Accent LC (2000-05) :: 2004 1.6L Rough Idle After Timing Belt Change But No Power Loss
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Slight Miss / Rough Idle / Loss Of Power
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Has A Rough Idle And Sounds Like There Is A Miss
I just installed glow plugs, ucvh, stage 2 rosewood injectors, t500, ipr and gear head tunes. I have out 97 miles on the truck since all this was installed and the truck seems to run okay but has a rough idle and sounds like there is a mis? What should I look into first?
View 12 RepliesAccent LC (2000-05) :: Odd Vibration And Belt Squeal Intermittently At Idle
I am posting about a cam sensor code and alternator belt squeal.
Yesterday after getting in from a 600 mile drive from salt lake to eastern Oregon i took a look at the car to put some fogs in and clean it up a bit. It had always had some odd vibration at idle and belt squeal intermittently at idle. I pressed down on the alternator at idle and the vibration noise went away. So bam. Found that.
The nut on the square head mounting bolt holding the alternator was missing. So it was kind of just flapping around. Replaced the bolt and put a lock nut on. Problem solved so I thought.
I'm still getting belt squeal. And i think that its out of alignment. It looks like the pulley side of the alternator is closer to the engine block than the other side. Is this adjustable? Is the bushing on the mounting side worn out to the point of movement? Is this fixable?
Santa FE SM (2001-06) :: Power Loss - Vibration / Missing When Idle
My father owns a 2003 Santa Fe GLS with the 2WD 2.7L V6 engine.
Recently it has been having lots of power loss issues. It vibrates/misses when idling, if you put your foot down on the gas pedal, whether under load or not, it sometimes stalls or just sits there. We took it to Hyundai, and they had no error codes. They charged us $150 to tell us nothing is wrong with it, when clearly something is. The car has become downright dangerous to drive because it cannot make it up hills without stalling/losing power.
The most recent thing we had done to it was the wires/spark plugs changed, which I think was at 65k on the odometer?
Accent LC (2000-05) :: Rough Idle While Drive Or Reverse
I have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
Ford 7.3L Power Stroke (1999-2003) :: 2001- Rough Idle - Power Loss?
Dad has a 01 one ton with the 7.3 and isn't real tech savvy so I'm posting for him. He is the original owner and has been complaining recently about the lack of power. Particularly the upper end. He is having to downshift way more often and where he used to not have to. And we've both noticed a very noticeable shake at idle. Not a vibration but a true shake. He changes the oil every 5000 on the dot and I've gone and changed the air and fuel filter and ran hose and see foam and royal purple injector cleaner through it with no results. Truck is all stock with 225000 on it.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - CEL - Rough Idle - Loss Of Power?
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
Ford 6.7L Power Stroke Diesel :: 2011 - Rough Idle - Surging And Loss Of Power?
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
Accent LC (2000-05) :: 2003 - Intermittent Rough Idle After Warm Up
This is what my car is doing after it warms up. It will do it then stop, then do it again and so on. I am pretty sure when the motor is under load it runs a little rough but is hard to tell. The car has 178,000 miles on it. timing belt was done at 113,000. I just replace the plugs and wires changed the oil and the air filter 1,000 miles ago. and it will still do it. I am at a loss as to why it keeps doing this. I have tried injector cleaner, sea foam and engine restore. What would cause this? The check engine light is not on. i replaced the crankshaft positioning sensor about 40,000 miles ago.
Its a 2003 hatch with the 1.6 5 speed .....
Accent LC (2000-05) :: Rough Idle And Bad Acceleration - Puffing / Rumbling
I'm an Accent 2000 gs owner and since a few days i had this problem. It has a bad idle and looks like it will stall... need to give some gas to stay alive.
Bad acceleration too, it misses some gas. (puffing, rumbling, shaking a bit). After accel, it's ok until the next red light.
Now I can't even drive cause it's worse. (too difficult to accelerate). Is it a sensor?
Accent LC (2000-05) :: Difficult Start / Rough Idle And Misfire
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
Accent LC (2000-05) :: Rough Idle For Few Seconds When Starting In Morning
I have a Hyundai-Accent 1.5 GL, Auto, year 2000 car. I bought this 4 months ago and ever since it has been giving the check engine signal. However, running conditions of the car has been normal and therefore, I didn't worry about the check engine signal. Now, the engine is rough idling for few seconds when I start the car in the morning, and then it comes back to normal.
