Ford 6.0L Power Stroke Diesel :: 2007 - Cranks But No Start - FICM / Cam / Crank Sensor No Sync
2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Crank / No Start - Bad FICM
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
Ford 6.0L Power Stroke Diesel :: 2006 F350 Not Starting / No FICM Sync
I have a 2006 F350 with around 208k mikes, automatic with a no start, 0 No FICM Sync.
The CMP and CKP has "no / 0" for synchronization and a "NO" synchronization from the FICM. Should this be "yes / 1" when trying to start?
The camshaft position sensor status indicated "yes fault".
FICM is at 48V,
DTC currently on
P2614 camshaft position signal output/open circuit - CMP
Glow plug circuit cylinder 2, 4, 5, 6 (these have been on for 12months and 1,000 miles and never had an issue starting)
B1352 - left front temperature damper motor
B1360 - left rear temperature damper motor
U1900 - CAN - communication BUS fault
I am running all OEM filters
Ford 6.0L Power Stroke Diesel :: No FICM Sync And No Fuel Pulse Width
04 6.0 with no FICM sync and no fuel pulse width. Crank/cam sync yes. All other data is good. Tried known good FICM and PCM but nothing. Had glow plug codes thats it. Found chaffed wires due to mice. Replaced damaged Injector harness still nothing. Fuel pressure is good btw.
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2005 Excursion Keeps Cranking Over / No FICM Sync
My 6.0 2005 Excursion has been running great lately except for an issue starting last week. I go to leave work and it cranks over-and keeps cranking over. I fire up the torque pro app and see that I have no FICM sync. It just reads 0. I pop the hood and fumble around the FICM connectors. Try cranking again and it cranks and cranks and finally kicks in. I have not had this happen since but am paranoid now that this will occur again in the worst possible place and listen to everyone in the family tell me to get rid of my prize and get a newer truck. I monitor quite a few things on the Torque pro app but could others chime in what I should be monitoring in the meantime to try and solve this issue.
View 4 RepliesFord 6.0L Power Stroke Diesel :: FICM Sync Taking Longer Than Usual
I've had my 6.0 for 2.5 years now and got really acquainted with what makes what noise, and how long starts took etc. recently this morning, i had a longer start, longer than a normal long start (4-5 seconds). Felt too long to me, but it started and didn't turn it off to try again. Got to my destination, turn the truck off and brough up ICP, FICM, FICM SYNC and cranked and watched.
After 1 second ICP jumped to 600 then to 770 and 2-3 seconds later FICM sync finally read 1 and it fired. What can be causing the sync to take so long? I have had intermittent no starts before, maybe 4 in the 2.5 years i've had it and every time i have pushed on the fuse blocks by the driver batteries, and also pushed on the FICM connections to make sure everything was okay. That seemed to always work.. But no amount of pushing on them are solving the long start that is happening...
Ford 6.0L Power Stroke Diesel :: Crank But No Start / Fluctuating RPM / No Sync
Truck Details:
2004 6.0 F250 extended cab.
Mileage: 1,162,000 Kilometres (the dash stopped at 999,999)
Egr is deleted.
Motor has approximately 120,000 miles on it.
The previous owner delivered campers with it. He said that almost everything in had been replaced except the transmission.
I've had an intermittent crank, no start since I've owned the truck. (2.5 years) It's only happened maybe 5 times and the second attempt was always successful....until yesterday morning.
It threw a few codes but none I believe related to the no-start. One code for a transfer case issue, one for a turbo under-boost, one for the ac clutch not communicating, one for the exhaust pressure sensor not communicating. I would list the actual code #'s but after the first scan I reset them due to my ignorance.
While cranking I get the following numbers:
FICM LPWR- 11 to 12.5 volts
FICM MPWR- 47.5 to 48.5 volts
ICP v- up to 1.8 volts
ICP pressure- up to 1493 psi
IPR %- 15 to 55%
No FICM sync
No ckp/cmp sync
RPM- 0 to 60 and fluctuating
FUELPW- 0.00 ms
I've checked hertz across the red and orange wire at the centre plug of the pcm while cranking and i believe it tested good at 1.4 hertz. The batteries are both getting old and I plan on replacing them but the voltage seems adequate.
