BMW :: 2004 - Engine Hesitation When First Started
I have a 2004 325ci. The car will hesitate when first started and not move. It's as if the car is in neutral when I step on the gas as the engine revs and then all of the sudden it jumps into gear and takes off. I had it checked last year for the first time and I was told it was the transmission, that didn't set well with me as that is $5k. I took it to the dealership and they re-programmed it and that worked some as it was August and made it much less noticeable and then it went away as we were moving into the cooler months. I live in Vegas and it is starting to approach those 3 digit temps and the problem is back. It only happens in the warmer temperatures. When I first bought the car in '06 it would have this problem every now and again and it wasn't consistent. Now its very noticeable and driving me crazy! There has to be another reason besides a re-program??? i know the people in the parking garage are wondering why this lady can't drive a stick shift!
View 2 RepliesChrysler - Towncountry :: 2005 - Gauge Needles Move Up And Down When Car Started
I drive a 2005 Chrysler Town and Country with just over 47,000 miles. I noticed that during the last few days, when I start the car, the needles on the fuel, speedometer and temperature gauges go all the way up and then back down. After they finish moving, I then see the engine lights go on and off. Normally, when I start the car, just the engine lights go on and off. The movement of the needles on the gauges is new. This is now happening about every other time I start the car.
The car itself seems to be starting and running just fine. I haven’t noticed any drop off or change in performance. What could be causing this oddity? Is this a warning that something worse is about to happen?
Gmc :: 1999 Yukon Started To Snap To Left Or Right When Move The Wheel Just Slightly
I've got a 1999 Yukon with a new (rebuilt) engine ad a new (rebuilt) tranny, both only about 3-4 years old. Within the last 2 years it has started to 'snap' to the left or right when I move the wheel just slightly. My husband tightened the steering and that worked a little but it still does it. It's pretty scary when your on the highway and go to adjust your lane placement and the wheel jerks out of your hand in the direction you're turning! Also, the truck has also developed a nasty habit it simply shutting down while I'm driving. The last time it did it I was on the freeway doing 65! It always starts right back up but I'm worried that one of these days it won't and I'll find myself in a real pickle! Nobody I've talked to (including mechanics!!!!) seem to know what these problems are.
View 1 RepliesFord Transmission :: 1994 - Cannot Move Engage In D But Will Shift Fine If Started In 1 Or 2
I have a 1994 F53 Chassis RV that has recently developed a transmission problem. The transmission has been working fine then one day I went to move the RV and I put the transmission into “D” and nothing happens. It feels like it is still in Neutral and there is a slight metal on metal sound like it is trying to engage. However if you the put the transmission in reverse it works fine.
I then put the transmission into “1” or “2” and the RV moves with no problems. Then once it is moving I can shift it into “D” and the transmission will act like normal and shift into 3<SUP>rd</SUP> and 4<SUP>th</SUP> gear. That is until I come to a stop again. Then it feels like the transmission goes back into “N”. I then can shift back into “1” or “2” and get the RV moving I can shift it back into “D” and everything works again.
I have checked the transmission fluid and it could use changed but the level was fine. I have read about the MLPS could that be causing this problem? I have read about testing the MLPS, but I am not sure which pin is which.
Acura - Integra - Hesitation :: 1992 - Tachometer Started Bouncing Up And Down
My '92 Integra has ~280K miles. A couple of years ago the tachometer started "bouncing" up and down while the engine seemed to run fine. Some time after, it started to hesitate under acceleration. A few months ago the car died while driving along the highway. The tachometer went up and down as the engine cut off and came back on before finally dying. A tow to the repair shop lead to a tune up, changing of spark plugs, wires, distributor cap and the ignition coil. That got the car running again, with its usual erratic tach and hesitation on acceleration. Then, the car died again in a similar way while driving. I was found to have a dead battery. Replacing it got the car running again...but the tach is still erratic and the car still hesitates. I am concerned that there is still some underlying issue that has not been fixed. I sometimes think it is a loose connection because there are times when the car seems just fine, but that is happening less frequently.