View 12 RepliesSaab - 9-3 :: Rough Idle And Loss Of Power - Stalling On Start Up
SAAB 2007 9-3 - Recently my car has been having a rough idle and stalling on start up. It has been getting worse and I need it fixed ASAP for a long trip coming up. I cannot have this thing die on me while I'm 300 miles from home....
At stop lights the car will have a rough idle while in park and reverse. While in neutral, nothing. As soon as I accelerate, it goes away but does have a lack of power if I really push the pedal. Once I am in 3rd/4th gear, the car feels normal with no issues. If I am on the highway and slow down then need to accelerate, it goes back to losing power BUT if I change over to manual and downshift, car gains power and goes back to normal.
Here's what I have done so far:
1. Changed the spark plugs twice. Once with cheap ones, the second time with expensive ones. I also swapped out the boots.
2. Cleaned the MAP sensor
3. Cleaned intake sensor
4. Replaced air filter
5. Changed oil
6 New battery
The engines gives no codes whatsoever and I have taken it to a couple places and their readers don't see any codes. My SAAB has a built in fuel filter and this cannot be replaced unless you replaced the whole pump (to my understanding). I plan on buying some Seafoam today and see if that works. Also, I have been told to clean my air intake valve but I cannot get the damn tube off! I feel that if I yank and pull on it, it's going to damage the tube. I am not seeing any obvious leaks anywhere. One thing that is weird about my car, since I have bought it used a few years ago, my headlights/tail lights/blinkers go bad QUICKLY!
Accent LC (2000-05) :: Power Loss / CEL Blinking (Misfire)
So, I have a 2000 Hyundai Accent that has had the CEL light on ever since I have owned it (about 7 months). I was told it was the O2 sensor and did not have it scanned. Occasionally, it would lose power and the CEL would blink. After I would take my foot off of the pedal and baby it for a sec it would usually go solid again and drive okay. About 2 weeks ago it started blinking constantly and it sputters and drives like sh*t. Now, I know that I should take it to Autozone or someplace so that they can tell me which cylinder is misfiring and all, but it is really sketchy to drive. I put NGK spark plugs in it today with no change. I ordered plug wires and a coil pack to see if that straightens out the problem. If it doesn't then I am going to lean towards intake gasket or perhaps a missing or bad o-ring at an injector. So, does this sound like a reasonable plan of attack to get rid of the blinking CEL (misfire) and restore my Accent back to all of its craptastic glory?
View 2 RepliesAccent LC (2000-05) :: Cylinder Misfire / Rough Idle Then 2001 GS Dies
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 RepliesPassat (B5) :: 2001 VW - Rough Idle / Loss Of Power And Poor Gas Mileage
I have a 2001 VW Passat Wagon 1.8t AUG. A couple of months ago, I took it into my shop for a check engine light. The did the following work on the vehicle:
Replaced MAF sensor
Replaced broken oil level sensor
Replaced outer CV boots
Resealed my transmission pan (it was leaking)
Replaced bad vacuum hoses
When I got the car back, it was idling really rough, and one time it even stalled. Just after starting it, when I hit the gas it wouldn't respond immediately and sputtered for a little while. Once I got going it was usually OK, unless I was going uphill...where it wouldn't perform as well and the engine noise kinda wavered. I also noticed that my gas mileage wasn't nearly as good as it used to be. (I never experienced any problems like this before they did this work) So I took it back to the shop and they replaced both the front and rear 02 sensors. I still had the same problem, so I took it back, and they replaced the fuel filter. Still has the same problem.
The light came on after a month, so I took it back and it was the random cylinder misfire code...and they said that didn't really know what to do about it. So I decided to take matters into my own hands. I cleaned the MAF sensor they installed (took it out and sprayed it with cleaner) nothing. I replaced the spark plugs and while doing so found that one of my ignition coils was bad, and I replaced that as well. Turns out the AutoLite plugs that a local parts store sold me are crap for this engine (actually caused misfires) so I went and got Denso double platinum plugs the next day and put those in. And finally I changed my air filter. Still having problems.
Ford F-150 (2004-2008) :: 2005 - Rough Idle - Power Loss?
my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.
It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:
Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket
Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.
Ford - Explorer :: 2007 - Rough Idle / Power Loss Sometimes While Driving
Explorer with 4.0 has a rough idle, just put new plugs & wires, air filter looks good. i did get a new fuel filter as well but haven't gotten to that yet. It has 102k. I have read some info about motor mounts could come lose casing the motor move a little more, not sure about that one. its the wife's haven't driven or looked into it yet, its on the to do list weekend. She also informed that it seems to lose power a little while driving sometimes, thinking possible fuel pump now?
View 4 Replies