Prius (2004-09) :: 2006 - Got Codes P0301 And P0302 / Misfire At Low RPM?
This has been an ongoing issue with our 2006. We purchased the car about a year ago and have put on just over 8,000 miles. Rebuilt the battery pack and replaced the 12v battery. This is my wife's car and I have a 2005, so I have done some diagnostics, tuneup, and even swapped some parts between the two cars trying to narrow down the issues.
Only recently have codes been recorded. The car is has a noticeable misfire at low RPM. Here is what has happened up until now:
11/29/15 - replaced spark plugs - #1 was fouled so I swapped coils between cylinders 1 and 4
2/25/16 - replaced 12v battery with new battery
4/1/16 - P0300, P0301 codes were first recorded and reset to see if they came back
4/10/16 - swapped Integration Relay with my 2005 (part # 82641-47010). My 2005 ran poorly after the swap, so I put a used one in my 2005.
Prius (2010-12) :: Getting Error Codes P0302 And P3191
I leave my car for 2 weeks without driving, and when I start the power, I have check engine light on and I drive to the dealer right away. Mechanic performs diagnostic test for engine misfire no engine miss found. The error code is P0302/P3191. The mechanic told me that I always run the car in very low on fuel, and it causes the 2nd cylinder misfile or not running when the fuel is very low. They suggest me always pump the gas when the fuel indicator has 2 bars left.
My question is that: How come the car cannot run in low fuel, low fuel doesn't mean no fuel, and it can damage the engine/cylinder?
Ford Excursion :: 2000 - Misfire - Got Codes P0301 And P0302?
2000 Ford Ex 5.4 V8 175K miles
Top of radiator (plastic part) had a small crack and started leaking on drivers side. Fixed with JB Weld. Ran fine for a day. Now I have a bad misfire and codes P0301 and P0302 (Cyl 1 and 2). Cleaned MAF and checked Air Filter. All good. Plugs replaced at dealer less than 20K miles ago.
So I took off Cyl 5 (easiest) and found that the boot is fine but the collar on the boot is done for. Can this cause the issue?
Accent MC (2006-11) :: Misfire With Error Code P0302
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 RepliesPassat (B5) :: 2001 - Misfiring - Got Codes P0300 / P0301 / P0302 / P0303?
i have a 01 passat with a v6 in it on 4 motion and im having an issue with soem mis-firing
i pulled the codes. P0300 P0301 P0302 and P0303 which are all saying that there are missfires in cylander 1,2 and 3 and random miss fires.
im also getting a P0340 which is cam sensor A or the right hand bank. problem is i just replaced the cam sensor and when the motor got warm, the code came back. I was told by the previous owner that the car needed a Coolant Temp Sensor....can this be the cause of my mis-fire issue? hear me out.... it only happens when the car is warm so im thinking that the car is warm but the ecu thinks its cold cause its not getting a good signal from the CTS. thus its either advancing the timing as if the motor is cold and cuasing a miss fire or something along those lines. any thoughts?
Accent MC (2006-11) :: 2007 - Misfiring Codes P0300 And P0302
My girlfriends 2007 accent as thrown codes p0300 and p0302.
After reading everything I could find, I had coil pack on my list of possible problem items.
The car sat in the driveway yesterday and when she went to start it today, she couldn't get it to.
I got it to start when I got home by giving it some gas while turning the key, but I don't want to drive it anywhere.
The hard start is leading me to believe it's the coil pack.
I was going to start with changing the pcv, spark plugs, and run fuel injector cleaner through it because those are the cheap possibilities...but now may add in a new coil pack.
Accent MC (2006-11) :: 2010 GL - Misfire On Cylinder 2 / Code P0302
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
Accent MC (2006-11) :: Several Error Codes - Cylinder 3 Misfire
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 RepliesPassat (B5) :: P0340, P0300, P0301 And P0302 Scanned
I have a 2001 Passat 1.8 Turbo engine trim is AUG. My car is acting funny since yesterday. When i start my car it idles rough and CEL start flashing but as soon as i drive at like 10-15 MPH speed it becomes smooth and CEL stops blinking. I took my car to autozone and have it scanned got P0340 P0300 P0301 and P0302. It means random misfire and misfire in cylinder 1 and 2. I am not getting the misfire code for cylinder 3AND 4.
I swap coil boot 1,2 with 3 and 4. But misfire didn't move with cylinder. So i waited whole night reset CEL and swap coil 1 with 4 and 2 with 3. Have i scanned again not i am getting P0300 = random misfire and P0302 = misfire in cylinder 2. I didn't get P0301 this time.