View 3 RepliesFord - Mustang :: Fuel Gauge Started To Misread And Now It Doesn't Move At All - Code P0460
I have a 2005 v6 ford mustang with 134,300 miles on it. About three weeks ago the fuel gauge started to misread and now it doesn't move at all and it dose have gas. Two days ago the check light came on so I connected to to a code scanner and it gave me the code P0460. Under the code it gave a short discretion, (Fuel level sensor A circuit). What issue might be?
View 3 RepliesFord F-150 (2004-2008) :: Hesitation And No Start / Smoke Started Coming From Under The Hood
I have a 2004 F150 4x4 super crew with te 5.4L in it. Truck has 200K plus miles on it and I went to start it after driving (it may have say for 10 min) the truck hesitated and didn't start and smoke started coming from under the hood. Looked like it was coming from the drivers side maybe mid fender or closer to the firewall. Look at it and nothing was on fire but something defiantly happened cause now its compensating for something. The rpms are up from what they usually are and the drivers information was cleared. Truck runs now but just worried
View 6 RepliesFord 6.0L Power Stroke Diesel :: No Response When Pressed The Throttle And Started To Move At Signal Light
2003 F350 6.0 cc 4x4 with 291k... Not sure if I have a problem or not, it happened at a signal light: The light turned green, I pressed the throttle and started to move. As I pressed more, there was no response. Second later it took off and I have had no more problem. What the cause maybe?
View 1 RepliesFord Super Duty (1999-2016) :: Takes Longer To Start And Needle Doesn't Move Until After Motor Started
It used to be, if I remember correctly, that while turning the key on a cold start the oil pressure gauge needle would show pressure prior to the engine starting, now it takes longer to start and the needle doesn't move until after the motor has started. I had the O-ring kit replaced due to oil leakage, and I wonder if there is an issue with the system. N to watch as they deedo their cold start today...
View 4 RepliesFord - Explorer :: 2007 V8 Started Running Horrible / Rough Idle / Drives Badly And Hesitation - Code P0171
I have 2007 explorer with the 4.6 V8....
Recently it started running horrible. Rough idle, drives badly, hesitation, etc. Check engine light is on, code P0171. I cannot find a vacuum leak, and i am pretty much at a loss. Before it started running poorly i replaced the thermostat, and flushed the coolant. I am assuming this is a coincidence.
Cherokee :: 1998 Jeep Started Shaking When Engine Started - Backfire
My '98 4.0 has 213k on it and the other day I started the engine and the jeep started shaking like crazy. Eventually the engine quit and refused to turn over so I looked under the hood and quickly discovered the problem, a deteriorated rubber elbow on the left manifold. The elbow connects to a threaded breather type valve in the manifold and has a thin piece of black plastic routing to the purge solenoid next to the left fender/air box.
When I removed the rubber elbow from the manifold the engine eventually turned over and idled fine, I then headed to autozone and found replacements of the same diameter, I cut them down a bit to match the length of the originals. Since its been a while I changed the plugs and wires, coil pack along with cap and rotor while I was at it. I replaced one plug and wire at a time to ensure I didn't mix things up, same goes for the cap. Now the jeep seems to take a few more seconds to get started but once it does it idles fine.
Now when I hit the gas hard the jeep will hesitate and then backfire. If I'm smooth on the gas the jeep drives good, whether city or highway. When coming to a stop the jeep will sometimes buck slightly like it wants to cut but doesn't. The backfire sounds like its coming from the air box and oddly enough, my aftermarket radio no longer plays in the accessory position, probably a separate issue. So far there's been no check engine light.
I really need to keep this jeep for a few more months and I would hate to put big money into at this stage.
Lumina :: 1993 - While Turning Makes Grinding Clattering Noise - Won't Move Forward But Will Move In Reverse
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
Chevrolet - Blazer :: Barely Move Forward And Will Not Move In Reverse
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesSanta FE SM (2001-06) :: Engine Will Keep Running And Car Won't Move
I have a 2002 Santa Fe V6. I'm getting the codes p1529, p0755, p0760, & p0765.
