Ford 6.0L Power Stroke Diesel :: F250 - Cold Starts Fine / Stalls Immediately After / No Throttle Low RPM
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
Ford 6.0L Power Stroke Diesel :: 2004 - Stalled Out While Driving / Starts Then Immediately Dies
Have a 2004 6.0 that stalled out while driving. Wouldn't restart. Took readings this morning. ICP was very low (below 100) and IPR was at 85. After a few times of taking readings I could get the truck to start up with an ICP reading over 500 but IPR was still at 85. When it did start up it would almost immediately die. Does this sound like an IPR problem or a oil pressure problem?
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Shuts Off On Its Own For No Reason
This has happened twice now, both times immediately after towing. I'll start it, begin to accelerate, and it will just putter out. It'll start right back up but it'll putter out again. After 20-30 minutes it'll start (and run). I have an edge programmer and it doesn't turn on when this happens. I get a turbo warning on it that the psi is at like 43/46 even though I'm essentially at idle so it seems to be getting a faulty error thinking the turbo is under too much load.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Battery Light Comes On / Engine Shuts Off Seconds Later
Last week my battery light came on for the first time in years. I have a 185 amp DC Power alternator after dealing with so many bad oem ones.
Anyways, battery light came on when i pulled up to a stop sign. I proceeded to plug my sct x4 in to see what the voltage was, with the battery light it was 11.50. I shut the truck off started it back up, no light and voltage was 13.7. Went through the stop sign got into some more traffic, started to accelerate again and this is when the truck shuts off for the first time. Put it in neutral, and it started right back up.
Several days later it shut off on me two times back to back. It was a cold start, and both times the battery light was on and the truck would die within 30 seconds. Third start it kept running fine.
This past Saturday morning battery light was on, let it idle for awhile then as i tried to park it in the garage it shut off. Started it up, no light so it ran fine. Later when i started the truck it shut off again. So it has shut off on me 5 times in the last week.
Some more background on the truck:
2005, 199k miles
Well maintained (T6 every 5k, filters every 15k, etc.)
The injectors are going bad, it started running rough saturday 1/9/16, just a couple days before it started shutting off.
I used to a sct x4 to pull codes, i have p2237 (if i remember right) which is an intermittent icp signal. I replaced the pigtail and icp less than a year ago because of the same code.
And three codes for glow plug solenoid open on 5, 6, and 7.
No ipr codes
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Truck Shuts Off For No Reason / Codes P0606 And P0341
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
Ford 6.7L Power Stroke Diesel :: 2013 F250 - Engine Turns But Will Not Start
I have a problem with my F250. The engine is turning, rail pressure 400kpa, but it does not jump at. Injectors are tested at bosch. High and Low Fuel Pressure Pump are new.Sensors and pressure regulator also. Compression is also ok on all cylinders.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Engine Went Dead Immediately After Passing Gear Kicked In
On cruise control, engine went dead immediately after passing gear kicked in. After 2 days on the side of the road got a pull to the house. Then after having a charger on it over night the electric seems to be messed up. Switched on, the dash lights light full strength for a fraction of a second before appearing as thought the battery is real low. Also the doorlocks act crazy. I think maybe I blew out the BB on the high oil pressure pump.
View 6 RepliesFord 6.0L Power Stroke Diesel :: F250 - Brakes Locking Up As Soon As Starts The Truck
I'm posting this for my neighbor who has a F250 that's 8 years old. He has replaced many parts, engine from what I know but now when he starts the truck it starts fine but as soon as he starts the truck, the brakes lock up. He can't move it. He hasn't had the chance to move it because the brakes lock as soon as the truck starts. It starts fine and idles fine but can't move because the brakes are locked. Tomorrow the tow truck will haul it to the ford dealership so they can look at it and run the diagnosis computer on it.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Starts And Dies Numerous Times
I've got an '05 F-250 starts and dies numerous times, have to rev throttle to keep running then it stays running. I've replaced FICM, PCM, Eng. harness, IPR, CMP, what else is there to do?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Starts Fine Then Dies After 2 Minutes
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
Toyota - Celica :: 2001 - Engine Turns On But Then It Shuts Off Immediately
I have a 2001 Toyota Celica gt, and I had a accident on the front of the car. The only things needed to be replaced was the radiator and the Intake manifold.The car wasn't drivable for about 3 months, but within those 3 months I was able to work on replacing the radiator and the intake manifold ( which a crack on it). Now that I finished working on the car, the engine turns on but then it shuts off immediately. Everything was replace properly, I just don't understand.
