Ford 6.7L Power Stroke Diesel :: Climate Control - A/C Compressor Will Not Engage And Allow For Cooling The Cab Of Truck
Here is the issue i am having. 2011 F-350 King ranch with all bells and whistles. In Arizona now we are in the season that the weather is cold in the AM and sometimes hot enough in the late afternoon to need the A/C in the truck. with the settings on Auto which i normally do, and the external temp reading in the 80s, and the internal thermostat set at 70 or lower, the A/C compressor will not engage and allow for cooling the cab of the truck. But sometimes it will work just fine. I am assuming there is a temp sensor for cabin temperature. Where that is located. or will i have to change out the entire Climate Control Module. I would take it in to have it checked out but it is an intermittent problem, and i cant not have my truck for a couple of days while they try and figure it out.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Climate Control Not Working Properly
I have a 2005 6.0 f350 lariat... My climate control doesn't switch very well I can get it to go to floor sometimes after 15min of pressing the button. The vacuum pump is good the tank has no cracks. I feel that the system is either plugged up or has a leak. I cleaned the tank after my hub seals went and it sucked a ton of dust and dirt through my wheel bearings in to the tank. Is the vacuum switching part of the digital display? Or is there a separate part?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - No Radio Or Power Windows
I have a 2004 F250. Owned it for a little less than 4 miles (186k on the odometer) .. The other day making a routine run and the radio goes out. Stopped to check it out and found I had no power windows either.
Made it home, checked the fuse on the radio and its good and the the power window fuse is also good. Put a meter on the terminals and have no voltage going to them. What I need to look at???
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Sudden Loss Of Power
I have a 2004 F250 6.0 DuperDuty with about 170,000 miles on it, so far no major break-downs, just a starter and a blinker relay, but now I have a problem.
When I start now, the truck starts fine and it sounds fine, but it has almost no power even if I floor the gas peddle, there is a delay of like 2-3 seconds and then responds slowly, like some tractor. Eventually it starts to move slowly, and after it warms up (after a few minutes), the gas peddle responds more normal.
Also - at about 45mpg, at lower RPMs about 1250, the engine starts to shake (weird), it doesn't do it at idle about 850 RPM, or when I get it up to about 1800RPM+, but at about that 1250 RPM it does do it, luckily I driver locally for a few miles.
What could this be ? What exactly happens when I press on the gas peddle, what systems are involved and in which order?
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Sudden Loss Of Power
I've got a 2004 F250, 6.0, with 150k miles. I was pulling a motorcycle trailer uphill in the mountains when suddenly I couldn't go over 10 to 15 mph. All the gauges read good but it just couldn't get any power.
Got to the top and checked over everything. Didn't see any issues. Drove it home (200 miles) the next day. It drove okay on highway but it felt like the turbo wasn't coming on. Coolant was low and EGR was gunked up but only slightly wet. From what I read, it sounds like EGR cooler is failing but would that cause the turbo not to come on or feel like that loss of power? Reading another thread, I thought it might be the fuel pickup but I dropped the tank and the sending unit looked very good.
I'm ready to throw on a bulletproof egr cooler, oil cooler and rebuild the turbo if necessary but hate to get to the end and find out none of that worked.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - No Power And Will Not Accelerate
I have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Power Loss / Died And Now Cannot Get It Started
While driving home the other night at highway speed my truck lost power. I just filled the tank about 15 miles before then and everything was running fine. No lights came on the dash before the truck died and now can't get it started. Bad fuel? Clogged filter?
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Losing Power Then Stalled Out And Wouldn't Start
this morning I started my 2004 f250 drove a mile and filled up my truck. Then drove another mile and my truck acted like it was running out of fuel. It was loosing power then stalled out and wouldn't start. About five hours later I tried to start it again and nothing. about five hours after that I tried it again and it started up and drove fine.
My thought was fuel filter or the water trap. I haven't had a chance to open the filters up and check them yet. Today while I was at work I got on here to see if I could figure out what was wrong with it. all I could think of was maybe the HPOP went out or the ICP sensor. Could one of these be the problem or was I right with my original thinking and it's just a fuel filter? First thing in the morning I'm going to pull the filters and replace them.
