Camry :: 2006 / Brakes - Intermittent Sinking Pedal?
2006 Camry, intermittently the brake pedal sinks by going a inch or so further than normal. Car still stops and I don't think it is all the way at the floor. It is not very frequent, maybe 5% of the time. When it does occur it always happens on a second pump while slowing to a stop or turn, so the car is always going below 10 mph when it occurs.
Mechanic can find nothing wrong with the brakes themselves or any air in the lines. The fluid level is stable. I am guessing it is either the master cylinder or booster. Is there a way to diagnose which one it might be? Could it be a vacuum leak due to only showing up at low speed?
Toyota - Camry :: New Brakes Squeak After Remove Foot From Pedal
Two days ago I had the front brake pads on my 2003 Toyota Camry LE replaced because they were squeaking when I stopped. That squeak stopped, but after driving about 15 miles, I heard a squeaking noise AFTER I took my foot OFF the brake pedal. Pressing the pedal makes the squeak go away. I took the car back the next day and they changed the front rotors. While driving home, the squeak returned. I took the car to my regular mechanic this time. He says the guys who installed the brakes didn't clean anything when they put the new ones on, so he disassembled everything, cleaned the rotors, etc. and put everything back together. He also said they put the wrong pads on the car - I need ceramic pads and they used the metallic kind. Well, the brakes are still squealing when I'm not pressing on the brake pedal and stop squealing when I do press it.
Characteristics of the squeak....It only seems to happen when I drive the car more than 5-10 miles. When I drive a short distance, it doesn't happen. The sound is rhythmic, not constant. If I step on the brake and let if off slowly, like at a stop light, I can hear it "squeak, squeak, squeak" as the tire rotates. The faster the wheel spins, the more constant the sound. It only seems to come from the driver's side.
I hate to take the car back to the original shop because I don't think they know what they're doing. I'm scared of getting ripped off at one of the big chains (I'm a female and of course whenever I take a car in for service at one of those places "everything needs to be replaced.")
Will Toyota ceramic pads fix the problem? Can the wrong pads cause the brakes to squeak when you're not stepping on the brake pedal? Someone else suggested it might be the caliper binding and that would require replacing it.
Ford Brakes/Suspension :: After Pressing Pedal Resistance Became Really Soft And Brakes Very Sensitive
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 RepliesFord Brakes/Suspension :: 1997 F250 - Hard Pedal / No Brakes Intermittently
I have a 97 F250 that is having reoccurring brake issues, It has an intermittent hard pedal with little to no brakes when it occurs. It will stop but you are standing on the pedal with both feet. I have replaced the booster, master cylinder, and the vacuum pump in the past trying to isolate the issue and still had the problem. On this year model the abs ids only on the rear correct???? if it is shouldn't it only be affecting the rear brakes? Since this truck has a dual reservoir MC the front should still work?
View 4 RepliesFord Brakes/Suspension :: 2003 F250 - Brakes Pedal Pulsed A Bit
If this was my car or older truck I would know what the deal was. First hill I came down in my recently bought 2003 F250 the pedal pulsed a bit as I tried to slow down...is this the way ABS brakes behave? Never had them on a truck before...she stopped ok but don't know if they are warped or normal ...I'll pull wheels later (not a daily driver)...
View 7 RepliesFord Brakes/Suspension :: Consistent Squeaking Coming From Back Drum Brakes When Pedal Is Applied
After putting my Ford Ranger in park and pressing down on the E-break to get the news-paper or mail. I've noticed that there is a consistent squeaking coming from the back drum brakes when the brake pedal is applied. But only for a certain period of time; then the squeaking stops.
View 8 RepliesAvalon :: Brakes Pedal Doesn't Go Down As Far
I just got my 2014 Avalon XLE Premium and the brakes seem a little strange to me. When I first press down on the brake pedal the pedal goes down and the brakes seem a bit light, when I let up on the pedal and then push right back down the pedal doesn't go down as far and the brakes are firmer.
View 2 RepliesPassat (B5) :: New Brakes - No ABS Vibration In Pedal?
I recently noticed that my car wasn't performing the ABS self-test (that little brake pedal vibration and sound you hear when you reach 5 mph backing up on the first start-up of the day). Saturday I had to make a sort of emergency stop, and I didn't feel that ABS vibration in the pedal, and I even skidded slightly.
There's no message on the display about the ABS or anything else. I did recently have my front pads and rotors replaced with OEM parts, including pads w/sensors. Is there anything the mechanic could have done while replacing the brakes that might have messed up the ABS.
Celica :: When Pump The Brakes Pedal Gets Stronger
I drive a 95 Celica with the 1.8L. when there's air in brake lines, and pump the brakes, the pedal gets stronger? It's kind of like that, except my friction point gets lower and lower to the floor. My clutch reservoir was a little below the MIN line but filling it didn't work. I'm assuming air may have gotten into the lines, but how to bleed them.
View 5 RepliesVolvo :: Replaced The Brakes But Pedal Still Spongy
My 89 240 is a project car so I am just fixing everything up as new until it's all done.
