Ford 7.3L Power Stroke (1999-2003) :: 2001 - Hard Start - Flat Spots At High Speed?
I have a 2001 F350 Dually 7.3 w/260K miles. Hard starting, it has to be plugged in all the time. Occasionally/most of the time, blows white smoke at 50 to 60 mph or at high rpm. Replaced TPS and now runs totally different on starting, still hard to start but better throttle response on starting. Once started, I have to pedal it to keep it running, which seems to have little response as it would as if it was a direct throttle linkage attached to a carburetor...follow me? After a while, it will idle by itself. However, it still has flat spots when out of idle and at high rpm. Has gotten to the point that I can't trust to drive it.
View 4 RepliesSanta FE SM (2001-06) :: Lack Of Power / Rough Running
Well today I have moved on to the next project on my 02 v6 4X4 Santa Fe, which is the rough running. When I got the car, it had CEL with codes for misfire #5 and lean condition codes. I noticed the wires were in need of replacement (one had black tape wrapped around it) so changed the plugs and wires. The 2 hoses, one that goes between the valve covers on the pass side and the hose between the valve cover and throttle body on driver side were both cracked so replaced them along with a few other vacuum lines, just because I had access to them. Cleared the codes and it still runs like crap, but after 112 miles, town and highway driving, there are no CEL codes. When its first started it idles at 1500 and sounds like its missing and has very little power going down the road. When it warms up seems to run a bit better but still nowhere close to what it should. Equal compression on all 6 cylinders and has power to all 6 injectors and tested to be sure there was a pulse to them as well. Coil packs all tested well. the exhaust is in bad shape and don't know if that would have any effect on how its running.
View 6 RepliesFord F-150 - 1997-2003 :: Idles Rough And Seems To Lack Power
I am working on a 97 4.6 with 146k for a friend. It idles rough and seems to lack power (then again a 4.6 lacks power )
Has New:
plugs
wires
coil packs
fuel filter
sea foam intake
sea foam fuel
I have checked:
proper egr function
vacuum leaks
cleaned IAC
steady 17-18 in vac
clean air filter
cats do not seem to be getting too hot.
no codes
KOEO test ok
KOER test ok
The plugs worked some. Dirty MAF, clogged cats??
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 RepliesPhaeton :: Won't Hold Idle / Flat Spots During Rev
I had the car in to replace the inner CV boot and repair a leaking trans flex seal. About 30 minutes after I left the shop, I lost all acceleration and the car basically crawls around. Halfway to work and almost late for meetings, I was afraid it was a failing fuel pump so I rigged both fuel pump relays closed and it seemed to get better... I pulled the relays while at work, re-inserted at the end of the day and headed home. About halfway home the acceleration issues came back (with the rigged relays), and I barely made it to my driveway. Pulled codes, and see these:
16732 - Camshaft Position Sensor (G163)
P0348 - 001 - Short to Plus - MIL ON
18711 - Leak in Air Intake System
P2279 - 002 - Lower Limit Exceeded - MIL ON
16408 - Bank 2: Camshaft B (Exhaust)
P0024 - 008 - Retard Setpoint not Reached (Over-Advanced) - MIL ON
I checked for vacuum leaks and can't seem to find anything tell-tale. I have seen the Camshaft Position Sensor before, but the car ran fine. Probably time to get around to replacing it, but what about the Leak in Air Intake System? Car really hates to idle. Also, MIL is pretty much always on for me due to an unhappy trans that disables ESP.
Ford Escape / Hybrid :: 2008 - Flat Spots On Tire
So I have a 2008 escape 4wd.... I am getting a few flat spots on the inside passenger rear tire... So I figured it was the shocks so I unbolted both and cycled them and they both felt the same... There was dampening you can feel the oil going through the valves or whatever... I have felt completely bad shocks before and it was just a smooth motion when cycling the shocks... Can it still feel like there good but there not? The thing has 85k on it and I'm not sure if they have ever been replaced before..
View 6 RepliesPassat (B7) :: 2013 - Flat Spots On Acceleration As If Transmission Is Trying To Catch A Gear?
Have a 2013 Passat Tdi. It seems that sometimes when i accelerate the car doesn't move it has a flat spot as if the transmission is trying to catch a gear. I know this might sound minor to some folks. However on several occasions I've pulled out into oncoming traffic not expecting it to have a flat spot in the car not moving at all. What's up with this?
On the highway no problem and normal acceleration no problem but if you're going from a stop or pulling away from a intersection seems that happen more so than I would like.
Golf IV / Jetta IV :: Running Rough / Flat Spot When Accelerating Around 2000 And 2600 RPM
My 2.0 recently had some problems with the coil pack so I replaced it. Now my car hits a "flat spot" when accelerating around 2000 RPM and then another around 2600 RPM. If I am in 3rd gear going about 20MPH and I press the gas about 25-30% it sort of shakes and won't accelerate and when I take my foot off the gas and slowly ease the pedal down it accelerates fine.
My car also runs pretty rough at a cold idle(misfires). When I press the gas it sounds smooth until it gets back to idle. At any temp my car runs really rough with the A/C on. I also hear a rattle/Buzz around my relay panel when the A/C is on. My car is a 1999 2.0 AEG. I don't have VAG-COM just a generic scanner and the last codes I got were:
P0134
P0135
P0141
I replaced both O2 sensors and the beginning of this year and those codes came back right after I did them. I will scan tomorrow and post any new codes.
Ford 6.0L Power Stroke Diesel :: E350 Dying When In Gear / Lack Of Power / Rough Idle
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Rough On Cold Startup - Surge / Lack Of Power During Light Acceleration
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesSonata NF (2006-10) :: Rough Idle / Lack Of Power Under 2000 RPMs
I have a 06 sonata 3.3L v6. I have been having misfire problems and lack of power under 2000 rpms and at idle when I am either a stop or just warming the car. What is happening I feel it shake and feel the misfire but after it gets up after 2000 rpm at highway speeds its completely fine. It struggles getting up to speed if i press on the accelerator. I have changed the spark plugs and all the ignition coils maybe about 2 months ago, I have also have changed the camshaft position sensor for the rear bank. I believe that it could be the crankshaft position sensor but I want to make sure....
Obd2 codes: p300,301, 303, p0012, p0011, p0014,
Ford 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Running Rough - Missing - No Power
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough And Had No Power / Died While Driving
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
Ford 7.3L Power Stroke (1999-2003) :: Rough Running / No Power After Just Driving A Block Or Two
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 7.3L Power Stroke (1999-2003) :: Running Rough When Accelerate / Bogs Down And Looses Power
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 RepliesNissan - Pathfinder :: 2006 - Tough Start / Rough Idle And Lack Of Power
I have an 06 Pathfinder LE that was running fine earlier. got to a location and when i went to drive home it was a tough start, rough idle and lack of power. got an 0302 code so i changed out the plugs and swapped the # 2 coil for # 4. once started still ran rough as described. read code again after clearing and code still ran 0302, didn't follow coil. is the #2 coil on drivers side as i have read?
View 8 Replies