View 1 RepliesGolf IV / Jetta IV :: 2004 Starts But Shuts Off Immediately
When I parked this car 2 months ago it ran fine. Went to start it up and it starts and shuts down. I do not think its the security issue. Both keys do the same thing.
Battery is new recently. There are no MIL lights working on the dash except the battery light. The actual dash lights will not come on. Doors will unlock but not lock. My VAG tester will not communicate with the ECU.
I have checked all of the fuses multiple times. I can hear the fuel pump prime up when the key is turned on. It appears that there is an electrical issue. I took the connections off of the ecu, waited a bit, check for cleanliness and reinstalled also.
Sebring - Chrysler :: 2001 - Engine Starts Then Immediately Shuts Off?
A couple of months ago my daughter's Sebring engine began shutting off immediately after starting. We brought the car to my usually reliable mechanic. They couldn't find anything wrong. The problem became more frequent (every 2 to 3 starts) and we brought it back to my mechanic who determined it was the car's computer system. $1700 later the car is ready to be picked up, my daughter gets it after the shop is closed, and it wouldn't start! She left it there, got a ride, and, one week later the Sebring is still at the mechanic's. They told us it starts every time for them and they don't see any problem. After researching on the Internet I thought it might have something to do with the immobilizer but they told me that tested fine. I'm at a loss over what to do.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts But Have No Throttle
My 2002 f250 starts but has no throttle, I did replace the throttle body, still no luck, i did find a wire on the shiffter that had a bad spot , fixxed it still no throttle, code reader says it passes with no codes, I disconnected both batteries and waited 15 to 20 min, reconnected them, started the truck and let it idle for 20 min so what do i need to do now. I just cant figure it out....
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 Starts When Key Is Turned To Run
I have a 2000 F-250 7.3 L Diesel w/200,000+ miles on it.
I use the truck for snowplowing and last snowfall one of my employees broke the overdrive switch on the PRNDL shift lever. I just replaced it and as I went to start the truck I had just turned the key to run in order to let the glow plugs warm up and the truck attempted to start itself.
As it was running I could hear the starter continue to run although I never fully turned the key. I have since then replaced the ignition switch and the key lock cylinder. That didn't fix the issue, I then pulled the fuse box that is inside the cab of the truck to inspect the GEM module. Other than lots of dust there was no corrosion or any see-able issues with the module. I cleaned all connections thoroughly and even applied a little dielectric grease to the connections.
Still has the same issue, I ran a voltmeter to the trigger wire on the starter relay and it reads 10V when the key is turned to run. I believe it should not read any voltage until the key is turned to start. If I have the trigger wire on the starter relay disconnected the truck won't start, obviously. I don't believe the starter relay is bad because it does start only when the key is in the run position and it has never attempted to start without the key.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 Diesel - Engine Just Randomly Shuts Off Without Warning While Driving
My 2001 F350 7.3 dually diesel Automatic has been a pretty good truck but recently it has been dying. Engine just randomly shuts off without warning while Driving. Check engine light comes on sometimes. Some of the time it will restart if I cycle the key. Once its running again I can rev the engine up without a sputter but after a few hundred yards down the road it will die again. I noticed driving on the highway when it does it my truck will buck first, then...
If I leave it in drive with the key in the run position when it dies and I'm coasting down the highway the Tach starts jumping around like its trying to restart itself, all on its own. I don't have a scanner.
The last time it died I coasted into my driveway and it wouldn't restart, went back out there 30 minutes later and it fired right up. Its only 40 degrees here if that matters, not hot by any means.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts Then Dies - Shut Down While Driving
My truck is an 02 F250 7.3 with 280,000+ miles on it, so I wouldn't be surprised if I might have a number of things going wrong. It runs pretty good, but is still far from 100%, at least up to my standards. So the problem has been going on for the last two or three weeks and got worse today, and there were a few things leading up to it as well. I'll start off with the first thing that happened that I think might be related. It was about 6 months ago, my buddy and I were putting my new headlights in.
It was parked in his garage and we backed it out a little bit to try and adjust them. It was sitting there idling for a minute or two and just shut off or almost stalled out. Tried to restart it and it wouldn't start, tried multiple times to no avail. It acted similar to when I had glow plug troubles when I first got the truck, it would just crank and crank, but never actually kick over and start, along with putting white smoke out the exhaust. Ended up waiting about a half hour and then the truck fired right up with no problems after that, so I didn't think much of it.
Then fast forward to last week to when something similar happened. Started it up after sitting for a few days, started right up, idled for a few seconds and then just shut off. Started it back up ran for a second and died again. Tried a third time with the same result. Fourth time fired right up again and stayed running, let it run for a few minutes and was fine. Also along with this, there was a bad squeaking coming from the front of the truck, like what a belt would sound like. I have recently replaced the belt because it was squeaking and actually got chewed up and almost shredded completely apart.
