Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts But Have No Throttle
My 2002 f250 starts but has no throttle, I did replace the throttle body, still no luck, i did find a wire on the shiffter that had a bad spot , fixxed it still no throttle, code reader says it passes with no codes, I disconnected both batteries and waited 15 to 20 min, reconnected them, started the truck and let it idle for 20 min so what do i need to do now. I just cant figure it out....
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Just Stop Running Like Key Turned Off
My 2001 f250 7.3 was running then just shut off like I had turned the key off, While trying to start back up, the truck turns over fine but no fire. I also have no gauges, I tested both fuse boxes and the one under the hood I have power on all big fuses, including the PCM but some of the small ones I don't, No power to the PCM diode, either side, the fuse box inside the cab, I have half power, No power to the PCM fuse is their a fusible link somewhere?
I really can't see much down there. The truck did get into a accident in Oct, which created a problem with the ignition and not sure if that could be a problem? That problem is, when I turn the vehicle off, it would stay running for a few seconds. I ignored the problem cause it didn't hinder the vehicle any.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts Then Dies - Shut Down While Driving
My truck is an 02 F250 7.3 with 280,000+ miles on it, so I wouldn't be surprised if I might have a number of things going wrong. It runs pretty good, but is still far from 100%, at least up to my standards. So the problem has been going on for the last two or three weeks and got worse today, and there were a few things leading up to it as well. I'll start off with the first thing that happened that I think might be related. It was about 6 months ago, my buddy and I were putting my new headlights in.
It was parked in his garage and we backed it out a little bit to try and adjust them. It was sitting there idling for a minute or two and just shut off or almost stalled out. Tried to restart it and it wouldn't start, tried multiple times to no avail. It acted similar to when I had glow plug troubles when I first got the truck, it would just crank and crank, but never actually kick over and start, along with putting white smoke out the exhaust. Ended up waiting about a half hour and then the truck fired right up with no problems after that, so I didn't think much of it.
Then fast forward to last week to when something similar happened. Started it up after sitting for a few days, started right up, idled for a few seconds and then just shut off. Started it back up ran for a second and died again. Tried a third time with the same result. Fourth time fired right up again and stayed running, let it run for a few minutes and was fine. Also along with this, there was a bad squeaking coming from the front of the truck, like what a belt would sound like. I have recently replaced the belt because it was squeaking and actually got chewed up and almost shredded completely apart.
So not sure why it is squeaking again, but not sure if this could be related or not. Then took it back to my dorm room to get my stuff, and then made it the hour or so drive home from school, without issue. Even went to a few stores before I went home, and shut the truck off and started it back up multiple times, again with no issues. When I drove back earlier this week it was fine until I got there and put it in park. It idled for few seconds and then cut out for a second, but then idled back up and continued to run fine. It has done that a few times as well. So it will do it on a cold start or after already fully warmed up.
Then it got worse today. Again had trouble starting it cold, same as what I explained early. Except second time cranking it wouldn't start at all, then on the third crank it started up and stayed running. But on the drive home is when it got worse. About 5 or 10 minutes into my drive, was just cruising doing at about 45 or 50, and truck just shut off, died/stalled out. It cut out and shut off for a second or two and then started itself back up and continued on like nothing happened. It scared the crap out of me the first time it happened, I was waiting for something like that to happen, but still wasn't quite ready for it.
The truck acted just like it would before you start it, with the key on, dash lights worked and the radio still worked. It did this 4 more times in similar ways, would die and then start back up, at various speeds and at roughly 5 or so minute intervals. I decided to just keep going as long as the truck would start and stay running, hoping to make it home. It did it a fifth time and this time the truck completely shut off and wouldn't restart itself. It was hard to see, as I was watching a few different things at one time, but I think it tried to restart, I noticed the tach bounce between 200-400 RPMS and then die. So I had to pull over and then restart it, fired up and drove fine. That was about half way home, and I made it the rest of the way home without any more problems.
So obviously I'm wondering what would be causing the truck to do this? I've done some reading and have a couple ideas, but not really for sure on anything. I was thinking maybe the CPS, I think it can cause a no start issue. Could ICP or the ICP sensor have something to do with it? I was also thinking maybe something fuel related, such as fuel pressure or a bad fuel pump. Any of those sound to be on the right track?
