Ford 6.0L Power Stroke Diesel :: Long Cranking Time When Sitting For Over 5 Hours
2005 Ex with 6.0. It has been bulletproofed. But has had a long crank after sitting for over 5 hours. I was starting to think glowplugs but no codes, Then thinking FICM, nope voltage has always been good. After I run the truck for a few miles if I kill it. It would crank right up. No issues. Only happened after it sat for awhile. I knew it had to do with HPOP system since it took about 5 to 8 seconds to show over 500PSI.
The passenger side does not have a leak since the oil is to the top of ICP sensor. When I was going to remove it. So I took off the drivers side. I inspected the dummy plug. No issues there "they are the 12mm with teflon plugs" I inspected the stand pipe. No issues there either. I inspected the small test port on the top of the rail. No issues there either. So I decided to air test it. So I used my auto-ingenuity to close the IPR valve after I heard all the oil blow out.
Then after sitting with 120 psi of air for about 10 minutes. I hear a bubbling sound coming from the Drivers side Rail. It was a plug I have never seen mentioned here. It is at the back of the rail. I removed it and sure enough the oring is split in 2. I went to ford and picked up a new Oring it was like $4. It also looks like its a different material. I am still in the process of putting the truck back together so i have not started it back up. But I am pretty sure this was my problem.
Ford 6.7L Power Stroke Diesel :: Smells Like Engine On Fire?
Drove 40 miles took half hour then back in the truck and drove to lunch. When I got out of the truck you could smell burning. Opened the hood but there was nothing to see. Coolant level in the plastic hold tank good checked oil level, okay. No sign of smoke but the smell was real. Went in had lunch and came out and nothing. no smell nothing. Drove fifty miles home and nothing every thing working perfect and no smell. Oil temp. 197 to 203 all the way home.
Only thing that was done on truck was last Tuesday Ford did oil change.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Engine Won't Fire Up
So I've had my 2003 F-250 power stroke 6.0 for over a year now and replaced the oil with AMS oil which is good for 50,000 miles to a year as well as the oil filter which is guaranteed the same thing. I've only put 5,000 miles on it since I've owned it and made sure to let the engine heat up before going anywhere as well. Recently my engine bogged down and then had problems starting I was able to limp the last 2 miles to work but haven't been able to get it running since.
I replaced the camshaft position sensor and it fired up but once it was running it the rpm gauge dropped below 1000 RPMs it would stall out. Before it didn't have any smoke coming from the engine compartment however now when it starts it does. Is this because there's oil the possibly leaked onto something or fuel? What do I or should I look at to get it fixed?
Ford 6.0L Power Stroke Diesel :: Transmission Average Temperature?
What is the average temp the transmission runs at? Wondering because it slipped the other day and the fluid smelt like it was burnt almost. Wanting to monitor it on my scan gauge and just try to ride it out as long as possible..
View 14 RepliesFord 6.0L Power Stroke Diesel :: New Injectors - Now Truck Takes Almost Two Seconds Of Cranking To Start Engine
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - How To Reset Average MPG Calculator
I have a 2003 F250 4X4 PSD. How do I reset the "Average MPG" calculator? I asked because I have doubts that it is functioning properly.
Example:
Zero load, high-way driving.... the display shows 14.4mpg.
Zero load, in-town driving... the display shows 14.mpg.
1,000 lbs in the truck, pulling 4,000 lbs on the high-way for 600 miles (each way)..... the display shows 14.2mpg.
And since I've returned from the trip mentioned above with the 5K of load, it has not changed from displaying 14.2mpg.... even though I am back to high-way driving with zero load... been through 6 -8 tanks of fuel.
My expectation is that when I am traveling without a load on the high-way that it should get the best MPG. Subsequently, when I am pulling a load, utilizing the "Tow" function (without engaging O/D), that it would get worse MPG. However, it appears there is virtually no difference registered / displayed in MPG regardless of how I drive or what I tow.
