Diesel :: 2006 F350 - High Voltage Blanks Instrument Cluster
Got in my 06 F350 dually 2 weeks ago and after start up had no instrument indications. Truck ran great, flat line on panel. Tow haul light out also. Drove it for appx 5 miles, shazam all start working and then they cycled on and off for a while. After 10 miles, came on solid. Happened again at a later date.
Here's what I discovered. I noticed high voltage on my Scangage II. As in 16.2VDC. Monitored it coming back from a hunt. 14.9-15.5VDC. Would blank out only after hitting 16.2VDC. I'm suspecting there might be a cutout to protect the instrument cluster from damage.
Installed a new alternator on Friday the 13th. Drove home this weekend, 4 hours and no problems. Hopefully didn't boil off the batteries. Now 13.5-13.9VDC ... Just something to be aware of!!
Ford 6.0L Power Stroke Diesel :: 2004 - Battery Cranking Amps - Replace Both Battery?
I have an 04 f250 diesel and i am wondering whatst are the minimum cca's i need to be able start my truck. Both of my batteries are no good anymore and i need to replace them both but not sure on the cca's the truck needs
View 4 Replies