I have the torque pro app, but not exactly sure how to use it yet, and also just got access to my Uncle's Snap-on scanner, so I ran some tests and pulled some codes. How to more utilize these tools in diagnostics. I did get a few codes, but I'm not exactly sure how they might be related. The codes are pulled are:
P0470 Exhaust Pressure Sensor Circuit Fault. Just cleaned that out as well as the tube about a year ago, but I guess could be clogged again or has gone bad.
P1274 Cylinder 4 (E) High to Low Side Open. Did some reading and figured out that this could be UVCH related. At the same time, about a year ago, did new injector O-rings as well as all new Motorcraft UVCH's, so can't imagine that one is bad. Or that one could be loose, I would have guessed it would have happened more when I first did them, not a year later, but who knows.
Also pulled P1876 T-Case 2wd Solenoid Circuit Fault. Not sure if this is related at all, but also not sure what it means either. I read that it could be ESOF system related, which I do have, but I have manual lockout hubs, so maybe that's why it throws the code.
Also a few things that may or may not be related, but I think worth noting. Ever since I've had the truck the check engine light will pop on and off sometimes. It will do it on a cold start or, when I first start driving and its not fully warmed up yet. It does it most when the engine is still cold, and it almost never comes on once the truck is fully warmed up, but has came on and off more frequently lately. When driving, it will only stay on for a few seconds and more often when I'm lugging the engine or at lower rpms, and will commonly shut off if I let off the throttle.
I don't think it really comes on at higher rpms. I also have a slight oil leak in the valley of the engine, seems to maybe be coming from the front of the motor. Nothing too serious, leaves a small puddle where I park, loses enough to be at the add mark, a little before an oil change. Changed the oil about 1500 miles ago and have been able to notice a slight drop in oil level. Also I have changed the fuel filter in the last 500 miles.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts And Runs With Rough Idle For About 10 Seconds When Cold
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 Won't Getting Power?
OK . So here's the deal. My 2000 7.3 ford f250 170k miles. Going from phx az to flagstaff az . For some reason I'm hitting about 40 miles per hour with the pedal all the way down going up a decent grade. Seems like something isn't giving the motor power. I'm pulling a 28 ft toy hauler pretty much empty . Under 5800 pounds . What this could be . Also was get pretty close to the red on water temp gauge.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Major Power Loss And Shaking
I've got a 2000 F-250 with a 7.3. The other day I was driving down the road and it lost power and my foot almost went to the floor. I was at the bottom of a hill when it did this and I was running 60 mph. By the time I got to the top I was running 20 mph and had the truck to the floor. When I was driving it home it was tacking around 1800 rpm and my egts were only at 125 degrees. I know I'm not getting fuel. I thought it could be the fuel filter so I changed it. Still no luck. It'll start back up but it dies if I take my foot off the accelerator. It shook terrible when I was driving it home too. Is it injectors, uvch, hpop, or something else?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 Won't Start - No Power Passing Through Two Relays On Top Of Engine
Cooler weather has arrived and my 2000 f250 won't start. Wait to start light is coming on, no power passing through the two relays on top of the engine. Are both of these for glowplugs? My 97 only had one. How do I diagnose relays on this truck? If you cross out the two relays truck fires right off so I know the glowplugs themselves are good.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 Won't Turn Over Or Start
I'm having issues with my girlfriends truck turning over. It won't turn over at all. I'm not getting any power to the small wire on the relay on the passenger fender or the red wire with a blue stripe off the ignition module.
I've cleaned and tested the batteries and the terminals. I've replaced the ignition switch the ignition module the starter and the starter relay on the passenger fender and I've also checked the neutral safety switch. I've checked all the fuses and relays also.
It's a 2000 Ford 7.3l automatic.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 Shut Off And Would Not Start Again
I have a 2000 f250 7.3 with about 230,000 miles on it. So I filled my truck up to go out of town got on my way drove about 50 miles and the next stop I made the truck shut off and would not start again. I figured CPS went out again! nope changed it still not start. So check the fuel pump seemed fine was getting diesel. Checked oil, was a little low so i topped it off nothing. So i left the truck over night and came back on sunday still nothing. I finally got it started with a shot of quick start i know its not good but i had to get this Truck home. I drove and made it almost home took my foot off the pedal and it stalled again so i pulled it home. Had a guy go over and scan it and it says the oil pressure is at 30 psi when cranking so he says the hpop is probably bad.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Oil Or Fuel In Coolant?
