Ford 6.0L Power Stroke Diesel :: 2005 F350 - Rough Idle And Low ICP Voltage

My truck is a 2005 f350 6.0, all stock except for an egr delete and 4 inch cat back exhaust. I recently did an oil cooler replacement and egr delete, resealed all 8 injectors, and fixed some wire chaffing at the FICM. it's running great with the exception of idling. It seems like it's idling low but the gauge stays at 750. If I hit the high idle switch, it does fine. Red lights are stressful because it shakes and sounds like it's going to die but never does. I'm posting screenshots of my Torque pro.

I have a SC2 as well but I honestly like Torque better so that's what I use most. I know my ICP is low, but 8 don't know why. No oil in the connector, and no change when I unplug it. The ICP sensor may be a month old with 1000 miles on it. This was taken at a hot startup, sitting in park. When i say hot, I mean I had driven about 60 miles. This is sitting still in drive. ICP voltage finally climbs over 1.0 when i get going about 15mph at around 1250 rpm. The second pic the ICPV is actually higher than normal. It usually stays at .8 until I give it gas.

View 5 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 - Starts When Cold But Not When Hot

I just bought an 05 F350 and it starts fine when cold but after I drive it a while will not start even after sitting for up to an hour (overnight cold start fires right up). I replaced 1 battery and alternator and it started up right after install but after driving for a while still have the problem - cranks fine but will not start.

Buddy of mine has the same truck (just a 250) and had this same problem recently and had to replace the High Pressure Oil Pump, which was super expensive! This is my first diesel truck and it runs like a champ (once it starts!)

View 1 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 - Engine Starts After Clicking Sound When Crank For Few Seconds

I am lost on what I need to do with my 2005 6.0. Last summer it started giving me trouble once in a while starting. I turn the key on and wait for the wait to start light to go out. When it goes out, turn the key and it starts, most of the time. Last summer I went to start it the same way, only it cranked and did not start. I turned the key off, back on and cycled the wait to start light again and turned to the start position, it started right up. Whenever it would act up I just turn the key off then back on and it starts right up. Usually on the second try, but lately it has taken 3 or more tries. I am not finding any real pattern to when it wont start.

When it does not start I can crank on the starter until the battery dies and it wont even think about starting. Turn the key off and back on, it will start.
Another thing I have noticed, when I crank the engine I can hear a clicking from under the hood right before it starts. I think it must have something to do with the injectors. I will crank the engine a few seconds, hear the clicking then it starts. If I don't hear the clicking it will not start, so when it doesn't want to start I also do not hear the clicking sound.

The other day I started it, drove 5 or 6 blocks and shut it off. After 20 minutes or so went to leave. I had to cycle the key 4 or 5 times off and back on before it decided to start. It is getting worse, doing it more frequently, and taking several times of key off and back on to get it going. Where should I start looking to find this problem?

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 - Lag Off Idle For About A Second Every Once In A While

Well, after getting the bed back on my '05 F350, I have been driving it on the road for a few days, but now I have a new problem.

Every once in awhile I get lag off idle for about a second, then the turbo spools and everything is fine. Other times, I step on the accelerator a bit from a stop, and the truck acts like its going to die for a moment, a puff of black smoke, and then the turbo spools and all is back to normal. It a combination of these two problems happens about 3-5 times out of 50 stops a day.

I have a scanguage and everything looks normal and I never get any codes when I check.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 Running Rough - No Power To Move

I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.

So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .

View 7 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 - Hesitates / Low Power Driving / Idle

I have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.

I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.

All of this was done at the same time at just under 4,000 engine hours:

1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt

After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",

Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.

Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.

After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.

So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.

After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.

OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2

While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.

View 9 Replies

Ford 6.0L Power Stroke Diesel :: 2003 F350 - Rough Idle / Cylinder 4 And 5 Contribution Balance Code

2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.

Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.

So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.

Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?

View 7 Replies

Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - No Power - Black Smoke?

05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.

This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....

Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.

However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine

Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.

View 5 Replies

Ford 6.0L Power Stroke Diesel :: 2005 / E350 Van - Rough Idle Stalls / Hard To Start

Rough idle I have had for little bit.Would stall out at idle or a stop, but fire right up? No one could figure it out with the stalling, but now its bad, started yesterday. Have white/blueish smoke sometimes, ( white smoke smells fuel) on restart after warmed when it dies, first time it took 25 mins to restart, now only takes 5 to 15 mins, when I step on it INCREDIBLE full power, fuel mileage gone to hell also since yesterday. Had full tank, now 1/2 tank.

No problems on cold start at all, no check light, 325,000 and never had this before.