Could there be something else wrong with my truck that I don't know about? Like I said I filled up the fuel tank then it lost power within a mile and stalled out and wouldn't start back up. Then about 10 hours later it fires up and acts like nothing happened.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Just Died All Of A Sudden - Intermittent Power Loss
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Slight Miss / Rough Idle / Loss Of Power
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 V8 - Hard Start / Rough Idle / Shaking - No Power When Cold
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
Ford 6.7L Power Stroke Diesel :: 2012 F250 - Stuck In Park With No Brake Lights Or Traction Control
My 2012 F250 6.7 once again (third time in 2k miles) got stuck in park with no brake lights or traction control. I found that removing the shroud from the steering wheel allowed me to manually activate the solenoid and get into gear but could only drive in manual shift mode.
Something is causing the brake switch fuse to blow. When I replace the fuse all is well for maybe 1k miles then it happens again! After the second time I replaced the brake switch thinking it was the cause but no deal. It happened a third time. The dealer who fixed it the first time could not find the cause.
This is frustrating and downright dangerous! What in the circuit could be causing the short?
Ford Wiring/Electrical :: 2007 F250 - Power Out On Cabin Temp Control Panel
Well I've had her just 1 week, used, and today I turned it on and the power is out on the A/C n Heater /Fan Control ASSY. It worked the last 900 miles from FL to OH. And today worked this morning, but 2nd time I got in the truck today there was No Lights in the Air Control Assy. I didn't get an Owners Manual, so what fuse to check.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.0L Power Stroke Diesel :: 2004 F250 6.0 - No Start With Low ICP Psi
I have an 04 6.0. My truck was running perfect, no problems. I start my truck, it started idealing rough for a couple seconds then just died. After that it just kept cranking and no start. There are no codes, tried unplugging the ICP sensor and nothing. Checked the fuel filter and its filling up with fuel before cranking. Oil is at a good level. FICM is reading 46.5-47.5 before cranking. Checked the ICP Psi I'm only building 11psi and HPOP was replaced in October.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Will Not Start At All
My husband and I purchased a 2004 f250 king ranch 6.0L... We love the truck, despite the headaches. We took it to a dealership and spent just under $5k in parts, drove it for a month (everything going great) until we shut it off to bs w a friend and it won't turn back on. It's been sitting for 4 days and nothing. Cranks and cranks, but won't actually start. We are pretty handy with gas trucks, but this diesel is out of our element- we are getting better though haha!
We looked on here and saw that the no start could be bc of the FICM - swapped it out- not the issue.
Now the codes being thrown are P2291 & P2285 (or so my husband says)
We are thinking if we replace the ICP and that fixes it, we won't need to do the HPOP. Or do we need to do it as well? Are we on the right track?
When we shut it off, it didn't have any lights on, no gauge fluctuations, or any "red flags". This is why we are stumped!!
(Ford dealership fixes: 2 batteries, new starter, new tank cap, new oil cooler, maybe a few others- receipts not infront of me).
Like I mentioned, we've already dropped more money than we have into this truck and now it's taking more- we love the truck and once it's fixed we will "have a new truck" it just sucks bc my husband works afternoons and I'm a stay at home mom with a 14mo and this is our only vehicle.
Ford 6.0L Power Stroke Diesel :: Display For Climate Controls Was Completely Black
Was driving the last week and happened to look down and notice the display for my climate controls was completely black. They were still running at whatever I had them last set at but couldn't change anything or turn the system off. Pulled into a parking lot, turned the truck off then started it again and everything was working fine.
Couple days later, was driving down the road again, glanced down and now my climate display, stereo display and odometer display were all black but once again everything was still functioning, just couldn't change anything. Turned my wipers on to check those, heard a little click, and all the displays popped back on like normal???? Wipers worked just fine too.
I'm assuming a short somewhere but wouldn't even know where to start to look or if it's even within my limited skill set to try and track down.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Crank But No Start
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Irregular EOT And ECT Readings
I have a 04 CC F250 6.0. Lately my EOT and ECT have been all over the place the ECT has been fluctuating more than the EOT. For the past 100K miles my deltas have been within the 15 degree range. The ECT will vary up to 25 degrees from the EOT; EOT may be 180 and ECT 155. I purchased a new water temp sensor thinking that was the culprit, but haven't replaced it yet. I am using a scanguageII to monitor engine parameters. I have noticed when starting the truck in the morning the temps seem to be stored from the previous night, ex. ambient temp is 75 and SGII shows 90 then comes down to match the ambient temps. For the past few days I have been noticing the truck runs and starts smoothly until I get up to 50 mph, when cold, then starts to develop a miss until it reaches operating temps. Once reaching operating temp the truck runs smooth. Could the ECT sensor cause this or is there something else going on, missing at hwy speeds until warmed up?
View 14 Replies