The following Forscan tests all checked out good.
PCM KOEO
PCM KOEO injector electrical
TCM KOEO
There were a few others but I think they're irrelevant and they checked out good anyway. I've visually inspected for chaffing but I need to look harder still. There were definitely no codes regarding the cpm, ckp or ficm. Based on what I've read, the fluctuating rpm reading should point to something I'm not aware of.
Ford 6.0L Power Stroke Diesel :: Rough Idle - FICM Is At The Start Of Going Out?
So after replacing all injectors, I was getting a rough idle and drive. Got an imbalance on 5 & 4. Cleared out codes and 5 still showed. The guy doing my work and I couldn't trace it to anything so we thought well maybe we got a bad one. Did fail the buzz test. So got a warranty one and put in. Wouldn't you know it's still not running quite right. Only thing we can think of is maybe the ficm is at the start of going out. Voltage reads good still though. Staying constant at 47/48. Is more noticeable to run rough when starting from cold then smooths out but you can still make out/feel an injector going in and out.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Low FICM Voltage At Cold Start
So I am getting low FICM volts at cold start. The FICM will start at 46v and eventually drop below to 42v, but when I start to drive the truck the FICM volts go back up to 47.5, and my battery voltage goes back up to 13.8 to 14.1.
I am pretty sure my alternator is doing its job.
I left my truck sit for 2 or 3 weeks with out starting her or putting a battery tender on it, this was about two weeks ago. I have not had this problem before. Sounds to me like the batteries need a charge.
My batteries back up to full charge. I plan on letting the truck sit over night with a charger hooked to it.
Ford 6.0L Power Stroke Diesel :: Power Loss After Cold Start - FICM Failing?
I just bought a new to me, 2005 ford f-350 6.0L turbo diesel with 220,000 miles. It has an EGR delete, and aftermarket intake and exhaust. I am having power loss issues, and cold start issues, and judging from these symptoms, I figured it was the FICM. I thought it had to be the FICM. As per the tech folder on this site, I tested the FICM. I first learned that I have one of the Bullet proof FICM's, and when I tested it (3 times) it read between 57.5 and 58V. I conducted this test three times both with just turning the key, and with the truck running. I then took the truck into Ford, and they gave me a list of all of the codes the truck threw:
P0611
p0113
p0405
p0671
p0673
p0675
p0677
p0341
I researched all of these codes, and it seems to point to the FICM, but Ford stated they pulled a reading of 54.5v. The tech then told me that the upgraded bullet proof FICM probably ruined my injectors, because my injectors we not upgraded. Is this True?
Even though my FICM is above the low limit for voltage, can it still be going out? I am taking the truck in to have the batteries load tested, so I will know if they are contributing to my FICM failing.
Ford 6.0L Power Stroke Diesel :: Truck Would Not Start And Threw FICM Codes
My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?
View 12 RepliesFord 6.0L Power Stroke Diesel :: FICM Will Usually Start In Low 30s And Gradually Work Up To Upper 40s
So, I've been having cold start issues for a couple of years now especially when temps get below 25 or so. It started with virtually no issues until temps got into the 20's but got to the point this year where it run a little rough at startup even in the summer. Once ECT gets up around 140* it runs pretty good.
I took it to a diesel shop last year and was told I had 1 bad injector and a bad glow plug. I couldn't afford to do the work, so I waited.
Now after researching this site, I'm more inclined to think it may just be the FICM. I've seen scangauge numbers in the low 20's up to 48.5. On cold morning FCM will usually start in the low 30's and gradually work up to upper 40's. The batteries were both replaced 2 years ago, but I probably should give them a load test. The alternator voltages vary from 11.0 to 12.5 when cold and 12.5 to 14 once warmed up. I have noticed that the AC blower will slow down a little when I sit at a red light, and then pick up again when taking off. I don't notice it with headlights or anything else.
