Prius (2004-09) :: Air / Fuel Ratio Sensor Connector Location?
I am getting code p0420 and want to replace the air/fuel ratio sensor and cannot figure out who to reach and remove the connector to the sensor. How to do it? I read several threads about it and saw instructions for the rear O2 sensor but not the fwd air/fuel ratio sensor.
I hope to remove it from below and avoid removing the inverter. From under the car I can see the cable leaving the sensor and I think I see it terminating in a connector on the left side of the engine. I can barely snake my arm up there and touch it, but I cannot get a good enough grip to press a release button and pull it free.
I got the rear O2 sensor changed in about 45 minutes.
Phaeton :: Location Of OBD Connector / Forward Fuse Panel Release Handle
My car is getting close to the 55- thousand mile service, and correct me if i am wrong the service is not mentioned in the owners handbook unless i overlooked something. However for the first time since i have the car the service due message is counting down in the readout.
Recently the CEL came on again, giving me an opportunity to use VAG adapter to read out the error code from memory. So went to open the panel underneath the steering wheel which contains the OBD connector. And that's when i got stuck.
According to the owner hand book the compartment has a little latch to open it. The only latch i found is the one used for the hand brake release. So what am I overlooking ?
Ford 6.7L Power Stroke Diesel :: Clearance Lights Plug In Connector Location?
Do all New trucks come with the factory clearance light plug-in-connector and if so, where would it be located? The reason I ask, is I'm considering adding the cab clearance lights to my 15 F350. Really would like the factory lights but I hear Recon makes some similar.
View 14 RepliesCamry :: Location Of Fuel Filter In 2008 Toyota
I own a 2008 camry 2.4 A/T and want to replace the fuel filter, where its located ?
View 9 RepliesCamry :: 2011 Toyota 3.5L V6 - Code P0157 / O2 Sensor Location
I have a 2011 toyota camry. 3.5L v6. I have code p0157. I know my car has 4 o2 sensors, but I am not sure which one to buy. Where this o2 sensor is located, and which one to purchase. A part number would be very useful.
View 3 RepliesCamry :: 2003 2AZ-FE Oil Control Valve Screen Location
I cannot find the Oil Control Valve Screen location for my engine. I have also seen one post that said this engine doesn't have one, but I thought that was odd.
View 14 RepliesCamry :: 2007 Navigation Screen Error / MAP DVD - Unable To Read Data
My new '07 Camry with 5K miles on it, driving along, minding my own business. The navigation was on as it always is, but not in guidance mode. All of a sudden I notice the screen turn dark and I see this error: "MAP DVD - Unable to read data. Check if map DVD is correct." (see image)
I have never removed the DVD from the drive. It is clean as a whistle. I wasn't on a bumpy road. I tried resetting and cleaning it, but no good.
Ford F-150 - 1997-2003 :: Freeze Data - Weak Acceleration?
while trying to diagnose a check engine light. 2003 4.2 2WD Manual F-150. 135,000 miles.
Some background:
-I have changed the lower O2's fairly recently, but not the uppers
-Never changed MAF
-I checked for vacuum leaks in the last 18 months, none found
I pulled some freeze frame data after my hour long ride to work today, and this is what I have. Where I should go from here?? Truck seems to be running fine, but just "weak" when it comes to acceleration. There is smooth ideal and cruising. I am getting 20.2 mpg, mostly highway miles.
P0171
Fuelsys1 CL
Fuelsys2 --
Load Pct 87.5
ECT 188F
SHRTFT1 5.5%
LongFT1 28.9%
SHRTFT2 1.6%
LongFT2 28.1%
RPM 2115
VSS 50 mph
If there is other data you might need, I can pull it. I think I had a 0.01 lb/s reading on MAF when I did a separate test. That was likely at idle though.
Camry 2012+ :: How To Reverse Polarity While Wires In Connector
I bought new HID bulbs from TRS but how do I reverse polarity while wires in connector. How do I remove it?!
View 14 RepliesCamry :: Gen 5 V6 - Red Airbag Light On / Loose Connector Under Driver Seat
I recently bought a used '06 Camry V6.
After driving it for several days, the red airbag light went on on the instrument panel. Certainly, I do not want to go to the dealer, not only because of costs, but also cause of the distance of the dealership from my home.
I did a bit of a research and so far have tried disconnecting the ground wire on the batter for half an hour, in order to reset the computer. Although, as soon as I plugged in the wire back and turned the car on, the light did not disappear.
After looking online, I found a similar problem and a solution regarding Toyota Sienna in this link: [URL] ....
-Following the advise, I remember that right before the light went on, I have tried to reach for the plastic water bottle that ended up deep under the driver's seat.
Is it possible that the airbag problem stems from the loose connector under the driver's seat? If yes, how should I approach this.
