Ford 6.7L Power Stroke Diesel :: When Cold Diesel Engine Sound Intermittently?
It only happens on a very Rare occasion.
When Cold, and when I start out as I open the throttle, it suddenly sounds like there is not a piece of quieting stuff on the engine. I mean its like I can hear right into the engine itself.
I back off, It goes away then I dont hear it again for another Month or two.
Ford 6.0L Power Stroke Diesel :: Cold Start / Put Into Gear And It Stalls
2007 F350 138,000 miles
I'm having a small problem. For the past couple of weeks I've started the truck in the morning. I let it run for a few min's as I always do. I jump in it an put into gear and it stalls. Put back in Park , starts right up and then is fine.
knowing that the EGR is due for its monthly cleaning, I went ahead this time around and got a new one for it. Same thing this morning.
I think its kinda odd that it stalls that one time and then is fine. I do run a scan gauge in the truck as well.
Ford 6.0L Power Stroke Diesel :: F250 - Cold Starts Fine / Stalls Immediately After / No Throttle Low RPM
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
Ford 6.0L Power Stroke Diesel :: 2007 - Oil In Coolant Reservoir - Getting CEL Intermittently?
Have been working on military diesels for years. I have a 2007 Ford F-250 6.0. I am currently waiting for a new oil cooler as I have oil coming from my coolant reservoir and no coolant in my crank. My question is I have been having my engine light coming on and off intermittently since deleting my EGR cooler.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2007 - Won't Start Intermittently - Running Slightly Rough
I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Overheating When It Is Cold Outside
I just bought a used 2007 f250 with the 6.0 power stroke. The truck has approx. 160,000 miles on it. He is having a issue with the truck overheating when it is cold out. When the air temp is above 30 degrees or so, he doesn't have a issue. So,my he overheating only occurs when driving down the highway in low temperatures. It can idle in the cold fine.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2007 - Hesitates At Start Up When Cold?
07 6L gave me a fit the other morning. I spent the night in the mountains Saturday night. Sunday morning was -5. With no place to plug in the block heater. When I started it it bucked and hawed and didn't want to run... It keep surging for a while and finally smoothed out after about 3 mins... Is there an additive that will work for this for the times there is no place to plug in? Oil additive or fuel additive?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 Very Rough Idle When Cold
I have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean .... It's 98* on a cool day , when "cold" I mean just started for many hours.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2007 F350 DRW - Cold Start Hesitation No DTC / CEL
Recently I replaced the unison ring on my turbo, EBP sensor and cleaned carbon out EBP tube/upper part of motor. After doing so she seemed to run fine but not like I remember when I first got her. Plenty of power but ever so slightly off, only an owner would notice. Few weeks later she hesitates a little bit while she's cold in the morning. I let her run 3-5 minutes b4 actually driving but as u know it's a little while to get up to operating temp. Temps seem OK 190-200 EOT/ECT. Fresh oil/filter, air filter, coolant, EGR was cleaned out a little while back and EGR valve replaced 25k ago. I'm not sure where to look at this point...the motor has about 30k on it.
View 3 RepliesFord 6.7L Power Stroke Diesel :: 2012 F250 Diesel Frequently Stalls Momentarily After Touch The Brake
My 2012 diesel frequently stalls momentarily after I touch the brake. This is very annoying as I drive in heavy traffic and often have to touch the brake then accelerate to merge into freeway traffic. The dealer service department said this was a 'feature' and not a flaw. Is there any way to eliminate this issue?
View 5 RepliesFord 6.0L Power Stroke Diesel :: Stalls While Driving
Driving down the road at 55, the truck just stalled out and won't restart. This has happened before but it always started back up right away. Put a scan tool on it last week and it's giving me an injector 1 low pressure, and egr.
I've read that running the truck at low voltage could fry the FICM and cause all sorts or problems. I just replaced the alternator this week because the batteries always drained while the truck was sitting.
Ford 6.0L Power Stroke Diesel :: Runs For A Few Seconds And Stalls
My truck started fine my truck was running good. One morning while working from a hotel I went to start it in the morning and it started and stalled more than a few times but eventually ran fine later it did the same thing. The next morning it would not crank at all. I deduced it was the ficm and ordered a replacement the dash was acting funny and tach dropped before it died. I ran the. Test on the dash it swooped the gauges acted fine. I checked and wiggled sensors wires. I also checked were a splice at the crank sensor was it looked good then I bought a meter and the ficm seemed to have the correct volts it was a upgrade. Had 57volts at 1 screw koeo and while cranking.
PCM and replacing the crank and cam sensors. I don't really think it is the harness it will now crank and shut off crank and shut off like it did at first. He said it's stalling because it looses ficm sink. I haven't put new ficm on it ...the harness was allot better than the first. Could the crank sensor splice be wrong it is done its soldered together and heat shrink ... is it the ficm or the dash. I'm out of my comfort level I was also reading it only needs ficm sink to start. Not run. In addition #2 injector is throwing a code. I asked him if he thought the fuel was getting pressurized and his reply was the fuel has nothing to do with ficm sink. Also, I swapped relay out with my other 6.0. And its running fine This is everything I got ....