According to Bismarc's spreadsheet, alternator numbers seem to be in the acceptable range, but I don't want to get a new FICM and fry it with a bad alternator. I can get the alternator or the FICM now, but if I need to do both at once I'll need to wait a bit longer.
Ford 6.0L Power Stroke Diesel :: 2004 - FICM Relay Location?
Just asking where about's the ficm relay would be under the hood of my '04 6 liter, I have 3 boxes to chose from.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Won't Start After Replaced All 3 FICM Connectors
I have an early 03 F250 6.0 that won't start after I replaced all 3 FICM connectors, also # 8 injector pin and connector. It has been almost impossible to start before the repair.
I checked the grounds on
Pins #1 2 3 22 they were all .5 ohms
Pin #32 was 1.0 ohms.
Pins #7 27 were 12.7v ( battery voltage)
I have double checked all pin connections and wire colors, they are in the right holes, I haven't done any cranking voltage tests, as I am alone. The FICM has 48.2 v.
Ford 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
I have a 2004 6liter. I parked one day two weeks ago and a went out last week to move it and I will only crank over. No fire No start!!!! Have new batteries. New fuel filter and have fuel coming in to the fuel bowl. I have gone over the harness, checked my fuses. I do not have a reader or scanner. Any recommendations. I want more than just a code scanner.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
ok, so after all the work done (headgaskets, head bolts, egr valve, ipr valve, egr cooler, oil cooler, blue spring kit, new ficm injector harness connectors), this is what I'm left with on start up. I am now getting no SYNC -0
I had ficm sync before i changed the connectors on the injector harness (last thing i did besides blue spring kit). Has this motor turn this way? And my glow plug light now comes on during and post crank along with a weird fuel light with 3 teardrops I've never seen before. I need to check this out.
48.0 ficm KOEO, 48.3 crank
IPC 3 KOEO, 1100 crank
IPR 14.1 KOEO, 46 crank
IPC volt .23 KOEO, 1.23 crank
Passed bubble test
Ford 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
2004 6.0 truck ran fine parked it, went out next morning and has been a crank no start. Brand new ficm put in today. Also scangauge readings while cranking.
IPR DUTY 30%
ICP -1000+
ICPV-.2 and rises
FICM-49.5 Never drop below 48
FICM LOGIC-11.5V And it also drops to 9 volts cranking
FICM SYNC-Yes
CAM/CRANK SYNC-Yes
I can here fuel pump running and have checked the bowl and fills in 3 second, also have held valve down in oil filter housing and it fills up in 4 seconds. Oil level perfect half tank fuel .. Also I get no smoke from tail pipe while trying to crank. Acts like it not firing or has no fuel... Driving me crazy been working on it for three weeks.
Ford 6.0L Power Stroke Diesel :: 2004 - Crank But No Start?
Just installed lots of new parts on this late 04 6 liter HPOP, Stand pipes, nipple cup orings, head gaskets. and now she wont go. Just cranks. Doing an air test now, should I be able to hear anything form the oil fill tube? It builds oil pressure just not right away, I did have an icp code. but has gone away as of now (p2285). What's consider a long crank time?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Low FICM Voltage Under Acceleration?
Pulled the trigger today and bought a 2004 F350 DRW King Ranch with 200000 miles. Using Forscan Lite on my iPhone, KOEO FICM voltage was right at 48. During start it went up a bit. While out for my highway road test for EOT/ECT differential (never went above 10 degrees).
I noticed that the FICM voltage would drop to the bottom of the Forscan scale (40 volts) when I was accelerating and then go back to 47.5 when I reached my cruising speed. Is this normal?
Batteries are brand new from Ford. I didn't notice the battery voltage. Truck seems to run great to me, but this is my first 6.0. I also got DTC's for all 8 injectors saying Injector Circuit Low.