The car can start up & go, only for a short time. Engine will keep running, car won't move.
Kill the engine for 3 to 5 minutes, can start it up & go once again. Going 40mph increases the odds of the car not moving quicker.
Subaru - Outback :: Engine Rev When Pressed On Gas But Car Would Not Move
I have an 09 Subaru Outback. I filled up the tank at the gas station I usually goto. Drove about 30 miles on the tank to the airport where the car was parked for 5 days in an airport gated pay lot. Left the airport, I got about 10 miles and then the car would no longer accelerate. I pressed on the gas and could hear the engine rev, but the car would not move. I had to be towed to the Subaru dealer, where they said they could find nothing wrong with my car and they think I got some bad gasoline. They drained the tank and filled it up 1/2 way and the car runs fine. It still starts a little sluggish though. It sounds like it is laboring/revving when I first start the car after it has been sitting awhile, but once it is in gear it's fine. Is there anything I can do to fix the engine struggling when I first start the car?
View 13 RepliesPassat (B6) :: When Put In Any Gear Car Does Not Move At All And Engine Just Revs Up
So tonight my wife got off work at 7pm, she gives me a call and tells me she is on the side of the road. I was like wtf, what happened....anyways long story short I drive 30 miles out, by that time tow truck just arrived and flat beds the passat wagon to dealership.
So what my wife told me she got off work, drove about 2-3 miles down the road and then lost power and she pretty much came to a stop. Then she called me. Then tow truck came and towed it it dealer.
So issues I noticed, car starts fine, no engine lights on, but when you put in any gear, drive, reverse, sport mode etc. car does not move at all and engine just revs up. I'm think thing torque converter or something but really have no clue. Anyways tow truck tows car to dealer I start back up car and for f same car has power again can go forward, can go backwards! Yeah right, so I said let me see if I can drive around the block, so get in car start driving and then the power starts to fade and only drives about 100 feet before the lack of power happens and start to come to a stop. I did notice some slight grinding noise but by that time I wasn't moving anymore.
So we park in an open spot(had to push the beast) and then went home and here I sit and type my problem. What is going on and why all of a sudden without any notice this would happen. It has been a great car for us and we just had it in the dealer on Tuesday for oil change and they said everything looks good besides your rear pads are getting low... This just really sucks and couldn't of happened at a worse time. Just don't understand why the 2.0t transmission would do this all of a sudden. I pray that we don't need a new one replaced.
Camry :: 2004 Engine Never Starts And Tachometer Does Not Move
My 2004 Camry will not start; I have never had any starting issues before and the car was running perfectly hours before the problem started.
The battery is fully charged
The fuel pump is operating
The ignition and fuel pump fuses and relays are good
When I attempt to start the car everything sounds normal, but engine never starts and the tachometer does not move.
Additionally a soft buzzing noise starts coming from somewhere near the air filter box. The sound can be stopped by removing the "EFI" fuse. Disconnecting the injectors does not stop the sound.
Caravan/Voyager :: 1994 - Over Revving Engine To Get Van To Move
I have to over rev the engine to get the van to move. After that the tranny seems to work fine. Tranny fluid level is OK, and it does not smell burnt. After I over rev the engine to get moving, the engine revs seem to get back into sync for the speed I'm doing - usually just as the van starts moving, the over-revving is no longer there. Do I need to adjust the bands??
View 2 RepliesTouareg :: Engine Move When Accelerating After A Stop Or After Slowing?
Are the mounts on the engine not tight enough? It feels rather strange. My dad's Ford Explorer doesn't do that. I feel like I'm driving a car with a manual transmission that needs to have dogbone bushings and mounts upgraded. How do I bring this to dealership's attention without appear like a complete loony? They like to give the "Could not duplicate" response when there is an obvious symptom.
View 10 Replies