Ford 6.7L Power Stroke Diesel :: 2011 F350 - Lost Power Intermittently?
Currently truck is in the shop after having multiple episodes where it lost power. It has 47,000 miles on it. When pushing down gas pedal, just does not want to go. Very slow to shift through the gears and get to highway speed. Turbo was not there, and there was also a hard shift/jerking from 2nd - 3rd. Did notice the traction control sensor kick on a couple of times....which was just replaced since a hole rubbed through the wiring. (took it to Ford twice before they found the problem)
They told me today that the code generator said to look at wiring but they did not find anything (heard that before) and that the fuel is possibly contaminated with DEF. If that is the case, someone is messing with my truck! What I don't understand that if the DEF does turn out to be in the fuel tank, wouldn't we have the problem continuously and not intermittently over a month after driving thousands of miles and going through numerous tanks of fuel? We drive and average of 60 miles per day just for work, half interstate/city.
Ford 6.0L Power Stroke Diesel :: ABS Light On Intermittently?
My ABS light keeps coming on randomly. Sometimes it's on for a full day sometimes a few seconds. It's pretty weird because it doesn't throw a code or anything. Where to go from here.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Engine Stalls Once Warmed Up
I have 2005 Ford 6.0 turbo diesel. I replaced high pressure oil pump because it would die once it warmed up. Also replaced high pressure fuel rails and icp solenoid. Engine still dies when ect reaches 204 and eot reaches 235. Why it still dies?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Stalls When Warm Then Restart
My 6.0 stalls when its warm and it restarts no problem. no codes are given with scan gauge. No changes on icp or ipr when it happens. At idle icp ranges 577 to 737, fmp 47.5 to 48v, ipr 23 to 28, map 14.9, tfc .32. all at idle. all increase when rpm goes up. ive done the d plugs, sct plug ficm replaced 2 yrs ago. done egr delete, need to trouble shoot? Again no codes given...
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Run Rough And Stalls Eventually?
I have '03 6.0 when it gets to full temp it will run horrible and eventually stall. It will take a few long cranks to restart. will drive a little bit but will stall again. It will idle all day long even after a stall. IPR @hot idle is 22 and ICP @hot idle is 640. IPR and IPC readings seem to run good throughout the rpm range except for when it dies. Then the IPR is anywhere from 71 to 85. Has new ICP and Pigtail. Runs very good until hot. I am leaning towards HPOP.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure Dropping Above Idle / Stalls Out As Soon As Try To Accelerate
Ok here is the back story over the last couple months with this late build 04 6.0 with 230,xxx miles. I had problems with it losing oil pressure at idle, which lead me to replace the hpop. After that repair the truck still wouldn't run right so i had it taken to my local shop for some diagnostics. They fixed a few electrical issues and got it running, also telling my I had 2 injectors on the way out. Due to expenses I replaced only the 2 injectors in my driveway. A few days later the ipr screen got plugged and failed. Replaced that, and changed the oil, and it ran for a week.
Now for this weeks problems. Yesterday the truck lost all power and stalled out on my wife. She pulled the codes while I was at work and this is what was listed
P0404-60===
Code: P0404 - EGR valve position control performance or range fault
P0405-60===
Code: P0405 - EGR Sensor A Circuit Low
P1335-60===
Code: P1335 - EGR Position Sensor Minimum Stop Performance
P2290-60===
Code: P2290 - ICP Too Low
Using forscan she forced the IPR 80% open and the truck would start but as soon as you try to accelerate it stalls out. Today i got the truck to start the same way. While idling the IPR was at 44% and I had about 870 psi at the icp. As soon as i would throttle up the icp would drop to around 400.
The hpop i put in a couple months ago is covered under a 1 year warranty and that's what I am leaning towards because of the plugged ipr last week. I waned to see what the great minds hear thought as well.
Ford 6.7L Power Stroke Diesel :: 2011 - Won't Crank Intermittently?
I have a 2011 F250 w/6.7 Powerstroke. Love it. In September I came out of work, turn the key to on position...no glow plug indicator light, no high pitch whine of the fuel pump and most importantly, it won't crank. Gauges all light up, but no glow indicator, no fuel pump sound and no crank. Get towed to dealer. Next morning they try it, and it starts right up. They can't get it to fail. Sent me home with no trouble found.
A few weeks later, same condition in my garage. I had thought that maybe there was some sort of safety switch that perhaps thought it wasn't in park. I put in neutral, roll back about 6 inches, glow plugs light, fires right up. Now I think I'm on to something. In the last 2 weeks, it happened 2 more times, and both times I'm able to get it to light up by rolling a couple inches. Then, last night, same problem, but parked against a curb. Try to push up hill, but no luck.
Have to get towed to dealer again. Tow truck drops at dealer, and because I knew it would, I tried to start, and it worked. Dealer called me, says they can't get it to fail (again), but found one battery was "bad". I'm not really buying the battery story, but also understand the dealer having trouble figuring out what is wrong when nothing goes wrong for them.