I have a 2000 F250 7.3L and I pulled this from the overflow tank. I'm thinking it's oil since my oil cooler is leaking but just want to make sure it's not fuel and need to do injector cups...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Gauge Cluster Replacement
I just bought a 00 f250 cc that originally came out of Canada so the speedo and mileage is all in kilometers. I have bought a use cluster that is in standard units to replace it with. I am just curious if all I have to do is replace the cluster or if there is other thing that need to be replace as well to make it work right.
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Electric Fuel Conversion?
So I'm not sure if I should post this here or in the 1994.5-97 section. The reason being I have a 2000 f250 with a 97 7.3. It currently has a mechanical fuel pump but they keep crapping out. We dont have the money to do a $600 diy conversion so were looking for a cheap solution.
So the 2000 has all the fuel lines and plugs to put a electric fuel pump in, but if I just threw a electric pump on then it would feed to the mechanical fuel pump which I'm guessing is a no no? Or possible?
If I put the electric fuel pump would I just have to remove the mechanical fuel pump and run lines from the pump to the bowl?
If the fuel bowl can't hold the pressure of an electric fuel pump then would I be able to swap the fuel bowl only and be good to go or is that impossible?
Let me know what you think were trying to do this as cheaply as possible.
2000 f250 auto 4x4, 97' 7.3 motor.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Smoking When Rev The Engine And Imbalance On No 1 Cylinder
I have a 2000 7.3L f250 superduty. after rebuild and a yr now have engine smokes when you rev the engine and an imbalance on No1 cylinder causing injector to carbon up poss from prev misfires due to injector harness now solved? Found the turbo exhaust outlet pipe leaking oil we think because the wrong size clamp fitted. will fit new clamp tomorrow but if this does not solve problem what next? This has now cost thousands and still having problems...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Overdrive Light Blinking Randomly
I have a 2000 f250 with the 7.3 and 181,000 miles on it, recently got stuck in the snow (in 2wd because i forgot to lock the hubs) and the rear wheels did alot of spinning. Now i randomly have the OD light start to blink, sometimes its a half a blink, sometimes it'll stay on for a few seconds, itll do it randomly while crusing down the road at a constant speed, also noticed my rpms fluctuate a tad at idle.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Banging Noise From The Motor / Frequency Increases With RPM
00 F250 338k auto
No error codes or warning lights (Forscan verified)
No smoke out of the exhaust
No oil or coolant leaks
Have banging noise from the motor. When cold truck sounds normal, quiet. When it warms up, the banging becomes audible. You can hear it at idle. You can hear it under acceleration. Frequency increases with RPM
When at speed, and letting off the throttle, noise goes away.....comes back when back on the throttle. Any time during driving when I let off, engine quiets down to normal. To me it sounds like exhaust leak, bur not sure how to check for those?
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Transmission Fluid On The Floor / Hissing Sound When Cut It Off
I have a 2000 F250 4x4, it has been sitting in my garage for about 3 weeks. I cranked it up and backed it up about 10'. A few hours later I noticed a lot of transmission fluid on the floor. I remember hearing a hissing sound when I cut it off but didn't think anything about it. The fluid is on passengers side of truck, right side of the engine. Most of fluid is toward the rear but some ran down in front of the axle also. It's up high also, I've got fluid on rear of valve cover. I've cranked it up and let it run but can't get it to leak. Where did all this fluid come from?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 Runs Out Of Fuel On Hard Pull / Long Hills
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Codes P1247 And P1248 / Noise Sounding Like It Lost Air Compression For A Few Minutes
My pickup has 316,000 miles on it. It's a 2000 ford f250 7.3 powerstroke. I have always bragged how my truck can pull anything because it has alot of power. Yesterday when pulling a 28' travel trailer up an incline I noticed I didn't have much power and it steadily got worse. Now I'm at a crawl when I hear a noise sounding like it lost air compression for a few minutes then the noise stopped. I stopped and looked to make sure everything under the hood was still attached and everything seemed fine.
I got back in and continued very slowly a few more miles home. Gauge were all good, never got hot. I put a scanner on it and it threw two codes. P1247 and P1248. I haven't noticed any unusual smoke. This is my second ford I've owned and know that when weather gets cold you may have to plug it in. But this truck it doesn't matter if it's 100 outside it will not start without plugging in for at least 1 hour. I've replaced all glow plugs hasn't worked. So I am assuming this break down now has something to do with it. I really am starting to not like fords!