Ford 6.0L Power Stroke Diesel :: FICM Code / Low Voltage
I replaced injector couple weeks ago. I hooked up to livelink thru sct because it was throwing a low voltage for ficm code. It is staying at 48 volts tho. I don't see any voltage from my glow plug relay, and I have a low voltage for my egr valve. Is it just bad luck that everything broke at once or is there a fuse or a connector that I forgot to plug in.
View 10 RepliesFord 6.0L Power Stroke Diesel :: FICM Going Out - Voltage Dropping
I'm afraid my FICM is on its way out. I'm getting voltages dropping to 46.5V about once a minute. Never goes below that. Then it'll bounce up to around 48.5. It gets low when I have to rev up and always coincides with the main voltage dropping to around 12.9V.
Now for my battery condition. They are about a year old. I think I have one with a bad cell. They'll drop into the low 11V range while cranking after glow plug light goes off. While driving, the main voltage never gets below 13.1 except for very short periods ... which coincide with the 46.5V output on the FICM. Gonna have them tested separately at advanced auto and see on has a bad cell.
So, is my FICM starting to go? Second question. What do I tell the folks at Advanced Auto about replacing both an not just one? I suspect they'll want to argue about it with me.
Ford 6.0L Power Stroke Diesel :: Low FICM Voltage At Cold Start
So I am getting low FICM volts at cold start. The FICM will start at 46v and eventually drop below to 42v, but when I start to drive the truck the FICM volts go back up to 47.5, and my battery voltage goes back up to 13.8 to 14.1.
I am pretty sure my alternator is doing its job.
I left my truck sit for 2 or 3 weeks with out starting her or putting a battery tender on it, this was about two weeks ago. I have not had this problem before. Sounds to me like the batteries need a charge.
My batteries back up to full charge. I plan on letting the truck sit over night with a charger hooked to it.
Ford 6.0L Power Stroke Diesel :: FICM Voltage Drops Ar Higher Speeds
At idle it stays at 48.5v-47.5v But as I pick up speed it continually drops. At 70mph it gets as low as 29v. But will go back up slowly as I let off the throttle.
View 8 RepliesFord 6.0L Power Stroke Diesel :: FICM Voltage Drops To 40 On Cold Mornings
I've noticed on mornings when it's around freezing or colder my FICM voltage drops down to around 40. after about a minute it creeps up until it's in normal range, about 48 volts or better. This only seems to last about a minute before it's in normal range. No check engine lights though.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Low FICM Voltage Under Acceleration?
Pulled the trigger today and bought a 2004 F350 DRW King Ranch with 200000 miles. Using Forscan Lite on my iPhone, KOEO FICM voltage was right at 48. During start it went up a bit. While out for my highway road test for EOT/ECT differential (never went above 10 degrees).
I noticed that the FICM voltage would drop to the bottom of the Forscan scale (40 volts) when I was accelerating and then go back to 47.5 when I reached my cruising speed. Is this normal?
Batteries are brand new from Ford. I didn't notice the battery voltage. Truck seems to run great to me, but this is my first 6.0. I also got DTC's for all 8 injectors saying Injector Circuit Low.
Ford 6.0L Power Stroke Diesel :: Power Loss - Died - FICM?
So, I was on a road trip to Arkansa from Missouri when my truck started loosing power and eventually just died. After I tore through some stuff, I realized the ficm was just floating around off the brackets and even better yet, missing the top cap where you voltage test. And to my great luck, there was a small coolant leak that dripped it's way right into it.. So now I'm looking at replacements and it looks like I'm going to go with the Bulletproof Diesel ficm. But my question is, can I just swap them out and go.? My truck is tuned with an SCT tuner and was tuned up when it died. Should I tune it back to stock before I put a new one in or put the new one in and then put it stock and retune it after that.? Or is it more complicated than that and I should just let my mechanic deal with it.?
View 12 RepliesFord 6.0L Power Stroke Diesel :: Power Loss After Cold Start - FICM Failing?
I just bought a new to me, 2005 ford f-350 6.0L turbo diesel with 220,000 miles. It has an EGR delete, and aftermarket intake and exhaust. I am having power loss issues, and cold start issues, and judging from these symptoms, I figured it was the FICM. I thought it had to be the FICM. As per the tech folder on this site, I tested the FICM. I first learned that I have one of the Bullet proof FICM's, and when I tested it (3 times) it read between 57.5 and 58V. I conducted this test three times both with just turning the key, and with the truck running. I then took the truck into Ford, and they gave me a list of all of the codes the truck threw:
P0611
p0113
p0405
p0671
p0673
p0675
p0677
p0341
I researched all of these codes, and it seems to point to the FICM, but Ford stated they pulled a reading of 54.5v. The tech then told me that the upgraded bullet proof FICM probably ruined my injectors, because my injectors we not upgraded. Is this True?