So not sure why it is squeaking again, but not sure if this could be related or not. Then took it back to my dorm room to get my stuff, and then made it the hour or so drive home from school, without issue. Even went to a few stores before I went home, and shut the truck off and started it back up multiple times, again with no issues. When I drove back earlier this week it was fine until I got there and put it in park. It idled for few seconds and then cut out for a second, but then idled back up and continued to run fine. It has done that a few times as well. So it will do it on a cold start or after already fully warmed up.
Then it got worse today. Again had trouble starting it cold, same as what I explained early. Except second time cranking it wouldn't start at all, then on the third crank it started up and stayed running. But on the drive home is when it got worse. About 5 or 10 minutes into my drive, was just cruising doing at about 45 or 50, and truck just shut off, died/stalled out. It cut out and shut off for a second or two and then started itself back up and continued on like nothing happened. It scared the crap out of me the first time it happened, I was waiting for something like that to happen, but still wasn't quite ready for it.
The truck acted just like it would before you start it, with the key on, dash lights worked and the radio still worked. It did this 4 more times in similar ways, would die and then start back up, at various speeds and at roughly 5 or so minute intervals. I decided to just keep going as long as the truck would start and stay running, hoping to make it home. It did it a fifth time and this time the truck completely shut off and wouldn't restart itself. It was hard to see, as I was watching a few different things at one time, but I think it tried to restart, I noticed the tach bounce between 200-400 RPMS and then die. So I had to pull over and then restart it, fired up and drove fine. That was about half way home, and I made it the rest of the way home without any more problems.
So obviously I'm wondering what would be causing the truck to do this? I've done some reading and have a couple ideas, but not really for sure on anything. I was thinking maybe the CPS, I think it can cause a no start issue. Could ICP or the ICP sensor have something to do with it? I was also thinking maybe something fuel related, such as fuel pressure or a bad fuel pump. Any of those sound to be on the right track?
I have the torque pro app, but not exactly sure how to use it yet, and also just got access to my Uncle's Snap-on scanner, so I ran some tests and pulled some codes. How to more utilize these tools in diagnostics. I did get a few codes, but I'm not exactly sure how they might be related. The codes are pulled are:
P0470 Exhaust Pressure Sensor Circuit Fault. Just cleaned that out as well as the tube about a year ago, but I guess could be clogged again or has gone bad.
P1274 Cylinder 4 (E) High to Low Side Open. Did some reading and figured out that this could be UVCH related. At the same time, about a year ago, did new injector O-rings as well as all new Motorcraft UVCH's, so can't imagine that one is bad. Or that one could be loose, I would have guessed it would have happened more when I first did them, not a year later, but who knows.
Also pulled P1876 T-Case 2wd Solenoid Circuit Fault. Not sure if this is related at all, but also not sure what it means either. I read that it could be ESOF system related, which I do have, but I have manual lockout hubs, so maybe that's why it throws the code.
Also a few things that may or may not be related, but I think worth noting. Ever since I've had the truck the check engine light will pop on and off sometimes. It will do it on a cold start or, when I first start driving and its not fully warmed up yet. It does it most when the engine is still cold, and it almost never comes on once the truck is fully warmed up, but has came on and off more frequently lately. When driving, it will only stay on for a few seconds and more often when I'm lugging the engine or at lower rpms, and will commonly shut off if I let off the throttle.
I don't think it really comes on at higher rpms. I also have a slight oil leak in the valley of the engine, seems to maybe be coming from the front of the motor. Nothing too serious, leaves a small puddle where I park, loses enough to be at the add mark, a little before an oil change. Changed the oil about 1500 miles ago and have been able to notice a slight drop in oil level. Also I have changed the fuel filter in the last 500 miles.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts And Runs With Rough Idle For About 10 Seconds When Cold
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - When Engine Get Warm It Starts To Smoke Unburnt Fuel
I have a may 2003 6.0l f350 4x4 ,autoenginuity scanner, recently bought the truck starts fine and idles well then when engine get warm it starts to smoke unburnt fuel (white) volume of fuel desired on scanner goes from about 14 mm~3 to 27mm~3 and starts to run rough if you depress the acellerator the motor smooths out and the fuel desired goes down. No coolant smell. egr cooler removed ,oil cooler replaced, exhaust back pressure sensor and tube cleaned .ebp sensor koeo 14.2, eo 17 but jumped to 54.0 when map was at 17, bp 31.20 .... The AE is new to me Also found a superchip tuner under the back seat ...
View 14 Replies