Bad fuel?
ICP?
FICM?

Recent work, new turbo, ( turbo was original turbo installed when built) cooling line to waterpump, oil change, new fuel filters, front brakes and 2 new batteries.

View 5 Replies

Ford 6.0L Power Stroke Diesel :: 2005 - Rough Idle - Codes P0672 / P0674 / P0678

I have a 2005 f350 6.0 power stroke. I had a crank no start when hot issue. I bought an obd scanner with the torque app. IPR was at 85%. ICP pressure was low. I got the IPR out and bought a new screen because it was clogged. Upon putting in I broke the injector female side plastic connection.I bought the injector connector piece and installed it. After putting everything back together it starts but runs very rough,low power. The IPR was fixed. ICP,ipr and ficm are at good levels now.

IPR=14.7%-30%
Fcim sync=1.0
Fcim voltage=48.5
ICP pressure (idle)650-850psi

My fault codes are:

P0672 (glowplug)
P0674 (glowplug)
P0678 (glowplug).

Why it would be running/idle rough?

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2007 F350 Cranks Over Longer Before It Starts

Lately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .

View 7 Replies

Ford 6.0L Power Stroke Diesel :: 2004 F350 - Starts Very Reliably But Stalls Within 1 - 2 Seconds

I have a PS 6.0 in my '04F350 that starts very reliably but stalls within 1-2 seconds. Restarts after cranking for 5-30 seconds. This only occurs if the truck sits for more than 6 hours. The longer the truck sits, the longer it has to crank to restart. Also if the tank is full and the truck is parked pointing down hill this does not occur, if it is parked pointing up hill it occurs even with a full tank. Shows no codes. I've had several mechanics look at it and no one has been able to explain or propose a solution expect for wholesale replacement of parts. The symptoms indicate to me that air is getting into the fuel system but I'm not sure where to look.

View 10 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power

I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Rough Idle Sometimes

I have a 2000 F350 4x4 CC 7.3L 323,000 miles auto trans. I have removed my tuner just to make sure that it was not the issue. The truck will run fine then all of a sudden the idle will rise then fall or shudder or go up and down and sometimes it will just Die but it always restarts. No trouble lights at all. I am not sure what is causing the issue?

View 6 Replies

Ford 6.7L Power Stroke Diesel :: 2011 F350 - Losing Power - Rough Noise - Vibrating?

2011 F350 diesel with 10,000 miles. I have been experiencing problems with the truck loosing power, making rough running noise (pinging like an older diesel), and vibrating. As though the motor is bogging down. It usually occurs on small inclines or hills with the truck in higher gears and low rpms. It will also occur running on flat ground 65-70 mph. Had it occur once while turning the truck around in 1st gear and low rpms. Depressing the accelerator will bring the truck out of it.

This problem occurs randomly sometimes a couple of times a week to not at all. Took to dealer and they found no codes and of couse it didn't do it on the hour long test drive I took the mechanic on. However they did say they had two other owners come in with the same complaints, but could not get trucks to repeat the issue. Problem usually occurs in the hotter part of the day, maybe just coincidence. I had seen similar posts with this problem but no conclusions.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: F350 - Surging And Rough Idle While Driving

I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.

I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.

A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.

I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.

They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2004 - Black Smoke When Starts To Idle

I have a 2004 f250 i purchased a month ago. Its been cold in Denver this last month which is why I didn't mind it much. But now that its been in the 70s im concerned. Its always the first start up that it acts up. I go to turn the truck on and it starts idling for only a sec or two, then shuts off. I crank it about 3-4 times before it actually comes on and stays on. There is black smoke not white smoke once it starts to idle. Once idling it stays on and drives the way it should. If i try to start the truck again it will do so with out hesitation. I just did a tune up at grease monkey including fuel filters and oil filter. again its the first start up always.

View 1 Replies

Ford 6.0L Power Stroke Diesel :: Truck Starts / Running Rough Then Die - Fuel Draining Out Of Bowl

2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.

After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.

View 13 Replies

Ford 6.0L Power Stroke Diesel :: 2006 F350 - Bucking / Rough Running

2006 F350 6.0 ... I am piling up parts for a bulletproof party later this summer. It has gotten grumpy ahead of schedule. I will hook up the AE tomorrow for consultation.

In the meantime. Running rough at 50. Seems to accelerate from a stop semi ok. Sitting at idle, holding rpm at 1750 I hear kind of a thump under the hood and the rpm drops 300, then slowly finds it way back to 1750 and it repeats itself.

This thump has not been noticed in the past. Could this be the VGT not working as expected?

View 4 Replies