Even though my FICM is above the low limit for voltage, can it still be going out? I am taking the truck in to have the batteries load tested, so I will know if they are contributing to my FICM failing.
Ford 6.0L Power Stroke Diesel :: Truck Would Not Start And Threw FICM Codes
My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?
View 12 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Sudden Power Loss - Cylinder 5 Dropped
My 2011 6.7 suddenly lost power, started making noise and then stalled out.
After finding out that there are zero 24 hour service companies available in the LA area, I was able to get it towed to the local Ford dealer.the next day they told me it had dropped the #5 cylinder and that they would have to tear into it to find out what happened.
While I realize that any thoughts on the situation would be primarily idle speculation, what would cause this to happen at only 125,000 miles.
Ford 6.7L Power Stroke Diesel :: 2011 - Power Loss - No Boost And Codes?
Truck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
Ford 6.0L Power Stroke Diesel :: Check Engine Light Codes P0405 And P0404 - Hesitation And Loss Of Power
I have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
Ford 6.0L Power Stroke Diesel :: 2006 - Cylinder 2 Misfire?
I have a 06 f250 with 135k that I keep getting a #2 contribution code. Power balance shows cylinder 2 low as well. No circuit codes and everything sounds good on a buzz test. Valvetrain is actuating as expected. I changed all 8 injectors w/ motorcraft with no luck. I get over 300 psi on a compression test ( 175 psi on 1st stroke then maxed my gauge on the 2nd). It smokes until I disable cylinder 2 then it pretty much clears up. I did notice I could move the top of the valve stems about 1/16", this seems really sloppy. Very little blow by and the oil cap stays on up side down until it rattles off. Any other 8 deal other than pulling the heads? I just bought this truck and have little history on it.
View 12 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Cylinder 5 Misfire Code P2285
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
Ford 6.0L Power Stroke Diesel :: CEL On For Multiple Codes - Cylinder 1 / 2 / 7 And 8 Have Glow Plug Circuit Open
Just got back from the beach yesterday. On the way back I noticed the check engine light on and read the codes. It listed 4 codes, P0671,P0672, P0677 and P0678. From what I can find, Cylinder 1, 2, 7 and 8 have the glow plug circuit open. Truck ran fine and didn't miss a beat. Ambient temp was around 80 when we started up the truck so I guess diesel plugs are not to crucial for that temp. I did notice when driving back the Vbatt would jump from 12.2v at1854 RPM (34 MPH) and 13.8v at 1652 (57 MPH).
Would bad batteries or low batteries cause this type of problem? This may be wishful thinking on my part. I have tested the batts with a DMM and they are at 12.3v. I took them out and charged them but they always go down to 12.3v. FMP is 47.5v to 48.5v. It seems suspect that all four glow plugs would be bad so I assume it could be the harness. What are some ways I can test to verify where the problems come from.First thing I would do is get two new batteries as these are still under warranty.
Ford F-150 (2004-2008) :: Loss Of Power - Code P0306 / Misfire On Cylinder 6
Having 3 new codes coming up. P0306-misfire on cylinder 6, p0158, p2272. Use my truck as a daily driver for work. Driving along before 80km/h is not to bad but can still feel a little loss of power. If i step down on gas the truck has no power and sounds like maybe cat converter is plugged. If truck is pushed to limit she will make it to her 4000 rpm and will change her gears. So i'm just glad its not tranny.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Jerk When Going Down The Road / FICM Going Bad?
If my ficm is going bad will it cause it to jerk going down the road and spit and spudder going down the road..sounds like injector but it aint smoking at all.. I think there;s a recall for the ficm for my truck too.. f250 2004 6.0....
View 3 RepliesFord 6.0L Power Stroke Diesel :: Crank / No Start - Bad FICM
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
Ford 6.0L Power Stroke Diesel :: FICM Has Been Dropping To 44v Occasionally
My ficm has been dropping to 44v occasionally so I have ordered a 270a alternator from Ed at ficm repair along with the complete battery cable kit. I also took ends advice and bought two new odyssey 65 series batteries. I went with bpd 6phase ficm though because I like the idea of the extra phases to share the load and back up the 4 primaries. I am also doing the blue spring upgrade while under the hood as well.
So my question is this.... My truck is bone stock no mod 53k mi. The bpd ficm can be set to 48,53 or 58 v. I do not see the need to do 58v but have seen a lot of guys doing the 53v option. What is the advantage of 53v? I know if you run 220 thru a 120v light bulb it will burn bright as hell for a little bit till it blows, is this the case with running a higher voltage ficm? Will it eventually wipe out injectors? Or even the ficm processor board? Should I just stay at 48v setting?