Also I recently had my intermediate steering shaft replaced [URL] .... Are there chances that such replacement caused the airbag to fail. This manual does not tell any steps to disconnect any yellow wires (or wires at all).
Camry :: 2004 - Spark Coil Connector Holding Crack Off?
Scheduled maintenance for changing spark plugs for my Camry 2004 2.4L is either 120k miles, or 144 months (12 years). My Camry reached 12 years first. In removing the coil connectors, 3 of 4 holdowns cracked off. I guess not so surprising after 12 years subject to engine heat. I'm NOT going to replace the connectors. Looking for a patch for this problem? Duct tape will just result in adhesive getting everywhere it shouldn't. Maybe there's a high temperature "crazy glue" I could apply at the connector interface that will last another 12 years, or 120k miles?
Otherwise, I'll use the "hope adhesive". That means I'll just hope the connectors don't work loose at a bad time.
Camry :: 2007 V6 - Wire Unseated From Connector During Ignition Coil Removal
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 RepliesCamry :: 2004 - Ignition Coil Connector Broke - Connect Directly?
I replaced my valve cover gasket yesterday on my 2004 Camry. While putting back together, three of the tabs on the connectors for the ignition coil harness snapped off and would not stay together because of tension on the harness. I tried to zip tie them because I read that in another forum post but the clips (alligator clips?) inside the connector did not seem to be making contact with connector on top of ignition coil. The car was mis-firing and running very rough.
After much frustration, I finally removed the wires with the alligator clips from inside the connector and plugged them directly into the top of the ignition coil. Well, the car started and seems to be running/idling fine although now the Check Engine Light is on. Also, I have not driven car yet.
My question: Can I drive the car like this or will the vibration from the engine eventually loosen the connections. I am planning on ordering the connectors but they will not be in for a few days and I need to drive the car.
Camry :: 2006 - Little Keeper Clips Broken On Connector Plugs That Connect To Coil Packs
Changed the spark plugs on my 2006 Camry today. Everything went smoothly and quickly except for the fact that I broke all the little keeper clips on the connector plugs that connect to the coil packs. I called my Toyota dealers and one said I had to replace the entire wire harness. The other found the connector plugs for around $8 each. Will the broken clips be a problem with the connectors eventually coming off from vibration if I don't replace them? I'm not sure how to replace the connectors if I go that route. How to go about replacing the connector plugs?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Engine Coolant Reached 270 Degrees On OBD Link MX?
Just got my truck back (450) from rebuild on tranny. Hooked up my new obd link mx , and was out running the truck for a while. Started running it pretty hard to see what the gauges would do. Noticed the engine coolant was getting up pretty high, usually around 240-250, and then hit 270!!! My temp gauge on the truck wasn't budging , just stayed between hot and cold. Is this normal?? Seemed pretty hot to me but if i just took it easy on the throttle it would average around 230. If i stop and idle it quickly goes down to 206. Look at oil temp and tranny temp also engine coolant temp is bottom middle.
View 6 RepliesFord F-150 - 1997-2003 :: 1998 - Suddenly Died / Cranks But Won't Start - Back Link Error Code
My 4.2L died all of a sudden, it cranks but won't start. Checked the harness side to coil packs, pos. signal but no neg. Tried a code reader keeps coming back link error. Does this mean PCM is fried?
View 4 RepliesCamry :: Low Idle RPM On 2003 Toyota
I have a 2003 4-cyl. Was running OK til starter died. Changed the starter, now it starts fine, but has idle problems similar to a dirty IAC. Sounds a lot like this thread: Low idle rpm problem on 2003 Toyota Camry: How I solved it
Haven't tried that fix yet. I was wondering if there anything else I could consider, due maybe to disconnecting the battery causing computer problems or something like that?
So I decided to run it for a while, thinking maybe the computer needed some more data. Idling about 100, but driving OK (around the block) but definitely not right.
Then the check engine light came on; I need to pull the code of course but need to borrow a code reader.....
Ford F-150 - 1997-2003 :: 1998 - Fuel Filter Connector Stuck
98 F150 4.6L 4WD...
Attempted to replace fuel filter tonight. The connector on the fuel tank side of the filter came off just like it is supposed to. The engine side, however, will not come lose at all. I can wiggle to back and forth, but I can't seem to get the tool to compress the springs.
The engine side connector seems to be smaller than the tank side. I've done this once before on a '98 Ranger, but didn't notice a difference in connectors.
Ford 7.3L Power Stroke (1999-2003) :: Diagram Of OBD2 Connector
Looking for the wiring diagram with colors for which port should be what wire for the obd2 connector for my early 99 f-250. I actually think it is obd 1 on our trucks but you get the idea. My truck doesn't have power to the plug I guess. I have a guy plug in a scanner to take a look at everything but he said the plug wouldn't power up his scanner. Just trying to get this fixed. Another question, if I buy a AE does that require the truck to power up the software or does it get powered my the laptop?
View 11 Replies