Replaced the Brake Booster with a fully reconditioned one, a new master cylinder, full pressure bleed, new pads. Now I have fantastic brakes but they feel super spongy still . As an example, I make an emergency stop to check if they are ok and after stopping just fine , the pedal still wants to go down further. I have checked all the flexible lines for ballooning and they are ok .
Lexus LX 2008+ :: Brakes Will Not Engage Until Pedal Is At Least One Third Of The Way Down
The brakes will not engage until the brake peddle is at least 1/3 of the way down, resulting in a big delay in time to stop. In stop and go traffic it is very dangerous. I have to actually "ride" the brake in rush hour traffic in order to be ready for a quick traffic problem as this brake system is very slow to respond. This is obviously a safety flaw in manufacturing or design but it must be fixed as its not a matter of if an accident will occur but when will it occur. I test drove another LX 570 and found the same brake issue with that unit as well.
View 14 RepliesDodge :: 1936 - Brakes Pedal Goes Right To Floor
I give up. I have been trying for a very long time to get the brakes on my 1936 dodge to work with no results. The whole system is rebuilt, new lines, resleeved and rebuilt wheel cylinders, rebuilt and resleeved master cylinder, no leaks in system, pressure bled, vacuum bled and new lines. I even had a mechanic try and get them to work. He said all they needed were to be bled very slow. he actually got them to work slightly but after the car sat for a week the brakes were gone again. Drums all around, master cylinder is single cylinder. Brake pedal goes right to floor.
View 14 Replies7 Series :: 83 733i - Soft Brakes (Pedal Right To The Floor)
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
Subaru - Outback :: No Brakes / Pedal Hard When Cold Outside
For the past 3 yrs only in the winter when its around 30 outside where my car is parked after i start the car and put it in reverse to back up i have no brakes, the pedal is hard, i have to put direct pressure and hold it down til it softens to the floor after about 5 to 10 seconds then i have brakes for the rest of the day. But this winter and its still cold out it has been happening intermittently during the daytime going front or back i have to try and pump the brakes til the peddle softens or i just press the peddle hard and hold til it softens and then it works takes about 3 to 4 seconds in the middle of the day. Only happens when i first start up the car. I have replaced the pads, rotors, master cylinder, flushed the whole system and the latest money drop was replacing the booster.
View 17 RepliesBMW - 328i :: 2011 - Pedal Get Sticky When Brakes Applied
My car is a 2011 BMW 328i Coupe, currently at 24K mi. Recently i found my cars brake pedal get sticky after Ive applied the brakes from time to time. But nothing server. My routine schedule maintenance will be coming up soon, so i am just wondering what could be the probable cause. Could it be the brake fluid?
View 6 RepliesSanta FE SM (2001-06) :: Brakes Pedal So Soft That It Goes To The Floor
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
Dodge - Ram :: Pedal Hesitates Before Moving When Brakes Applied
A couple of years ago I bought an older used pick up to pull our camper and do any general hauling I might need. It is an '04.5 (they made some changes mid model year) Dodge Ram 2500 turbo diesel. It was high miles when I bought it (hence the reason I could afford it) with upwards of 300k but that is about midlife for this type of truck so I wasn't worried. It has been a great truck over all with only odds and ends that you would expect from an older high mileage truck.
However, it has one issue that started not long after I bought it and persisted for about the first year I had it. When I apply the brakes the pedal hesitates before moving. The brakes work fine other than this but it is a bit unnerving when you hit the pedal and it doesn't move for a full second. It is only about a second and then it releases and works fine.
I thought the problem had gone away when it started braking normally for something like six months but lately it has started doing it again. I know it does this and plan accordingly so I have not had any close calls but still, I would like to fix this. I cannot find any data on this problem.
Golf IV / Jetta IV :: 2002 - Brakes Has No Pedal Pressure?
Im having problems with my brakes mainly being pedal pressure. It's really really soft and has no bite till near the bottom which could be due to the res being low on fluid since both rear calipers seem to be leaking from the handbrake mechanism. When I got my car safetied they fixed my handbrake but I think they put the adjuster to tight cause I felt more rub then what I thought was normal but could be completely wrong. Not to mention this starting happening the day after I got it safetied
the handbrake bracket didn't retract like the other side but since then I loosened the compensator and pulled both side handbrake lines off and retracted the handbrake bracket by hand so now it looks like the right side.
Thunderbird :: 1996 - No Brake Pedal - 4 Brakes Bled?
My 96 thunderbird had a rear caliper shot. I changed the caliper, the rotor, and the brake pads then bled all the brakes. The three I didn't touch bled perfectly when someone in the car pressed the brake, I let fluid flow, then tightened the nut. The wheel with all the new parts I get zero fluid out of. I removed the brake line completely and pumped the brakes and still no fluid. It has no pedal and three of the four brakes have been bled. My only guess is there is air in the line but why wouldn't any fluid come out if I continually pump the brake pedal with only that one line open?
View 8 Replies