Ford 7.3L Power Stroke (1999-2003) :: F250 Cranking For A Bit Of Time And Refuses To Start
I have a 1999 f250 7.3 psd. it cranks and will not start, it use to crank for a bit of time and then start and now it refuses to start. If I leave the key in start position for like 30 seconds it use start and now it wont. I am thinking it is something with the glow plugs?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Slower Cranking Time And Took A Second Or 2 Longer Than Normal
I have a 2002 F350 7.3 with 76,000 miles (still a baby) ... about a week or 2 ago i got in my truck and went to start it like normal, except instead of whipping over and firing right up in the snap of a finger, it kinda had a slower cranking time and took a second or 2 longer than normal. My first thought was maybe the battery's, BUT there basically brand new !!! not even a year old !!! ... so i figured maybe a starter, but i just left it as is, it still ran normal after firing.... Until this morning, I went to go start it and it cranked over 3 or 4 times real slow and would crank any more, it did this to me multiple times. Its acting like dead batteries so i put a jump pack on it, no change. I am thinking maybe a starter ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Engine Service Light Stays On All The Time
my 2003 f-250 4x4 6.0 engine service light stays on all the time (for about 2 weeks now) it has 33,323 miles on it. it is running fine-no problems yet. no codes are showing up on a diagnostic test. What is going on?
View 10 RepliesFord 6.0L Power Stroke Diesel :: Starter RPM When Cranking?
I've been trying to figure out a slow start condition on my 06 F350. What should the starter rpms be when cranking? My scanguage reads 180. Does this sound low? Batteries are new.
View 9 RepliesFord 6.7L Power Stroke Diesel :: Cranking With No Fuel?
Cranking without fuel is probably never a great idea - but it happens - maybe after repair or when someone runs out of fuel, etc....
Is it any harder (worse than usual) on these Bosch fuel pumps than any other vehicle? I realize that the closer tolerances and the very high pressure might make things a little more fragile in a "no fuel" situation...
This question came from a discussion that I was in (maybe beer was involved) a couple of days ago... Of course we had 4 different opinions... I would like to know the facts - if someone is more qualified then us "redneck mechanics"
Ford 6.0L Power Stroke Diesel :: 2004 F250 Cranks But Won't Fire
I just bought an 04 Ford F250 diesel 6.0 with 92k miles. Previous owner installed a UNGO alarm with remote start. Last week, after work, I started it using remote start. I got in the truck and realized I had forgotten something, so I exit the truck and leave the keys on the seat. Truck is still running. The doors lock. I reached in through the cracked window and pushed the unlock button. Here's the problem.. the truck died immediately won't start.. mechanic says it's the high pressure oil pump. I'm thinking it's the anti theft system but no luck.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Won't Start - Voltage From 11.5 To 10.5 While Cranking?
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Cranking But Barely Tries To Start
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
Ford 6.0L Power Stroke Diesel :: 2006 - Truck Cranks Over Fine But Does Not Fire
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Long Crank And No Fire / Startup
OK here we go it all started with a long crank and now no fire. I changed cam sensor wiggled wires got to fire , shut off than nothing . Changed wire from cam sensor to about 6" from ecu found small nick in wire. Swapped ecu no good... I am getting my numbers from torque app.
ficm sync = 0
RPm = 172
FLP = 12
fmp =49
Hpop = 1823 max
Ipr = 80.9 max stready at 48
ipr volt =.02 at rest
Also tested fuel pressure at filter 80 psi ( blue spring)
ficm sent to ficm repair, tested good
cam sensor changed , pig tail also
bubble test on fuel filter no thing there
So any thing else to check or am i looking at a harness change?
Ford 6.0L Power Stroke Diesel :: 2005 E350 - No Hot Start / Just Cranks But Won't Fire Up
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Truck Turns Over Just Fine But Won't Fire With Codes
Got up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start / No Cranking
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 Replies