Ford F-150 (2004-2008) :: 2006 V8 - OBD Error P0302 / Low RPM Torque Causes Major Shuddering
2006 F150, 4.6 V8 ... My truck was running fine until one morning I was sitting in the truck giving it my customary 30 second morning warm-up and it starting running very rough and quickly threw Check Engine LED.
I hooked up my laptop and got the following error codes: (To assist with future searches, the error codes are P0302, P0303, and P0353)
It seemed to drive fairly well, but low RPM torque causes major shuddering, so I try to keep the revs up to avoid damaging other components. The first step was to replace the spark plugs. They looked to be original and I'm at 140K on the truck, so it's probably time.
I went with Bosch Platinum as the factory plugs were platinum. When replacing the plugs, I moved the coil pack from cylinder 2 to cylinder 3 to determine if the problem would move. After the plug swap, the engine did run noticeably smoother (so the plugs worked overall), but still had the low rpm shudders and the same error codes (after clearing them).
Unfortunately, the error codes still indicate cylinder 2. I guess a misfire could be related to the fuel injector as well, not firing at the right time or not a complete spray, but what else could cause this?
Ford F-150 (2004-2008) :: 2006 V6 - Got Codes P0171 And P0302
I'm lost. Got P0171 and P0302 ... 2006 4.2 V6 5-speed 220K ... Got bad miss ...
Compression check was good.
Replaced plugs.
Replaced wires.
Replaced coil pack.
Cleaned MAF
Miss remains. What do I do next?
Kia - Rio :: 2006 - Check Engine Light Flashing / Codes P0302 And P0326
Kia rio 2006 130461 today I went and got gas right when I pulled out light began to flash and car shaking went to auto zone codes p0302 and p0326. I had knock senor changed 2 months ago . What could be the problem the guy said I just need a tune up . Is this true ? Is my car safe to drive car not shaking now and no changes in function of my car. There no way I can any one to look at it for couple begin tomorrow sunday.
View 19 RepliesFord - Explorer :: 1999 - Engine Rattling - Code P0301 / P0302 / P0303 / P0173 - Motor Shot?
My wife started our '99 Explorer last week and she said that the engine was rattling. I started it up when I got home and it sounded like something had let loose in the engine. We took it a local mechanic and he basically said that the motor was shot. I pulled the codes and it doesn't look good to me but I'm not a mechanic. Codes are:
P0301
P0302
P0303
P0173
Accent MC (2006-11) :: Shuddering When Vehicle Is Placed In Gear - Code P0301
When looking at the engine from the front of the vehicle. what numbers are the cylinders from left to right? To curtail off of that question where do I locate the corresponding ignition coils to these c I have been dealing with intermittent misfires on cylinders 1 and 3 codes P0300, P0301, P0303. I replaced the spark plugs to no avail. Whenever the vehicle shudders the headlights dim and the shuddering is worse when the vehicle is placed in gear, the A/C fan is on, or the vehicle is accelerating. Once I reach a certain speed, usually 35-40 mph, I don't notice until I again slow down. I replaced the spark plugs the day after I had the first issue appear which read code P0301. Prior to installing the spark plugs, I experienced a severe loss of acceleration power, but now only experience the shuddering.
2011 Hyundai Accent 63500 miles ....
Accent MC (2006-11) :: Engine Was Idling / Little Rough And P0302 Code Thrown
So I bought my accent used a couple months ago. It is a 2007 SE 3dr 5spd manual. It ran nice during my test drive and the price was right so I bought it.
Now I'm wondering if there is any way to find out the service history on the car...at least the major one's (30k, 60k)?
I ask because recently the engine was idling a little rough and it threw a P0302 code so I changed the spark plugs and holy-cruddy-deposits-batman those things were black. Gapped the new ones and popped them in and its a noticeable difference. My CEL keeps coming on and throwing a P0496 code as well, virtually once every tank of gas. Its not the gas cap so my next step there is to check the PCSV and hoses.
With these little problems, it makes me wonder about any larger issues. I know the timing belt on these things is supposed to be replaced at 60k. Additionally I would be willing to bet that my ECM software is out of date. Would Hyundai have records for any of the big maintenance milestones since they are required for warranty work?
How much does it cost to have a dealer check your ECM software and update it if needed?
Accent LC (2000-05) :: Sputtering Quite A Bit In All Gears / CEL With Error Codes
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
Prius (2004-09) :: Engine Light, Error Code P0301 Came On
So I changed my spark plugs, due to an error code saying p0301 which means cylinder one misfiring. I reset the engine light disconnecting the negative battery terminal. Once it reset it ran rough for a few miles. I put about 50 miles on it and it seems better.
View 2 RepliesPassat (B5) :: Misfire Detected - Error Code P0322 And P0302
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
Prius (2004-09) :: Number 1 Cylinder Misfire - Error Code P0301
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 Replies